Thank you

Thank you 🙏

Here are most common problems and solutions from easy to hard 1- bad spark plug, clean or replace 2- spark plug cable bad or has shortage, replace 3- Ignition coil, burned or bad , replace. Thank you and all the best 🙏

You're welcome,, thank you and all the best 🙏

My pleasure 😊, thank you so much and all the best 🙏

Yes that's what I thought too, but it was the magnetron burned, thank you

On my unit it was the diode after all, all other components were working perfectly, and I was scratching my head lol...until I saw your video...crazy a cheap component like that can make or brake the whole system....

@leemathoo6583 , I was also confused about hight voltage diode, so after you replaced the diode it works fine? And Does the burned diode made the microwave not heating ? , it's interesting to know , thank you and all the best 🙏

My pleasure 😊, I am glad you found my video was helpful, thank you so much and all the best 🙏

Unfortunately this I got it's upsidefown, but will upload new video probably it fixable, thank you and all the best 🙏

Hello My Friend, i received many messages and comments people have difficulties or defects with this type of camera, I wonder if your camera is working fine? Thank you so Much and all the best 🙏💕🙏💕

Yes it works everytime but sometimes it takes little longer it depends on the tire edges must contact with rim all at once, thank you so much and all the best 🙏🙏🙏

Power button if it's touch or soft touch press It's either the base of the black graphite dirty or corrosioned or the button bottom Both need cleaned with medical alcohol, if the power button old style mechanical press it could be the legs are loosed or not connected to electronic board, or power button switch is bad, check the electronic board if any cracks or cut connections, thank you and all the best 🙏

Yes unfortunately I did 4 and 5 times and both didn't work , but 5 times it was unfortunately off camera, thank you and all the best 🙏

Hello my friend, to clean the tensioner if you think it has threads stuck you need to remove the covers completely to access to tensioner 2- to adjust the threads tensioner watch this video Link here thank you and all the best 🙏 kzbin.info/www/bejne/qH6qfKCIja-IepYsi=A833MIW9W8SBg5HK

Thank you so much 😊🙏😊🙏

Thank you so much 👍😊

Use protection gloves.... and eye protection

@leemathoo6583 , yes it's very important for safety, i don't because this particular Microwave never store any high voltage as soon as unplugged from power , but maybe some other microwaves store hight voltages so it's very recommended to wear gloves and safety Glasses, thank you so much and all the best 🙏

My pleasure 😊, thank you so much and all the best 🙏

Sure 😊, it's not easy to find parta and if found will be so expensive, thank you so much and all the best 🙏💗

Right 👍, thank you and all the best 🙏

My pleasure 😊, I am glad to read your wonderful comment 💗😊, thank you so much and all the best 🙏

Hello my friend, on other websites instructions says 4 time but anytime I did 4 and 5 times nothing worked, unfortunately 5 times done off camera, thank you and all the best 🙏

You can buy them from AliExpress or eBay or Amazon, there are many different designs and sizes too, thank you and all the best 🙏🙏🙏

hallo mein Freund, das ist schön, dass wir dieselbe Nähmaschine haben, es ist gut zu wissen, ich liebe Nähmaschinen. Meine beiden Brüder und meine Schwester hatten früher ihr eigenes Nähgeschäft, aber ich habe keine Zeit zum Nähen, ich mache lieber Wartungsarbeiten und repariere sie. Übrigens, dein Kanal ist großartig, vielen Dank und alles Gute 🙏💓🙏. hello my friend, that's nice we have same sewing machine, it's good know, I love sewing machines my 2 brothers and my sister they used to have thier own sewing shop, but I don't have time to sew, I like to do maintenance and fix them، by the way your channel is awesome thank you so much and all the best 🙏💓🙏💓

Excellent point, yes it's a good idea to to make it little higher for safe stop ,thank you so much and all the best 🙏❤️

I am so glad to hear that, my next video I will use this refrigerator compressor to make soundless home compressor, thank you so much and all the best 🙏❤️🙏❤️

Hello my friend, there are several issues can cause that, you can try the following steps or visit those 2 links for more details, Please try that:Turn the power of the instrument off. Then, while holding down the lowest key, press the [ ] (Standby/On) switch to turn on the power again so that the [REC] indicator flashes three times.Once you do that try to turn on the piano the regular way.I hope that helps, you try unplug it from the power outlet > leave it like that for at least 1 minute > press the power button for at least 15 seconds > plug the power cord to the outlet and try to turn it on again. gzhls.at/blob/ldb/e/b/8/e/2140f7dccbc09461a29e13e4733e2eaf4cbf.pdf pianotechniciantuner.com/blog/Blinking-Flashing-Lights-Guide-Yamaha-Enspire-Disklavier Good luck and all the best 🙏 Let me know if the problem is solved Thank you 😊

@@WorldRandomVideos that's so kind of you. I really appreciate it thank you, I'll give it a try. .

Thank you so much I will do that with a video soon, all the best 🙏

Hello my friend, yes after the problem fixed the battery power works too, the main power is connected to battery power as well, thank you so much 🙏 and All the best ❣️

That’s very helpful. Thank you. I’m trying to figure out the issue with mine

@mendozawav8202 my pleasure 😊

Most likely is the wire has cut or shortage, or maybe the speaker is bad or damaged, the only way you can tell by testing, deassemble the the headphones to access the speaker connection wires and use Multimeter on Ohm if there's no reading at all means the speaker is burned, must be replaced, you can also test the speaker simply use 1.5 v battery connect the + to + and - to - if you hear a noise the speaker is good if you don't hear nothing the speaker is burned, to test the wires put multimeter to continuy position connect 2 probes on male jack to speakers try all jack rings if one of the 2 wires has cut multimeter doesn't make sound or continuity, then you need to trace the cut where is located, I hope that will help you to figure out thank you and all the best 🙏😊

@@WorldRandomVideos thank you, i will get it to a technician

@Shashamura10 my pleasure 😊

It's factory defect , I think nothing you can fix this issue, some models don't even have WiFi, thank you and all the best 🙏

Factory Defect

I had 3 of them I left them for about 4 weeks I didn't use them after I checked the battery power all were okay, no Power drain, but all had about 90% left , which is reasonable, I think yours probably had a problem with battery power leakage, did you fully charge the battery before you use for first time? Did you know that most batteries most types and made if they don't use for few weeks or so they all get power drain or leakage , Thank you all the best 🙏

Thank you so much for your wonderful comment and useful information, I didn't like it because it's little thick and yes it's leaning down little bit I guess it's ment to be ladt Long time

I am sorry, the video is speed 3× because it was too long, thank you and all the best 🙏

Hello my friend, Try the following steps: 1- check or test the power supply or adapter with power Cord use multimeter test the voltage it should be same what label manufacturer sticker on power supply, if it's less that means power supply is not good or if there's no voltage means it's burned, and either way it must be replaced, 2- check the power cable jack male and female if the piano power Jack is loosed or moves then it has damaged from inside with motherboard connection, Sometimes the power cable jack has shortage or cut, test voltage while move it left and right to make sure it's not shortage 3- if all ok then the problem it could be inside electronic boards check if there's a crack broken connections or wires shortages etc, I hope that will be helpful, best regards 😊

Awesome 👍, Are they made of wood also ? Thank you so Much and all the best 🙏

Hello my friend, I am sorry I had to seed up my video because it was too long, thank you so much 🙏😔 and all the best ❣️

Hello my friend, I don't think this camera has battery so if the main power cable is disconnected when the car is off the camera will turn off as soon as you turn key on on position and the cigarette lighter 12v outlet is on the camera will turn on, Some good dash cameras have back up battery, this on doesn't, I will also double check to make sure and I will upload a video soon for more details Thank you and all the best 🙏🙏

Hello my friend, it's available from aliexpress, here's the link Just found this amazing item on AliExpress. Check it out! C$43.38 | Adjustable Digital Hot Air Gun Heat gun Soldering Desoldering solder Station SMD BGA 8018LCD+heating element 220V LCD a.aliexpress.com/_mKpaYmI

Thank you so much 😊🙏😊 and all the best ❤️🙏

Hello my friend, awesome 👍, I will try that, and upload new video thank you so much and all the best 🙏❤️

Hello my friend, I will look for that link and send it to you, thank you so much and all the best 🙏

Hello my friend, press and hold the button on the center of the speed Dial to reverse, thank you and all the best 🙏❤️

My pleasure 😊, thank you so much and all the best 🙏🙏💓

Awesome 👍, yes I did , I had to go through that for best results possible as test, thank you and all the best 🙏

I am happy to help 🙏, thank you so much and all the best 🙏😊

Yes still runs strong too, thank you and all the best 🙏💗

Thank you so much 🙏, I changed multimeter doide mode but unfortunately it was off the camera and still didn't read nothing, thank you again and all the best

No, they shouldn't, if the bolts are tight enough equally and all the locker washers so the bolt never loosen, thank you and all the best 🙏😊

Awesome 👍, good to know that that's what I was been told too, do you know if there's a way to test high voltage diode? Thank you and all the best 🙏😊

Yes google "how to test a HV diode with 9 volt multi tester battery .