Great video, can you show more about when butting in diffrent templates on untility run? I have one with 3 diffrent template on one utility run and I started at a wrong chainage and cant find out to fix it.
@mappuhhstudioofficial Жыл бұрын
I have used Trimble products throughout my military career, and you mentioned setting the Elevation mask for satellites at 10 degrees. We normally set the elevation mask to 15 degrees; however, we would lower the elevation mask to 10 or sometimes 5 degrees, especially in areas that enabled us to grab or use more data from more satellites if we were experiencing a lot of cycle slips or other interferences from some satellites that were skewing our data. Then I would disable those bad satellites from being used for processing, and use the available satellites that were in the range of 5 or 10 degrees above the horizon to potentially give us a stronger data network tie. If not we would run another session or two as necessary.
@JacquesTreehorn Жыл бұрын
I thought Trimble DL stood for down load. Data Logging makes more sense. Been thinking that for 4 years. Been telling people to look for the app as Trimble DL and saying down load. I like it. It is faster than the wired data transfer app. You don't need the special Windows 10 usb to serial. Use Android with Trimble in general. iPhones wont take a beam from the TCS3s
@danielcastillomeneses3248 Жыл бұрын
Cuento con la versión 5.9 de trimble bussiness center y no puedo dar con la colectora DAP194600070 V3.0 pueden subir alguna ayuda para actualizar las controladoras.
@nadernader6420 Жыл бұрын
dear sir, why when making IFC file and opening it by tekla again the bolts have disappeared. I asked some friends and they told me that tekla does not convert the bolts in the IFC file. is that correct?
@MrWebon2 жыл бұрын
Thanks!. Is it possible to break down the utility takeoff report by Areas Of Interest?
@shabeaf052 жыл бұрын
with the TSC7 can Trimble field link be used?
@bongicannabinola30542 жыл бұрын
Hahahahhaha
@dwightwomack67462 жыл бұрын
Well done! learned a lot
@SpectrumDrone2 жыл бұрын
Nicely presented , easy to get an understanding of the entire platform and individual apps that make up the platform.
@redhead1002ify2 жыл бұрын
How do you get raw data from the measured control points?
@dicky1612933 жыл бұрын
Mary and Mvil is the control point right? at the first base line process, why you set all of point as control? and after the process you decide the control point (mary and mvil). shouldn't it determined at the beginning before the process?
@dicky1612933 жыл бұрын
i have some question, why you dont process at same time all of sesion on that project?
@fihdsertomayochuquicondo7483 жыл бұрын
podría por favor explicar en español
@craftey08carper3 жыл бұрын
Do you have a link to run this software on Mac OS?
@SitechCS3 жыл бұрын
Hi Martin, I don't believe any of our Trimble emulators will run on Mac. You will need to run an android or Windows cloning. Feel free to contact us on 1800 748 324 if you need to speak with somebody about this.
@craftey08carper3 жыл бұрын
@@SitechCS thanks for the confirmation, sent a request for training and information via the Uk website, no response yet though.
@roderiquevictor98013 жыл бұрын
Evening, my name is Roderique Victor from Namibia. I am a Survey Technician. I would like to know to what format should I convert my Leica GPS 1200 raw data to enable it to be compatible for import into Trimble Business Centre. I have the 2013 version
@rossmcatamney59213 жыл бұрын
Hi Roderique, Couple of things here, are you looking at using Raw or Static data? If you are using Static data then you will get the RINEX file out of the controller and use that to then download the ephemeris data in TBC. Alternatively if you are using RAW data I would recommend updating to the current version of TBC which will support the HeXML format. In the version you are using there isn't an easy process without taking the data out through another package to get a file format that is support in TBC.
@rodnose93504 жыл бұрын
really bad trimble don't have a proper user guide for control box using a dozer,been looking for a while few things I need and can't find anything ,totally useless Trimble website like this video
@aureliotrevisiol7564 жыл бұрын
Great stuff....i really enjoyed the details that were presented. This is better than Revit.
@commanderjarak4 жыл бұрын
Is it similar to delete design files from a D6 running CAT Grade?
@군산김도현4 жыл бұрын
새로운시대를 늦게 맞이하는거죠.
@Trimble_Korea4 жыл бұрын
무플방지위원회에서 왔다가요.
@julianmartinez85494 жыл бұрын
Where Can I find that ADAC template .fxl you imported at the very beginning?
@lesleybrigden90774 жыл бұрын
Hi Julian, please contact [email protected] or phone 07 3851 8322. Ramin will be able to help you.
@patrickcavanaugh44554 жыл бұрын
Pretty sure Microstation was like built for doing this
@luismadris50975 жыл бұрын
Need some help in how to get a file into roads, please help.
@nembhardandre5 жыл бұрын
How do I delete a work order and Design?..plz
@shaungray16145 жыл бұрын
You cannot delete a work order or design through the SCS900 software. You can however delete a design or work order through the file explorer software on your particular device. On a Windows Mobile device you will find the designs in \\Trimble SCS900 Data\'YOUR SITE NAME'\Designs\'YOUR DESIGN NAME' and you work orders in \\Trimble SCS900 Data\'YOUR SITE NAME'\Work Orders\'YOUR WORK ORDER NAME'. If you delete the folder with your work order or design name, it wont be available the next time you open the SCS900 software. On a Windows Vista/7/8/10 device you will find those folders in C:\Trimble Synchronizer Data\PC\Trimble SCS900 Data\'YOUR SITE NAME'\Designs\'YOUR DESIGN NAME' and C:\Trimble Synchronizer Data\PC\Trimble SCS900 Data\'YOUR SITE NAME'\Work Orders\'YOUR WORK ORDER NAME' respectively. The reason you cannot delete the Designs or Work Orders through the SCS900 software is to prevent the designs and work orders created in the office from being accidentally deleted or modified in the field to protect the original data and associated field recorded data.
@nembhardandre5 жыл бұрын
@@shaungray1614 ...thanks
@MikeHF5 жыл бұрын
@@shaungray1614 Can I plug my TSC3 data collector into my home PC and delete jobs like you mentioned above through the USB port?
@frodozrychnova6 жыл бұрын
Hello, I am working with this machine control lately. If I could ask one question, what for is the .SVL file. If i open it in HCE BC it is just a flat line version of my surface in fix height. If I am choosing the working design in excavator's computer I can only pick the .SVD. So do I actually need it for something or .SVD and .CFG together could be enough? Also if I am doing the file in HCE BC from surface in format .LandXML the outcome is .CFG and .SVD only. If I am doing it from surface in fromat .dxf the outcome is all thre .CFG and .SVD and also .SVL. Thank you Josef
@4815162342SW7 жыл бұрын
Thanks for the Video, How can I export .RXL files with a road corridor? I really hope the answer isn't use TBC because creating a job site and assigning controllers is a long winded and unnecessary process. Can it be done from a USB stick?
@MikeHF5 жыл бұрын
There is no shortage of unnecessary processes with these things. Sometimes I wonder if the unnecessary complexity is done so for a certain purpose not related to getting more work done in the field.
@mitchell6177 жыл бұрын
Awesome
@robertocolella96527 жыл бұрын
istruzioni in francese
@fengwan60628 жыл бұрын
214
@mihainita66568 жыл бұрын
Hi there. I have a genio file from the designer which I want to import into TBC. When I import the file I get 3D strings (CL, EC etc). Is there any way I can make a road design that ties in to those strings (cross fall might change at some chainage, road width may vary but these are reflected in the strings) and export it to SCS900? I have tried looking for such videos but I could not find anything Thank you!
@SitechCS8 жыл бұрын
+Mihai Nita, The data in this sample video is very much like the data that you would see from a Moss Genio file. Once you have imported the data, isolate and select the 3D strings that define the road and simply use the "Create Surface" command from the "Surface" menu ribbon. Alignments included in Genio files are typically recognised immediately, but if you only get Genio 6D Strings, you can use the command "Create Alignment from Genio 6D String". This command can be found by clicking the drop down arrow attached to the "Create Alignment" command on the "Corridor" menu ribbon. Once you have the surface and alignment, you can apply the tips suggested in this video to improve the quality of your surface. If you have trouble locating any of the menus, use "Set Menu Layout" from the "Project" menu ribbon and load the "All Commands" menu layout. Rob
@gavinjones939 жыл бұрын
how do you model the bridge
@SitechCS9 жыл бұрын
Gavin Jones Business Centre - HCE is primarily surface based, though you can generate setout points and strings for structures. However to model a complete bridge, including precast components, conduits, reinforcement, formwork, etc, check out Tekla. You can watch a video highlighting the features here: kzbin.info/www/bejne/gnmcZH-we9qraMk. If you would like more information on this product, feel free to contact our team at BuildingPoint: www.tekla.com/contact/offices-and-resellers/buildingpoint-pty-ltd.