what happen when you doing calllibration, but it stuck at run 2 for long time.

Highly appreciate your kind & detailed stepby step video. May god Bless You. Keep making this types of videos regularly.

Excellent job! But what about the mechanical yellow rotatory selector at the left and the other one...the internal down/up mechanical switch at the center, please?

Is it available to change Totalizer reading for certain reading?

the instrument remains in power on... the possible cause???

Thanks

Vagas?

Very good explained, very well organized video. Have on question: What’s the difference between this ps2 and Bray 6a positioner? Their design and operation is almost the same, why?

Thanks for sharing video

Want to open 100% in 19ma current what do????

Since it read auto 20 when valve is fully shut so how to bring to auto 0 when valve is fully shut?

How to reset ps2 sir?

Chow to reset hardware failure alarm

I have been facing an error during Run 1 stage seimen sp2 positisoner, could u please share your comments on this issue.

Valve jammed alarm alawys coming without mechanical problems. Why?

Hello

মো: শাহীন সরকা আমি এটা ব্যাবহার করছি পজিশনার ভাল্ব খুব ভালো কাজ করে। সোনালী পেপার মিল 🇧🇩

Thanks for posting this 🙏🏻

What us identical limit fault?

Valuable content. Thank you. Bad audio quality. If you redo this mic the technician with a lapel mic, drop the music, and try to plug the air hiss (this may be part of normal operation).

If it’s 24vdc is required?

"PromoSM"

so whats the purpose of adjusting??

What would cause the actuator to travel open slowly to the point that it times out in auto remote on DCs and fails close? Locally, the valve opens and closes in 2pct increments. Thank you.

I have a question after the limit stops have been set, I noticed I had trouble with a timeout torque alarm. The valve opens very slowly 2pct at a time when it should normally respond at a 10 to 12 pct . How do I resolve this issue? Thanks.

I'm still learning on your channel

Great vid bud

Sdh 27 th bergelut dgn positioner seperti ini

How tu resetting

☝️ P R O M O S M.

Hiii, i am getting problem in MX 05 series MOV. in the display showing Tourqe percentage and the position either open or close in the scada DCS its showing anything. please advice me regarding this issue. and the termination details of open command, close command, stop command. and open position, close position, remote / Local position.

What happens if the firmware doesn't reload the settings when flicking to local and stays at set close position.

ตั้งเวลาและเพิ่มแรงดันยังไงครับ

How to found the error in the siparta PS2 possotioner

Sir What about overtourque settings? My acuqater when close it got overtourque and i have to put it to local then open then returned it back to remote to get ok and cleat the overtourque?

derivative of square root of x-6

Hello , I have a question ; Even though there is 4mA in operation card, in the screen of valve appears AUTO 100 . Is there a problem with the settings of the valve? So valve is bot taking action accreding to plc command.

Can I remove the current settings and reset them to the default settings?

Thank you very much but could I have the video in French please thank you in advance

i think 15 psi (open position ) should be green (C C W)

Can anyone tell me why there is a hand lever on it? Is it for locking?

Can we get Valve position feedback from any terminal to an analogy input card to plc.

How to set valve close on to torque not limit

Sir bladpoch actuator comissning

Ok Very good

supply for Banglades

I am inspired... Mankind, that word should have new meaning for all of us today. We can’t be consumed by our petty differences anymore. We will be united in our common interests. Perhaps it’s fate that today is the 4th of July and you will once again be fighting for our freedom not from tyranny, oppression, or persecution but from annihilation. We’re fighting for our right to live, to exist, and should we win today the 4th of July will no longer be known as an American holiday but as the day when the world declared in one voice We will not go quietly into the night. We will not vanish without a fight. We’re going to live on. We’re going to survive. Today we celebrate our Independence Day!

good design

Akhirnya menemukan Chanel instrukent yg Indonesia 😁. Thanks gan ilmunya semoga banyak rejeki 🤲

How much it cost? Where to order them?