I'm considering the M10. How do you like it? And, where do you use it?
@alper888883 ай бұрын
Hi How do you see the drum, air, and gas settings on the artisan?
@jhamm153 ай бұрын
On the left side of the screen there are slider controls for drum, air and heat.
@LivingTheLifeRetired4 ай бұрын
This was an excellent overall video. I picked up a couple of pointers. I like the alarm for the SV slider. I’ve forgotten more than once to change that.
@LivingTheLifeRetired4 ай бұрын
The new M1s come with dual cooling fans and two burners.
@fromtheflightdeck2524 ай бұрын
Thanks, I need 400g so went with Kaleido M2, now on my channel ebikeCNX7239 at YT
@jackmangan23115 ай бұрын
What amp circuit are you running this on?
@nianniann-fw7nh5 ай бұрын
Hello, I am unable to contact you on the forum where you are selling this device. I would like to purchase this one
@johnwiencek6 ай бұрын
I just received my M1. I find your videos insightful on the use of Artisan, which I know a little bit about myself. I think you posted some of your settings over on the FaceBook page for Kaleido. How long does it take to cool down below 50 C? I did an initial run and then it took like 30-40 minutes to cool. I found that opening the bean drop chute made it drop in temperature faster ... but that was after 20 minutes of a slow decline. Are your dogs Yorkies? They are so cute. We have one and love him.
@fromtheflightdeck2524 ай бұрын
M2 is much quicker, but it's got 2 cooling fans, my channel shows it at ebikecnx7239
@HY_main7 ай бұрын
Nice Artisan demo video. I try to connect the roast manual mockup equipment with Artisan software with modbus potocol and read/write data form thermal gauage, fan, heater and so on.
@dearcoffee857 ай бұрын
Would you say you’re pretty happy with M1
@Testenginemotors7 ай бұрын
Me encanta esa tostadora de café soy fanático de la torrefaccion
@Testenginemotors7 ай бұрын
Hola te felicito de que país eres ? Yo soy de Venezuela
@TheCaptainsCoffee8 ай бұрын
That is WILD! Thanks for sharing! Did you use RDT on either of the 2 samples?
@Mzedith8 ай бұрын
I did not RDT for either samples. The nice thing about the beam is you don’t need RDT
@onTOPtheROCK9 ай бұрын
this board is directly from Kaleido?
@dongjoobae382210 ай бұрын
Where do you sell the motherboard?
@Mzedith10 ай бұрын
are you in the US? please contact kaleidoroasters.com/, they should be able to help you
@namangoyal1273 Жыл бұрын
So aee you basically replaying a previous roast profile automatically, so that it changes the settings of the roaster based on the bean temp targets that you had set?
@jestonhopper5137 Жыл бұрын
looking at upgrading to this roaster. Does this roaster plug into a standard outlet or does it need a dedicated 20 amp circuit. thanks for the video well done.
@Mzedith Жыл бұрын
The roaster needs a dedicated 20-amp circuit. with nothing else plugged into it while using, or you will pop the breaker
@LivingTheLifeRetired4 ай бұрын
That was a good video. I have a new M1, dual. It works well but I’m new to roasting. I have trouble keeping my ROR declining near the end as I am usually out of steam to get my desired development time and ending temp. Some people say that the probe temperature reads at least 10C behind the actual temp, meaning if my probe says it’s 200C the real temp would be 210. Any experience with that? It does seem that my beans hit first crack earlier that what maybe they are supposed to.
@thatdavidhuynh Жыл бұрын
Why is the roast longer when you start with a higher charge temperature as mention at 8:35?
@raymartin3527 Жыл бұрын
Thanks for putting up the video.
@Kanointhejungle Жыл бұрын
Trial by fire ...In my M10 if I started at 80% I will cremate the Ethiopian in less than 3 min... (450g 180 charge) Maybe 220V as opposed to 110V ?
@sh4dali Жыл бұрын
Thanks for the video. I am roasting on Gene Cafe and considering upgrading. What made you go with M10 instead of others? Does it do light roast well? Meain beans I roast is Ethiopean, which is hard to do with Gene. Thanks!
@richardcullip8468 Жыл бұрын
What a journey thru a variety of roasters. I assume that you aren't just roasting for yourself as you now have found a roaster that allows you to roast some volume.
@Mzedith Жыл бұрын
I did get a roaster that is too big for me, so i roast for friends and family
@TheCaptainsCoffee Жыл бұрын
Wow Edith, you've tested more roasters than me now! Awesome video, keep it up!
@sxmxdrifter Жыл бұрын
Very good E 😊
@Mzedith Жыл бұрын
Thanks 😄
@TheCaptainsCoffee Жыл бұрын
Great vid, Edith! Keep em comin' ☺
@portakeeper Жыл бұрын
great. video!
@Kanointhejungle Жыл бұрын
Nice video and audio quality... First one I didn't have to struggle to understand. Hope to see you do more roasts. Thanks
@Mzedith Жыл бұрын
thank you so much. Going to try and put together an Eithopia roast the next time
@sxmxdrifter Жыл бұрын
Nice F’n Job E 👊🏼
@scottOlsonsoulson Жыл бұрын
Great demo video about using the Kaleido Sniper M10 roaster and showing a nicely controlled roast