Someone please show this range tactifool proper pistol grip technique (push ,pull ) and stance. 👍👍
@chriseuripides278 Жыл бұрын
What’s the ribbon for?
@antoniocarrillo711 Жыл бұрын
Someone help this guy out
@MalaFama4 Жыл бұрын
😂💀
@mr_slugger9049 Жыл бұрын
No Mames! 🤣🤣🤣
@Stuartyh7 Жыл бұрын
Super video mate. Bike looks and sounds great! Where did you have the camera mounted?
@bedtimestories10652 жыл бұрын
Where you at? Must be a crazy road for that sign.
@drizzyfam38932 жыл бұрын
FM-337 Twisted Sisters, TX
@latenttweet2 жыл бұрын
Yeaaaaa buddy
@wllytibe33272 жыл бұрын
Hey bud, any chance i can ask you some questions about the grate and plate upgrade? Thanks
@drizzyfam38932 жыл бұрын
Go for it
@wllytibe33272 жыл бұрын
@@drizzyfam3893 I just installed the gp ride plate and grate, however they dont line up exactly, the grate is maybe a 1mm or 2 lower than the plate, is that normal? Did yours line up perfectly? Did you use sealant? Did you use any kind of pump seal kit to fill the cavities? Where there shims used? Thanks!
@drizzyfam38932 жыл бұрын
@@wllytibe3327 so if I’m reading correctly, your ride plate is slightly recessed. If that’s the case, it’s normal and reduces any drag that would occur at the seam. I just made sure my angle lines were not offset so that everything lined up center to the hull.
@drizzyfam38932 жыл бұрын
I also found that while the aggressive design of the intake grate performed very well in rough water, the stock grate in combination with extended ride plate was the fastest in calm water. I would actually swap them out depending on what body of water I’m headed to and expected condition.
@wllytibe33272 жыл бұрын
@@drizzyfam3893 was the 66, 67 mph u hit with the gp grate? If so, how much faster was it with stock grate n gp plate?
@alexandrafinelli3812 жыл бұрын
I’m late to see this video but can u hear the extreme will riding at High speeds?
@drizzyfam38932 жыл бұрын
If you’re cruising around at 35-45 mph then yes. At full throttle, you probably wouldn’t hear it if you had headphones on lol
@lhgarage70002 жыл бұрын
Ciao drizzy. intake grate e ride plade gp 2019 compatible vx 2020?
@drizzyfam38932 жыл бұрын
It should be compatible with all 2020 VX hulls considering that Yamaha includes this same package on the 2020 GP. But as with any mod, please do your research before buying it.
@richardechevarria58243 жыл бұрын
I did exactly what you did to your ski I have the same engine I have a 2018 vxr and when I started it the warning engine light and beeper sound came on and beeped about 20 times and then stops beeping but the light and the check engine are still flashing and I noticed it will not go in neutral it starts in F and won't go into neutral. Is there anybody else out there that's having this problem? Please help don't want to have to take it to the dealership.
@drizzyfam38933 жыл бұрын
Nothing I did would cause that to happen. I would check the throttle cables and throttle body itself. If you didn’t put it back together with the gaskets in place exactly the way you removed it, I assume that could cause some issues
@richardechevarria58243 жыл бұрын
@@drizzyfam3893 I ended up breaking it down again and putting in the ribbon delete because some people are saying it causes turbulence plus I thought it was the reason for the warning. The dealership said that it's possibly a sensor that I may have loosened but I checked everything and I don't see anything but it is now doing the same thing with the beeping and flashing warning and check engine but now it starts in neutral instead of forward and the reverse is working normal. Totally weird it seems to have fixed one thing but not the main thing. I was told to start the ski without starting it pressing the throttle two times then start it and it should clear the codes. He said to try it a few times if it doesn't work. Do you know if the code # is displayed on the dashboard so I know what the problem is? If not then I will need to get a diagnostic. Thanks for your help.
@drizzyfam38933 жыл бұрын
@@richardechevarria5824 It should display a code but since I don’t know what the issue is, I can’t say for sure. Something to note, the left and right throttle control forward, reverse, and neutral. When you said it was starting in forward, my mind immediately went to an issue with the cables connecting to the throttle body. A bad intake sensor would definitely cause issues but that doesn’t explain starting in forward
@drizzyfam38933 жыл бұрын
Also, make sure that the throttle body is installed correctly. On mine, the mechanical parts covered by a circular plastic cover were positioned to the right, looking at it from the rear of the craft.
@richardechevarria58243 жыл бұрын
@@drizzyfam3893 2018 VXR 1.8L Everything was installed correctly and I did what my mechanic told me to do which was to press the start button without starting it pressing the throttle twice let everything clear on the panel and then start it and lo and behold the warning and check engine light turned off. It never showed a code number on the panel. I guess now next is to put it in the water next weekend and enjoy. Thanks for your help and your response.
@SenorDennis3 жыл бұрын
Hey I know this guy! Haha I’m the blonde guy that almost bought this ski. I was looking up mods on the one I ended up buying and came across your videos. That thing hauls!!
@drizzyfam38933 жыл бұрын
Give me shout if you want any advice. I’m happy to help!
@buddie6234 жыл бұрын
Really good video I just got this bike as a addition to my 17 kawasaki ultra and Sea-doo gxt 155. Thanks for posting again great job
@santanamauro76304 жыл бұрын
Does it fit on 2020 VXHO model?
@drizzyfam38934 жыл бұрын
I’m not sure on that one but it seems probable. I don’t believe they changed anything on the hull but please do your research before spending money.
@mj23bama4 жыл бұрын
You just sold me on it thanks. I’ve been looking at the extreme for my Seadoo
@drizzyfam38934 жыл бұрын
Good deal! One thing to note, it will put some wear on your handle bar pads after several uses. My thought is I can replace the pads later on if I want but it’s not that bad. Still using this set up to this day!
@jaylee34694 жыл бұрын
Hey drizzy can you give me an email when you get a chance at [email protected] ... I have. Few questions for you man thanks
@Markie_.0204 жыл бұрын
Wher can i find the aluminium pipe 45 agree
@drizzyfam38934 жыл бұрын
Markie Zorro here’s one from Amazon. OD 3.5" (89mm), Leg Length 4" (100mm), 45 Degree Bend Elbow 3.5 Inch 6061 Aluminum Pipe Tube Intercooler Pipe High Class Brushed Treatment Tight Radius Air Intake Tube www.amazon.com/dp/B07WCSLPWD/ref=cm_sw_r_cp_api_i_TQimFb1RN3C2E
@Markie_.0204 жыл бұрын
Drizzy Fam thank you
@andrzle4 жыл бұрын
For some reason mine won’t rev past 6500rpm and it leans really hard to the left. Do you know why that might be?
@drizzyfam38934 жыл бұрын
Andre Appert I’m certainly no mechanical expert but it sounds like something is dragging. Have you inspected the hull, ride plate, and intake grate? I would start there
@drizzyfam38934 жыл бұрын
Andre Appert if everything checks out there, I would check air filter first to make sure the engine is breathing, though that wouldn’t explain the leaning left. Also check the inside of the hull while running in water to make sure there’s not an exhaust leak. That would pump water into the hull making it unstable and causing it to bog. That’s happened to me on an old Kawasaki in the past
@andrzle4 жыл бұрын
Wow thank you so much for the reply! So my ski was brand new out of the box. I followed all of the break in procedures as per the manual never beached. But after break in period I pinned it wide open throttle and it revs to exactly 6500. Thought that was odd and it looks like yours revs right up to 7500. And I just wanted to clarify that tours doesn’t noticeably lean left? Even when the engine is off and floating in the water, my ski sits about 2 inches lower to the left in the water. Starting to think I have a defective unit for sure.
@drizzyfam38934 жыл бұрын
Andre Appert in that case, it definitely needs to go back to the dealer to be looked at. The engine should rev out at around 7400 stock and leaning left is not normal at all
@andrzle4 жыл бұрын
Drizzy Fam thank you so much for the help. I wanted to get some other opinions. I already took it to the shop today. I shouldn’t be that dissatisfied with a literally brand new jet ski. I’m just hoping they don’t feed me BS about it being completely normal. Thanks again!
@SupaNami4 жыл бұрын
Shoulda spent that money on a dental plan!
@drizzyfam38934 жыл бұрын
SupaNami it’s easy to talk from a distance. I’m sure you’re perfect and great
@waylinvanhalen4 жыл бұрын
Ultra 150s did 81
@drizzyfam38934 жыл бұрын
Funny enough, I raced a stock 150 on somewhat choppy water pulled away from it. I assume if you modify it enough, you could get 80’s
@jasonbourne34484 жыл бұрын
Noticed you motified the chrome and center piece right in front of your knee when you're on board. Did you paint it? It looks good!
@drizzyfam38934 жыл бұрын
Jason Bourne yes, I sanded and painted the chrome colors plastics and applied red vinyl to the center black colored plastic. I’m assuming you watched my other video where these changes were done.
@drizzyfam38934 жыл бұрын
Jason Bourne my biggest problem is I can never leave anything alone lol
@jasonbourne34484 жыл бұрын
It looks good! I have the same problem...I can't leave well enough alone. I have a 2016 vx ho, however I've changed the decals to a 2017 and replaced the seat with a custom hydroturf. Done the intake grate, ride plate, candoo gps speedo, ribbon delete. Debating on your exhaust modification and a different air filter.
@drizzyfam38934 жыл бұрын
Jason Bourne just an FYI on the exhaust mod. It’s cheap and easy to do but I’ve since put the stock exhaust back in. It was just a little too boomy at lower rpm’s. But if you don’t like it, you can always easily reverse
@jasonbourne34484 жыл бұрын
@@drizzyfam3893 that's my worry too. That it would be too loud for my liking...I am not one of these young bucks.
@carloschaqui82344 жыл бұрын
Just came across your video , I see it was posted about a year ago. Good mods , but you can’t really go by what the speedometer reads. I have a 2019 VXR with the same mods and by the speedo at full throttle it has read 84mph (lol). Best way to see your top speed is by using GPS. From 84 to what the speedo was reading GPS read 61mph and it was on two different model GPS.
@drizzyfam38934 жыл бұрын
Carlos Chaqui Agreed. I was simply stating the difference between before the mods and after. I’ve since then added an intake grate and ride plate. GPS’d 65 mph using an app. Not the most accurate but I have nothing to gain from knowing exact speed. I can tell you it’s faster and that’s all I was looking for. Thanks for the comment!
@motorsoft74764 жыл бұрын
I have a 71mph GPS at VXR 2015 on lake and 73 on river)
@Dannnyperezz3 жыл бұрын
@@motorsoft7476 what do you have done to the vxr?
@icecanator3 жыл бұрын
@@motorsoft7476 What have you done?
@AndTodaysProjectIs4 жыл бұрын
Are you guys using a GPS speed tracker to claim these speeds or the Yamaha Dream-o-meter? That little junk paddlewheel on the ride plate is notorious for being incorrect. I would be curious what GPS speeds you are hitting though to compare that to stock.
@drizzyfam38934 жыл бұрын
Robert Warren thanks for the response. The point of the video was not necessarily the actual speed but the difference between before and after the mod. I later gps’d the ski at 67 mph but that was after adding a ride plate and grate. Not the fastest ski on the lake but plenty for what I’m doing
@AndTodaysProjectIs4 жыл бұрын
@@drizzyfam3893 Naw, I get it...and glad you posted the mods regardless of the results. Just would have been great to have a known GPS speed before and then a GPS speed after if similar conditions, rider weight, fuel load etc were involved. I know that from one ride to the next that dream-o-meter will log different speeds depending on its mood but in order to get reasonably accurate results a person has to go to such great lengths to make sure conditions are perfect (no wind, flat water, poo before going out to make sure you weigh the same as last time ...errrr...maybe that one is overkill?). PITA but I'm sure you found some HP and speed somewhere in those mods regardless so its all cool. Did you throw a toploader intake grate onto it? Those are pretty legit for feeding the pump more evenly anyway. Happy trails.
@drizzyfam38934 жыл бұрын
Robert Warren yes, I purchased the 2019 GP1800 handling package. The hookup in chop is the biggest benefit but overall effected the performance positively. Again, I’m not racing or getting sponsored by anyone. I’m just a personal owner looking for a little more performance on an economical budget. I suspect there’s a few more like me out there
@justemilyme99374 жыл бұрын
Wow I am for sure to try this thanks for the helpful tip! XD
@kontikinomads67505 жыл бұрын
My 2019 does that speed with the ribbon, and wont explode when it does backfire, RIP bro
@drizzyfam38935 жыл бұрын
KonTiki Nomads good for you. It takes far more going wrong than a backfire and no ribbon for it to explode. Ribbon delete is very common and there’s no documented explosions due to a lack of the ribbon that I’m aware of. And yes, I researched before removing
@Frank_tha_tank15 жыл бұрын
Good review !!!
@sniper19585 жыл бұрын
I noticed you are in Texas. What part? I'm in North Tx. Dallas.
@drizzyfam38935 жыл бұрын
sniper1958 I’m in Houston. I know the Dallas area has a lot of lakes. I’ll have to make a weekend trip up there soon.
@sniper19585 жыл бұрын
@@drizzyfam3893 If you do let me know. Just purchased a VX cruiser perhaps we can get together. [email protected]
@drizzyfam38935 жыл бұрын
sniper1958 will do!
@dulogi5 жыл бұрын
Hey very good video! I have a 2018 vx cruiser would the 90 degree elbow fit properly if I can buy 3.5 " to 3.0 " ? I know you did say 3.5 to 3.25, would work better but I haven't find it. any advise is well appreciated. Thanks. Duv.
@drizzyfam38935 жыл бұрын
LEAH AND AMY LOPEZ not sure if the 3” side would fit. I was able to tighten down the 3.5 perfectly so I wouldn’t sweat it too much if you can’t find one
@dulogi5 жыл бұрын
@@drizzyfam3893 good enough.... thanks !
@triplenickle69955 жыл бұрын
Hey how about posting links to the parts you bought from Amazon? Also you will get some turbulence in the area where you removed the ribbon delete since nothing was installed in the ribbon and seal area. Good video man.
@drizzyfam38935 жыл бұрын
Don Juan I’ll have to look up the parts later and post them. As far as turbulence, what understand is that it’s a positive turbulence and does not negatively effect the air flow at the rate it will be traveling. I think the ring is maybe beneficial in supercharged engines and racing intake mods. For a stock naturally aspirated engine, you’re likely wasting money
@drizzyfam38935 жыл бұрын
Don Juan Ronteix 4-Ply 90 Degree Elbow Coupler ID 3-1/2 Inch Radiator Silicone Hose (3.5''(89MM), BLACK) www.amazon.com/dp/B075SV6437/ref=cm_sw_r_cp_api_i_dVgtDbSNTXT8S
These are the exact parts I ordered. A couple notes: you may want to search for a 3.5 x 3.25 elbow because there’s a little play on the water box connection. Nothing a hose clamp doesn’t fix. And the 45 aluminum pipe would be better in a 12” length but appears to be more expensive in shorter lengths. I cut mine down very easily
@triplenickle69955 жыл бұрын
When I removed my intake and ride plate to add anti-seize I saw that the big cavities on the sides of the ride plate were holding water.. salt water even and it had a lil corrosion. I sand blasted off all the corrosion on my plate and filled the cavities up with silicone so water would not get in, stand, sit and start corroding. You can see on your stock plate how the cavities have turned color from water standing in them. You might want to do the same on your Riva plate. I applied anti-seize to a bunch of bolts below the water line. That salt water corrosion starts the first time its dipped on the water, and never stops even with flushing and washing. Good video btw. So how much speed did you gain with just the ribbon delete??? and how much more with the ride plate and intake??
@drizzyfam38935 жыл бұрын
Don Juan I noticed the same cavities but I mostly ride in fresh so I’m not as concerned. But great idea! Stock I was running 59-60 mph, ribbon delete & exhaust 63-64, ride plate 66-67. I only have around $200 invested in upgrades so needless to say, I’m very happy with the results at that price. A little elbow grease can save you a lot of $$$
@triplenickle69955 жыл бұрын
@@drizzyfam3893 only 200? I need to get my parts from your supplier. I saw on riva just the ribbon delete and flame arrestor was 259.00 You got a good deal on the parts.
@drizzyfam38935 жыл бұрын
Don Juan no riva parts needed. Check out my page first video of mods. Also, the handling package link is in the description. It’s the stock grate and plate for 2019 gp1800. Bolts right on newer vx hulls. You don’t have to get the grate, that’s more for better hookup in rough water. The plate alone will get you the speed and better handling
@drizzyfam38935 жыл бұрын
kzbin.info/www/bejne/fXmuaJ6lntdpppI
@drizzyfam38935 жыл бұрын
Update: I ran it with gps today and topped out at 66.5 mph. A picture is posted in YAMAHA WaveRunners OWNERS on Facebook
@jaylee34694 жыл бұрын
I bought the same one you did off greenhulk. However the Riva one comes with reinforcement brackets . Should I buy these brackets for the green hulk one . Does your grate and plates need any reinforcement . Or you never had a problem ? Thank bro I loved your videos . I’m doing all the stuff to my ski now that you did except the ribbon . Hoping to get another 5-7 mph out of everything but the ribbon
@jaylee34694 жыл бұрын
Also do you recommend a new solas impeller or no
@drizzyfam38934 жыл бұрын
Jay Lee I didn’t get the reinforcements and haven’t had any issues. I will tell you that I’ve since then put the stock grate back on with GP ride plate and I get a little more top end. If I’m headed out to a choppy lake, I’ll throw the GP grate back on. It performs like a champ in rough water
@drizzyfam38934 жыл бұрын
Jay Lee I haven’t upgraded the impeller yet so I couldn’t say. I would imaging you could get a little more top speed out of changing the pitch as long as you’re easily hitting your rev limit. There’s some give and take with impeller upgrades so do your research first before dumping money on one
@timshull595 жыл бұрын
Very nice, going to seal a deal on one of these in the morning!
@drizzyfam38935 жыл бұрын
Awesome, you won’t be disappointed! Or at least I wasn’t
@Drew-py8kg5 жыл бұрын
they sell a mount in that exact position for like $30 and you wont need that net
@drizzyfam38935 жыл бұрын
Drew, who’s they? If you have a link for that, please share it.
@Drew-py8kg5 жыл бұрын
@@drizzyfam3893 www.pwcmuscle.com/yamaha-speaker-bracket-for-gp1800-fx-vx-models.html My friend has it and it works very well
@jaylee34694 жыл бұрын
Drew what speaker does he have in that holder product you shared
@Drew-py8kg4 жыл бұрын
@@jaylee3469 Looks to me like its a jbl charge 3 or 4
@mj23bama4 жыл бұрын
Will it work on the Seadoo gti
@timshull595 жыл бұрын
Great looking ski, I have been considering this model.
@patrickmacnab97855 жыл бұрын
I have the same exact ski and I hit 68 with no modifications
@drizzyfam38935 жыл бұрын
Patrick Macnab on the trailer, on the way to the lake lol
@jeremyschmidt44495 жыл бұрын
@@drizzyfam3893 I have the same also except mine is a 2018. I only have 10hrs on it, completely stock. I have seen flashes of 68mph also, consistantly hit 67. I'm guessing these speedometer's are varying. I need to check it with GPS.
@drizzyfam38935 жыл бұрын
Jeremy Schmidt the speedos can vary in accuracy for sure. I ended up confirming with a gps. The point of this video is the performance upgrade whether the speedo is accurate or not. With additional mods (newer video) I’m hitting 66.5. I’ve confirmed this by gps (posted in Yamaha Waverunner Owners on FB)
@jaylee34694 жыл бұрын
Drizzy Fam lol can you explain a dude above saying same ski but stock goes 68? Mine is stock same as yours and goes 58 .. that’s why I’m doing everything your doing
@daso99772 жыл бұрын
no way this ski goes 68 stock.
@strong46475 жыл бұрын
Hey there. I have a 2016 vxr and want to save the money from the riva. Only thing I'm nervous about is the 45 degree pipe getting to hot. Have you ever noticed the engine bay being really hot?
@drizzyfam38935 жыл бұрын
SXS Vids hey. I’ve had no issues with the pipe getting hot. It’s a wet exhaust so it never really reaches high temps. In fact, the sun made my hull hotter than the pipe. It is however boomy sounding on the low end rpm’s. Since this video, I’ve change my opinion and reinstalled my stock exhaust and then tried the tj exhaust mod. It’s not quite as loud as straight pipe. The best gain will be taking out the ribbon. Hope this helps
@drizzyfam38935 жыл бұрын
My next project, I’ll be installing a 2019 gp1800 ride plate which extends further than mine stock. They are also standard on 2019 vxr’s. I’ll post a video when I get that in
@strong46475 жыл бұрын
@@drizzyfam3893 how does that tj mod work? And did the ribbon delete today but havent tested it out yet.
@drizzyfam38935 жыл бұрын
SXS Vids first remove the plastic resonator from the main exhaust hose. Then remove the main hose. This is the large rubber u-shaped hose connected to the water box. You will then cut approximately 3” off of that hose that would otherwise protrude into the large plastic baffle. This part of the hose is opposite of the water box. It will make more sense once you remove the hose and see the extended part that can cause restricted exhaust flow. Then reinstall the main hose but do not install the resonator. Plug that hole with a 2” pvc plug. Make sure everything is clamped back into place using the original hose clamps. This mod will only cost you $2 for the pvc plug. The one I bought was threaded and fits snug.
@drizzyfam38935 жыл бұрын
Also, once you start taking the exhaust apart, you’ll see how the exhaust is dumped into a plastic baffle. That should answer your original question about heating up. It it generated high temperatures, they would not use that thin wall plastic
@saturnreturns6135 жыл бұрын
My speedo is pretty dead on with gps. My 2016 models (2) run right around 62 mph also. Lake is 900 feet above sea level fresh water.
@drizzyfam38935 жыл бұрын
Dual Fuel Coyote I used a gps recently and got the same results. Other than the speedo jumping around a bit, when it reads top speed it’s pretty accurate
@shuvelhead2335 жыл бұрын
I have a 2018 Vx cruiser ho. Was looking at different mods that won't effect my warranty. Top speed I've got on my lake is 65 on flat water. That's stock using the speedo. Plan on using a GPS to see how accurate speedo is. My question to you is, after the mod, would you do it again or just leave it stock?
@drizzyfam38935 жыл бұрын
shuvelhead233 hold that thought, I’m actually headed to water to test couple of changes to the mods. I’ll post results this evening with gps speedo
@drizzyfam38935 жыл бұрын
Check out this video: kzbin.info/www/bejne/gHnQipihltCfY9k
@tg17405 жыл бұрын
Thanks for the info! Planning the same for my 2019 VX Cruiser HO. Any other mods planned? My GF thinks I am crazy as it is wicked fast stock. 👌🏻
@drizzyfam38935 жыл бұрын
Only if you want to strap some music to it: kzbin.info/www/bejne/iYbGe6GXYpt2gsU
@duvallgroup2055 жыл бұрын
I love how genuine you are explaining this video! There’s nothing like good solid people that get strait to the point without sugar coating anything. I do have a question for you.... I have this exact same ski and absolutely love it. On that 90 degree silicone you mentioned 3.5” OD. I can’t seem to find that particular one on Amazon although I did find a 3.5” “ID”. Is this perhaps what you were referring to? I just wanted to clarify.
@drizzyfam38935 жыл бұрын
Jared Nelson the silicone 90 is a 3.5” ID. I believe this the one I purchased from Amazon Ronteix 4-Ply 90 Degree Elbow Coupler ID 3-1/2 Inch Radiator Silicone Hose (3.5''(89MM), BLACK) www.amazon.com/dp/B075SV6437/ref=cm_sw_r_cp_api_i_CuK1CbTCBP0YA
@drizzyfam38935 жыл бұрын
The elbow was slightly loose on the water box connection but the hose clamp did secure it well. It would probably be a better fit if you can find a 3.5 to 3.25
@-Darren-5 жыл бұрын
Is this the stock speedometer? I just purchased 2 of these 2019 models and the stock wheel speedometer is very inaccurate. Tested mine with a gps speedometer and stock I have seen 63 MPH. I bet your speed is a little higher on a gps module.
@drizzyfam38935 жыл бұрын
Darren Cargain yes it’s stock and it bounces around quite a bit so I don’t think it’s accurate. I raced 2 Kawasaki supercharged ultras and held neck and neck with them. So I know I’m well above 60
@darbydalepta46555 жыл бұрын
I was thinking of buying one but thought it would go faster than that. My 05 vx deluxe runs 60mph on a smooth lake with a straight exhaust solas impeller and air filter
@drizzyfam38935 жыл бұрын
60 on gps or speedo? I noticed the speedos differ one from the next. I haven’t gps’d mine yet so not sure of actual speed. I can assure you that no vx deluxe on the lake can even try to keep up with me. Not bragging, I see them all the time and they are much slower than my ski
@oldguysrockon5 жыл бұрын
Reading your speed on the stock speedo or phone is a joke and is no way accurate.
@drizzyfam38935 жыл бұрын
Chuck Germany, my point was not the exact speed, but rather the difference from before the mod to after. Maybe I didn’t state that clearly enough.
@oldguysrockon5 жыл бұрын
Drizzy Fam Maybe you should mention the variables at any given time or place such as air temperature, humidity, rider weight, flat water or choppy, on a lake or river with a current. Posting speeds using unknowns is never an accurate thing. Especially to newbies that want to use screwdrivers to pry the ribbon out. Good job tho on the video. At least you are honest.
@ADD_503 жыл бұрын
Hey Chuck, make your own video.
@oldguysrockon3 жыл бұрын
@@ADD_50 Actually i did make my own video. But it was eleven years ago using all of the accurate resources i mentioned to you TWO years ago. Keep up the good work and good luck learning.
@ADD_503 жыл бұрын
@@oldguysrockon must of been in the top 2,987,678,329,000. Missed it.
@d2king9416 жыл бұрын
My 2012 vx cruiser goes 61 mph
@drizzyfam38936 жыл бұрын
D2 King nice! It’s an ho 1.8L correct?
@X862go6 жыл бұрын
Great job
@drizzyfam38936 жыл бұрын
William Wood, thanks!
@davidbenson25086 жыл бұрын
Thanks! Great information! 8 more mph for less than 50 dollars.
@RanmaP6 жыл бұрын
Hi, is this stock or with mods? How many hours did you have on your waverunner? Looks like you had a full tank or near full is that right?
@drizzyfam38936 жыл бұрын
Around 25 hrs. See the other video on my channel. I did a ribbon delete and free flow exhaust for less than $50. Gas tank was full. This ski actually hit 66 mph on flat water with 1 rider.
@RanmaP6 жыл бұрын
Thanks for the reply. Did you ever tested max speed when you were stock? I have a stock 2018 VX Crusier HO but I only get 52 mph max on water that's like glass.
@drizzyfam38936 жыл бұрын
Phi Ngo stock was 60 mph max before mods
@drizzyfam38936 жыл бұрын
Phi Ngo try running 93 octane and take out the intake ribbon if you do nothing else. It is very restrictive
@drizzyfam38936 жыл бұрын
One last thing, the speedo is junk on these. Yours may not be reading correctly
@drizzyfam38936 жыл бұрын
This ski hit 66 mph in calm water 2 days ago. I’d say that is a success!