How much

Maybe they put a non fused disconnect for it because they already fed the sub panel with a GFCI circuit breaker at the main panel…. Which you can do

Put a connector on that romax

If it's a 20/30 split, a surge protector is needed.

Thanks for the info 👍

try $16000 now

Looks pretty safe

I use a little torch from 711 instead of worrying about carrying a heat gun and trying to find a source of power for it. You have to be a little careful but it works fine. Better in tight spaces than the heat gun too. Definitely good to heat them up when the barb underneath is plastic. I have had them break off. I just replaced a heater somebody broke the 3/4 barb off of the back. I think you can replace the manifold on the hot springs ones. This was a jacuzzi so it was broken. The heater had no ohms anyway and it’s kind of tricky to replace if you don’t know what you are doing. You pretty much have to pry that hose off w a flat blade or it’s not going to come off. Even if you heat it up. If you heat it and use the flat blade wiggle trick after you twist it and break it free it comes off in about a minute. For sensor wires I use uy telecom connectors. You don’t have to strip the wires and the connection is waterproof. Great for lights too. I just spliced a topside that a rat chewed w them. It had a connector like a cat 5 cable on an old bullfrog and it worked fine. They needed a pump too though so the fun never ends

My hot tub has a blinking red light. It tries to start when I turn on the breakers soon after I hear a click (relay) but then it shuts down. Seems like the small e5 style circ pump isn’t working, it’s hot and won’t move any water. Can this cause the tub to shut down immediately and is there a work around that puts the main jets in low mode to circulate the water without the e5 circ pump? I’ve done that on another brand tub but idk if changing any of jumpers 1-12 can remove the e5 and allow the big jets to do the circulating in a pinch.

Do you know how to change the led lights inside this or where to order them? Half of mine have turned red or off

What's the model number, please?

Hey how do the filters go in Tia

i have the 2004 prodigy. and i just changed the heater circuit board because it wasn't heating up. now it gets warm but the jets don't work, and every time i press the jet button, the D17 red light comes on. would u happen to know why the d17 light comes on when i press the jet or jet clean button???????? i have called 4 electricians to come take a look but no body knows what they are doing 😔

Can you tell me what year model this is

You mention both a red and green flashing light. Did I get that right or is it just the green light. I currently have a green flashing light after replacing the two red washers on the end cap of the heater. My circle pump seems to be doing its job, but after inspecting the heater it is obvious that it is not heating up. I am just wondering before hacking the switch, is there a way to make Sur ethat it is the flow switch and not a complete failure of the heater. thanks

where can i get the pillow set?

Where are you located? How can I contact you?

How to turn off summer mode? Tub not heating

Hi I’ve just purchased a Coleman spa by maax second hand of Facebook UK do you have any idea where I find the exact model number please x

Hello, I tried this, install the bypass pressure switch, and connected it all back together. Now the red light is no longer blinking but my green light is not on at all and the spa is still not heating any suggestions?

No. I’m sorry this is all wrong. You’re deleting the Ozone, the Mazzi, and creating so much more work for yourself. Just replace the original part. It cost the same if not less than the flow sensor, and you wouldn’t have to remove the lower control, the ozone, the mazzi, splice the wire, heat the flex pvc, glue the new flex. The fail rate on those flow sensors are just as bad, they are no better than the hot springs thermistor.

is this a store?

How would I figure out the flow switch needed for a Vanguard spa (2013)? I don't see anything online that specifies which switches to use for which spas.

I have a similar Tiger River Spa. Everything works except the heat. However, If I run it for a long time (multiple times a day on jets) eventually the water will get warm. What could be the problem? (All I have done was replaced the filter so far)

Where can I get that aftermarket pressure switch?

I need a control board

hi i am from Cyprus from where i can find the control panel like this on the video

I have mine installed but unfortunately the piece is fluttering but not making contact with the pole thing. Not sure how to correct that.

Um, why didn't he do all that before he installed the first end? He has the piece to measure against? I'd advice don't use the heat gun inside the cabinet.

Saved me a lot of money. Thank you

What year is this spa ? I purchased it a while back but cant find the jbl speakers that fit

What year is this ? Its same model i bought yo get parta ?

Congratulations on your channel, I am a fan of your videos, you are a professional and excellent instructor. I have a HotSpring Jetseeter. When I turn on the jets I hear repeated clicks on the relays. I left the jets on for about 5 to 10 minutes and they stopped working, I checked the voltage (120v) and it was fine, the next step I did was unplug the pump and check if it was working and really if it is ok... I wonder if this is a problem with the relay board or the main board 🤷🏻‍♂️.... I hope for your help

Is there a video of that particular tub to go from 110 to 220?

13:02 hey I have a leaking hot springs puls 2012 heater w salt water corrosion. Best to replace or repair ?

Opl

Hi

How do u convert from plug and play to 230

I tried using the aftermarket flow switch, only to learn the switch was defective and did not solve the problem. I spoke with a technician at Spa Depot in Olympia, WA and learned that all you really need to do is cut the wire from the pressure switch on the Watkins heater and splice the wires together from the Molex connector mounted on the mother board. This activates flow and allows the heater to operate properly. The flow switch in not needed. My hot tub heater is now working and regulating as it should.

I did exactly this, fitting the flow switch and the repair worked. Thank you for the video. Saved me some cash.

I have one like this and all indicator lights seem to work on cotrol panel and on the board but jets don't come on? Any ideas

Hi Hot tube cowboy, I have a water leakage on the opposite side from the endcap. Who could provide me with an solution? There was a frost damage on the endcap and I‘m afraid that the opposite side has also suffered. Thank you!

Can you tell me how to change element. I have this one from 2002. And now not heating everything is working just like you just described but water not getting hot or no green light. Red light is solid jets works I see the ripples in water

I seems strange that the first thing you noted was the lights....

I cannot find one video showing how to open up the front accessible door covers. Can you please explain to me how to remove the front covers so I could get into electrical components please?

@Hot Tub Cowboy - I have an old Watkins tub I'm trying to get running and the board is fried. Can I replace it with a 3rd party or some sort of aftermarket control board? Finding an IQ 2020 to replace it has been rough.

13:10 This fixed worked! Thank you ….

where can i buy the aftermarket pressure switch

Anyone know why the Jets and Clean function won’t come on after changing the Neat Relay Board? Was working prior to the change. So odd.

I can’t even figure out the head rests!!! Lord help me 😮