simple

Пікірлер

@peterbest3769 6 күн бұрын

I have ae91 toyota 1 gear shift at about 25 , how do i ajust it to change blow 20 . What the setting for the cables

@simple8818 5 күн бұрын

There is no way to adjust the cable to shift at ceratin speed. Check the cable for looseness. If not loose there could be a transmission issue. Thanks.

@AbidZehra2024 2 ай бұрын

Problem Jatco bmw e39 1999 delay :/

@desr924 3 ай бұрын

Does this work with Nissan Rogue?

@simple8818 3 ай бұрын

I'm not certain what method the Rogure uses.

@paulsullivan8368 3 ай бұрын

Is it just me or is the audio very poor on this?

@jiggamanog 4 ай бұрын

Good job nunb nuts is the bolt reverse thread or what? Terrible video

@simple8818 4 ай бұрын

Haha. I’m not in it for the money. you get what you pay for 😂

@RobertSmith-js2kz 6 ай бұрын

Should have changed those bearings while you were in there. They should make no sound whatsoever

@simple8818 6 ай бұрын

Lexus no longer sells the valve or bearing. Aftermarket is a no go unless absoilutely necessary. Thanks.

@RobertSmith-js2kz 6 ай бұрын

@@simple8818 There are TWO bearings in there and you can buy them anywhere. I just did mine a few days ago. You didn't even do half the job son.

@simple8818 6 ай бұрын

@@RobertSmith-js2kz Can you provide the link to the bearings? I didn't see them on Lexus site!

@ginaforfsu 7 ай бұрын

The green grommet cracked apart and left the brake lights on in my brother’s car too. We just cut a magnet in the same shape and taped it in place. Fixed it.

@Matt-c5f9o Жыл бұрын

THANKS! Helped me a lot. My brake lights were staying on even when car was off...had to pull the fuse to shut them off. I found that my switch was actually good...the green plastic spacer was cracked and fell apart. So I made one out of a plastic bottle cap by cutting it down and then heated it up with a lighter to mold a nipple in center so it would seat into hole on brake pedal arm, and filled in the recessed other side with melted plastic...and put some super glue on it, and on the retaining nut as well since It would have been very difficult to get a wrench in there. Works great now.

@Matt-c5f9o Жыл бұрын

...alsoI didn't have to remove any panel...just pulled the connector off and then was able to unscrew the switch. Hope this helps someone.

@simple8818 Жыл бұрын

Glad you found the workaround.

@zemwazhere1489 Жыл бұрын

Hoping this fixes my stalling issue on my 95 LS400 gonna order a new gasket for it then clean it good

@zemwazhere1489 Жыл бұрын

Drove it around town after cleaning it no stalling💪

@ronniem3592 Жыл бұрын

That inner tie-rod needs to be changed!🤔

@johnk3606 Жыл бұрын

If you use atf you will eventually get pump whine. Once you do get pump whine, because you will ignore or refute this comment, flush the system with power steering fluid and the whine may go away if you’re lucky. I know you used atf in your last car but this pump will whine if you use it.

@simple8818 Жыл бұрын

I use the oil lexus recommends and never had whining issue although you are free to use whatever you think it’s best for you. Thanks for the comment.

@TooFlyNico Жыл бұрын

Do you own an ls400? Cause it sounds like you don’t know what you’re talking about lol. If you used regular PS fluid the PS pump well grenade itself. These cars take ATF. Can read it in the owners manual

@donderfoil 7 ай бұрын

power steering fluid tf?

@RobertSmith-js2kz Ай бұрын

It's what the manual calls for. Old school Dex/Merc to be exact.

@dangalanga6941 Жыл бұрын

I had this issue start with my ford AU2 Ute and I’m so glad I saw your vid 🤙 I fully thought something was wrong with the gearbox itself

@hellnowhere Жыл бұрын

Looks a little lose

@jamesimmeker4045 Жыл бұрын

really did not show how to remove it or reinstall, not much worth seeing!!

@simple8818 Жыл бұрын

I did not want to repeat other videos which cover the removal process. Brake light switch removal is very similar to other cars. Thanks.

@victorrobles7499 Жыл бұрын

would a 1997 ls400 pump fit a 1997 celsior? i know its the same but i want to know

@simple8818 Жыл бұрын

As far as I know Celsior was the name of LS sold domestically in Japan. Your Lexus or Celsior dealer can verify; and buy OE parts not aftermarket. Thanks

@davidgarnier6972 Жыл бұрын

What is that button above the parking 🅿 button for my rx300 awd is missing that button so I'm trying to find out what it does thank you

@simple8818 Жыл бұрын

This botton which should have a black cover, is for emergency shifting the gear to Neutral without the key in the ignition like when towing. There should be videos explaing this action. Not sure why your model doesn't have this or all you see is the black cover. Thanks.

@azdronedude Жыл бұрын

Nice job Master Mechanic

@jacentalynott931 Жыл бұрын

'promosm' 😈

@DPoner Жыл бұрын

I wonder if this will work on my ranger. It’s doing the exact same thing.

@simple8818 Жыл бұрын

You would need to find out if your truck uses Throttle Cable. Newer model automobiles use Throttle by Wire instead.

@DPoner Жыл бұрын

@@simple8818 yes has cable. Thank you. I’ll try it out.

@ooteshdoolub8763 Жыл бұрын

Thank man 🙏 you are boss you save my time and money tho one more to time

@bilygates2509 Жыл бұрын

Outstanding 😮.. thank you for saving the day my car improved instantly 👌🙏

@kiwanmansoor2863 Жыл бұрын

Sir corlla 92 1st generation 5A with auto cable gear . car shift 1st gear to 2nd gear on 2200 rpm . Is it normal or high. Due to high rpm shifting car consuming high gas . I check and very lose kick down cable but problem same. Any suggestions pl

@simple8818 Жыл бұрын

Hi Kiwan, please check the ATF level and color of the fluid. If it is very dark (brown/black), it might need a flush; but ATF flush can cause transmission issue if it's never been done. It all depends on how regularly the transmission fluid was maintained in the past.

@kiwanmansoor2863 Жыл бұрын

@@simple8818 thanks for ur kind reply. Do u think is there is solenoid issue? Transmissionoil color is red . Whixh is pretty new with thickness when u check it with ur fingers. Whats elea i can check or do? What is normal Rpm for shifting from 1sr gear to 2nd gear.

@simple8818 Жыл бұрын

@@kiwanmansoor2863 I could't tell you much about your transmission and what the RPM should be. Have you looked up videos? You can search the web for your car's transmission documentation or purchase a used Toyota shop manual. Good luck.

@omeedkhatami4649 Жыл бұрын

Excellent breakdown of steps, that new pump looks very nice!!!

@omeedkhatami4649 Жыл бұрын

Who knew a thorough clean would make sure a big difference!?!? You made the difficult method look easy!

@danielsexton1608 Жыл бұрын

Hi, could you tell me the location and how to remove the SRS control unit on My 2001 Lexus RX300. I have to send out to get reset. Thanks Daniel

@chriswestbrook2645 Жыл бұрын

Use FULLY SYNTHETIC oil. Mobil. Then come back here and tell if that helped.

@omeedkhatami4649 Жыл бұрын

Excellent tutorial, couldn’t find a clear instruction video!

@omeedkhatami4649 Жыл бұрын

Great demonstration! Makes a seemingly challenging task seem easy👏

@karimbakri8006 Жыл бұрын

My cable will not tighten anymore I turned the nut all the way but stopper will not go any closer to the end do I need a new cable?

@simple8818 Жыл бұрын

Hi Karin, if the car is still shifting abnormally then the issue may be somewhere else.

@siah_6008 2 жыл бұрын

I have an issue on my 94 sc 400 when I step in the throttle all the way when I’m going 50mph it used to downshift to 2nd for faster acceleration but now it only downshifts one gear could it be from the throttle cable?

@simple8818 Жыл бұрын

I’ll try the same procedure and let you know how my LS behaves. I recently did Valve clearance adjustment and car downshifts better when stepped on. Cleaned the TB front and back.

@simple8818 Жыл бұрын

My car(LS400) does the same as yours when stepping on accelerator.

@oceanpacific3841 2 жыл бұрын

I have a question ,my car has two cables just like yours ,it looks like one is to adjust the throttle cable but what's the other cable for ? When I loosen my throttle cable does it create slack for the other cable ?

@simple8818 2 жыл бұрын

My other cable is for Cruise Control. It wouldn't cause a slack.

@oceanpacific3841 2 жыл бұрын

@@simple8818 I posted my comment before watching the whole video. When I loosen the throttle cable does it leave slack for the accelerator cable ?

@simple8818 2 жыл бұрын

@@oceanpacific3841 My reply was it shouldn't. Additionaly, what needs to be tested also is the cruise control operation after your work is completed. IF cruise never worked before that is a different issue. Good luck.

@simple8818 2 жыл бұрын

Lookin more closely at your question those two cables are the same. Throttle cable is the accelarator cable! If you need more help post your question at mechanic forums. Thanks.

@oceanpacific3841 2 жыл бұрын

@@simple8818 thank you for your help Sir :)

@nshasnu3209 2 жыл бұрын

❤️(Hi sir pls help me to know the solution) i have nissan tiida 2006 & once my car engine gets cool like every after 4 or 5hrs later if i start my car then i shift the gear into D it takes 10 to 20 seconds to run the vehicle please let me know solution thanks lot

@precisiont5188 2 жыл бұрын

Do new cars also have throttle cables?

@simple8818 2 жыл бұрын

No most are using throttle by wire sending electronic signals instead of using cable.

@vplacio 2 жыл бұрын

can you show how to really replace the switch? specially to remove the panel

@simple8818 2 жыл бұрын

There are other videos that go thru step by step since the process of removing the switch is similar with other cars. As far as the kick panel goes the removal is easy but it gets harder from there when it comes time to replace the switch. Since we are dealing with brakes I recommend asking an expert mechanic.

@lisagallups9792 2 жыл бұрын

I'm having the same issues on a kia sportage I sure hope this solves my problem as well ...thank you for sharing I would not have thought that ..thanks bunches god bless

@simple8818 2 жыл бұрын

Depends on wether the Sportage uses cable or not. Newer cars use electrical wire rather than cable.

@Apexlive-EMD 2 жыл бұрын

Thanks alot man this video helped alot

@binarylife 2 жыл бұрын

Really appreciated.

@markloveable1 2 жыл бұрын

Thank you for that information

@omeedkhatami4649 2 жыл бұрын

Nice replacement!

@omeedkhatami4649 2 жыл бұрын

Insightful elimination step to this problem!

@Lucentlens 2 жыл бұрын

[From the UK, 2022] Excellent video sir - many thanks.

@ivanchostefanovski2351 2 жыл бұрын

On previous post j forgot to mention j change the fluid and filter twice and the 3 magnet was absolutely clean (0) both times .If some part of gearbox is broken there will be something on the magnet?

@simple8818 2 жыл бұрын

Not necessarily. There are times when small pirces of metal are found on the magnet due to wear and tear. Some cars are just notirious for transmission issues. Search for your car model to see if others are complaining about the transmission. Also mileage of the car plays a factor. Hope this helps.

@ivanchostefanovski2351 2 жыл бұрын

J have toyota camry1992 2.2 automatic transmitions . 3 position of 6 are ok. Gearbox Work only in P --parking R ---reverse and N ---neutral .Don't work at all D---drive 2-- and L --- limp mode.On the dashboard display all lights work only the D drive Don't work. Also the back up lights and reverse light don't work. What is the problem neutral safety switch? Shifter or something else.Is it possible to put the transmition in D drive mehanical by hand ? J AM asking this because the mehanic says the gearbox is broken and j should buy a new.In reverse the car ride great .What is the problem

@simple8818 2 жыл бұрын

It's not possible to provide mechanical solution. Take a look at this video: kzbin.info/www/bejne/qYLIiWWGodqeg6s

@corneliustriplett4796 2 жыл бұрын

So how did u fix it

@omeedkhatami4649 2 жыл бұрын

Best video yet!!

@kevinliu3230 2 жыл бұрын

Excellent instruction.

@simple8818 2 жыл бұрын

Glad it was helpful!

@leiladaquil6587 2 жыл бұрын

Now I understand automatic tranny comes in kick down cable control and electronic Trans control module.Good to start diagnosing all controls located outside first rather than jump to solenoid,gear set,oil level,etc.thank you for the good video.

@guyfawkesuThe1 2 жыл бұрын

Get a low-cost cordless ratchet off of Amazon for about $40 bucks! kzbin.info/www/bejne/pWnVh2SCaa-Zas0

@Vishal-gk4qg 2 жыл бұрын

Good

@RockwearbyEddie 2 жыл бұрын

So after adjusting the first nut counter-clockwise to adjust the cable and it's where you need it to be, you don't tighten the nut up that's closest to the black plastic cover to tighten it up?

@simple8818 2 жыл бұрын

Tighten both nuts. I believe there is a comment towards the end of the video. Thanks.

@dwarkapersaud8434 2 жыл бұрын

i was getting this problem for years since i bought my car and i finally got it fix and decide to check if anyone make a video

Ең жақсы KZbin

Пікірлер