Пікірлер
@echohousepaintingnewton4331 3 күн бұрын
Great job
@KP-kz4os Ай бұрын
Mercedes charged me $5,947.08. Parts (2,635.08), labor (3,312.00)
@ThreeBizz Ай бұрын
@@KP-kz4os probably they changed the gear only, or in your area dealers are still honest with customers. In our case the client came with an estimate of 10k ))
@adiskevric7826 2 ай бұрын
Hey man. When you installed the new camshafts and was timing the engine again, did you just use the timing tool, and torque everything? or did you have to move the TDC back a little to tighten down the camshaft adjusters? I heard some people say you have to move the crank back a few degrees when tightening the camshaft adjusters because they won't be in time properly.
@BC_nopowder 3 ай бұрын
How much do you charge for job like this ?
@ThreeBizz 3 ай бұрын
@@BC_nopowder usually is from 4k to 6k at the dealership they charge around 10-11k )))
@BC_nopowder 3 ай бұрын
How much do you charge for job like this ?
@jackb2676 3 ай бұрын
hi, where is the location of the mass air flow sensor?
@dcasteaux9181 4 ай бұрын
These timing disks are known to move on other Mercedes engines including the V6 and V8. I welded my ones to the camshaft to stop this happening to me.
@algis3207 4 ай бұрын
Hello! Thanks for a very informative video! How long will it take for the discs to shift again, or did you already put welded ones on?
@Zharsergey 4 ай бұрын
What's the labour time for a job like this? Specifically the water pump/thermostat.
@ThreeBizz 4 ай бұрын
Water pump it is easy, thermostat is around 5 hours if you do it right, i see shops do in 3 hours and in a year leaks again :)))
@bmwlane8834 5 ай бұрын
After seeing this engine.....I love my BMW B48 4 cyc. engine even more!
@ThreeBizz 4 ай бұрын
hahahah, B48 have problems too :)))
@maverick_da1735 Ай бұрын
Worst lmao
@ThreeBizz Ай бұрын
@@maverick_da1735 hahahahha 😂😂😂
@bmwlane8834 5 ай бұрын
It should be tack welded from the factory!
@keithexum7312 6 ай бұрын
Good job 👍🏻
@rickardobrooks5032 6 ай бұрын
Did the a/c start working after replacing the solenoid on the compressor?
@ThreeBizz 4 ай бұрын
That was the Solenoid for Camshaft Adjuster
@roro85600 8 ай бұрын
P001685 C63S
@tyregalaxy28 8 ай бұрын
I need to replace my injector on cylinder 2 do i have to drain the coolant beforeb taken out supercharger and what gaskets do you recommend replacing once i remove supercharger
@ThreeBizz 4 ай бұрын
Yes , you have to replace gaskets too, but do the carbon cleaning too.
@katrachito10 8 ай бұрын
Hello Threebizz, thanks you for you video, is so helpful 🙏
@MohammadMostafa-z3y 10 ай бұрын
😮
@suryaprihadi2258 10 ай бұрын
Camshaft tone ring shifted. Is there an alignment marking on the camsaft to tone wheel? M276 engine some, not alll have alignment mark. Pressed in tone wheel, no spot welding at all to secure tone wheel, so sad. Thanks for the video, nice🎉
@ThreeBizz 10 ай бұрын
So there is not an alignment mark, so it is almost impossible to do some spot welding. is possible if you have a good one there in person and make your own marks and do some spot welding.
@suryaprihadi2258 10 ай бұрын
@@ThreeBizz ok noted, thank you
@ibragimgurbanismailov9090 4 ай бұрын
@@ThreeBizz Where did you go, why did you stop filming?
@echohousepaintingnewton4331 11 ай бұрын
🔥