HyperFlite Drones

Пікірлер

@kilkennyvfx 22 сағат бұрын

Just watched this tutorial and now have a working drone! Thank you kind sir!

@beautifulhymnalmusic8289 Ай бұрын

I have two Phantom 4 batteries that need to reset, do you still do them? Sent e-mail to you but properly went to your junk mail.

@frankdegerth Ай бұрын

why are you not using the reset button on the battery? just jumper the reset button and the battery minus.

@HyperFliteDrones 4 күн бұрын

It will not work.

@janihook686 Ай бұрын

Thanks for this video! I had a broken rear arm rotating axis part. Ordered new one from Ebay and I was able to replace it by myself because of this video 👍👍👍 Thanks once again 🙌

@HyperFliteDrones 4 күн бұрын

Great to hear!

@richardlong1567 Ай бұрын

Fantastic explanation - but the music isn't necessary and so repetitive! Thanks again.

@bagiamin5289 2 ай бұрын

thanks for your educate vedio - what is module of programmer , used here

@MrHunglo123 3 ай бұрын

hi can you fix my drone battery ?

@Yayaytytyyty 3 ай бұрын

I guess I need to buy a new battery

@tom.b897 3 ай бұрын

Thanks for the video. My drone has a problem with the horizon. As the altitude increases, the horizon becomes slanted. I have a video of it here 6gTjPYdv9RM What is the reason for this, what is the cause?

@HyperFliteDrones 4 күн бұрын

Damaged motor or cable.

@brucesabatoni3410 4 ай бұрын

Do you still offer this service? Do you work on phantom 3 batteries?

@xxCBOxx 3 ай бұрын

I Would like to know too as I need 2 repairing

@HyperFliteDrones 4 күн бұрын

I do not service phantom 3 batteries

@favourjohnson1718 4 ай бұрын

how can i sip my battery to you from Nigeria

@coacharchierabanz2488 4 ай бұрын

Hello sir ,where we can get that module box ?

@user-np6bv7to1g 5 ай бұрын

Hi my gimble is straight at startup than goes to left and gets a gimbal motor error, do you think it’s a bad cable? 27:29

@HyperFliteDrones 4 күн бұрын

Most likely an issue with a gimbal motor.

@noiamdnicklaus 6 ай бұрын

What program do you use to calibrate on the computer?

@julioaces1424 6 ай бұрын

Hello, does the MSP430 controller (EV2400 mini) work?

@HyperFliteDrones 4 күн бұрын

I do not know.

@wild_n_3 7 ай бұрын

What do you do if very first 2 screws rusty and thread is gone any other techniques we can apply ?

@HyperFliteDrones 4 күн бұрын

You need a small grinder to turn them into a flat head which is easier to unscrew. You can also warm up the screw with a solder iron.

@udi. 8 ай бұрын

Really helped me! great tutorial! thanks :)

@MrSKB69 9 ай бұрын

Fook that, am gonna stick a nail through both of mine LOL

@wildirishladdavy7965 9 ай бұрын

What is the glue you used ?

@MyAdventureHat Ай бұрын

Any answer on this?

@kilkennyvfx 4 күн бұрын

@@MyAdventureHat loctite super glue gel control works just the same

@MyAdventureHat 3 күн бұрын

@@kilkennyvfx Thanks!

@friartuckfriartuck 9 ай бұрын

maraming salamat po!!! MABUHAY!!!

@Glenn-Reviews 10 ай бұрын

Hi. Fantastic video. Thanks to you I was able to repair my drone that had a broken arm axel. Instead of a big bill it cost me % euros for the part!!! Thanks so much. Good job

@danieladams3858 10 ай бұрын

Hello i have two phantom 3 batteries never use not even first charge any way you can save them

@thomasgilbert6924 10 ай бұрын

Can I use st link or cjmcu 2112 adapter

@user-vy5mu3dk4w 11 ай бұрын

How can I charge dead battery without taking it apart also what pins can I check the voltage on from the back of the battery

@HyperFliteDrones 4 күн бұрын

You will not get any voltage to the pins.

@florinberechet6375 11 ай бұрын

I have a problem with my Mavic 2 Zoom, some jitter on yaw axis appear from time to time(no error message for the motor though). You say something about some bad batch of yaw motors... Could this be the cause în my case? I bought the drone S-H, the seller swored it did not crash it, there were no signs but I couldn't see the problem with the yaw motor then but when it was too late to return it. The gimbal is mechanically fine, end points are ok, no springiness, no bendings...I now have to decide between buying a complete gimbal or just the yaw motor. Any idea, please?

@user-rj8vt2wk3v 11 ай бұрын

Quiero la Información donde mandar mi batería te hi el mismo problema

@YL-mc9oz 11 ай бұрын

Hello, I really enjoyed the video and your explanation! I wanted to ask if you happen to know what the white glue that DJI uses is? (On the wires of the drone so they don't move and also in the battery you can see it above) Thanks

@kinginamez4055 Жыл бұрын

Its better to Buy a nrw one.

@jaredbarnett7756 Жыл бұрын

Where can I find these parts? Like a replacement yaw motor?

@Menace.The.Dennis Жыл бұрын

Do you still service Phantom 4 batteries?

@thefouramigos4795 Жыл бұрын

My motor is seized it wasn’t spinning when I got it out of the bag, it won’t rotate freely but is receiving power. Also all of the lights are the exact same as yours.

@Pistache_y_Turron Жыл бұрын

Hello thanks for your video I am trying to balance a DJI Phantom 4 Dron smart battery. After watching your video got a Venom PRODUO charger. After opening the battery I found out that the conector or balancing lead of the battery to the BMS Board is a 5 pin JST SH 1.0mm and the 5 pin female conector of the Venom charger adaptor is a JST XH 2.5 mm. I am ready to make a custom conector male JST XH 2.5 mm to a female JST SH 1.0 mm, my only concern is the order of the cables. Can you help please? I just want to know wich pin in the 5 pin female JST XH Adaptor is the ground as I have 5 cables in my battery balancing lead, 4 reds and one black. Thanks for your help

@alejandroma2333 10 ай бұрын

Hola. ¿Pudiste solucionarlo? Tengo la misma duda.

@Pistache_y_Turron 10 ай бұрын

@@alejandroma2333 no, resulta que el conector no es el de 1.0 mm. Lo que le quedó perfectamente fue el Micro JST 1.25mm Pitch Male Female Wire Connector 1.25mm 5P JST Plug Jack Terminal Cable Connectors Length 15CM. Ya venían precrimpiados y seguí el mismo orden. Los compré en AliExpress y funcionó muy bien.