"CAN YOU LIFT ME HIGHER"? 🎵🎶🎼. Damn shitty Nickol back, because of this video that damn song is stuck in my head and let me tell you you do not want a pickleback song stuck in your head 🥒 🔙
@TonyTheTruckGuyКүн бұрын
LOL!
@andersian1985Күн бұрын
Yea i orderd some off aliexpress same kind i had for my 16 escape hoping they work flawlessly in my 18 compass like they did in my escape
@collinperschon2183Күн бұрын
Thank you
@ColbyHutzell-ek4xgКүн бұрын
Yep, that thing is junk now... you have the f***in tube clamped in the vice snd start beating on the yoke...
@TonyTheTruckGuyКүн бұрын
And yet this very drive shaft has seen 325k miles. You can hold it in the vise without clamping and crimping it to death.
@ColbyHutzell-ek4xgКүн бұрын
@@TonyTheTruckGuy you beat on the yoke, there is no way that thing is still within minimum runout😂😂😂 that tubing is probably only 065 wall dom... no need to clamp it in the vice thats the cave man way of doing it.
@TonyTheTruckGuyКүн бұрын
@@ColbyHutzell-ek4xg Well, I'm a caveman, so.
@hdwnzjurncusmnfkКүн бұрын
I thought I was at the club for a second!
@TonyTheTruckGuyКүн бұрын
Spin that beat! 😂
@deadpossum1002 күн бұрын
I'm going to use a table saw as my work bench from here on out.
@TonyTheTruckGuy2 күн бұрын
🤣🤣
@Randy-no5mi2 күн бұрын
What a joke. Why would ram do something so damn dumb? All for 2 small bulbs. 2 middle clips on mine wont budge. LEDS aren’t worth it to me.
@TonyTheTruckGuy2 күн бұрын
Some people have been able to do the front map lights just by removing the lens but you gotta use a needle nose and have some finesse. But they should just all be LED at this point.
@jamesjonsy2 күн бұрын
Word
@BobSmith-iz3hk3 күн бұрын
The R on the mount plates is for Rear not Right. That being said, I had to swap the front plate on the rear passenger side like you said!
@KingsForLife404 күн бұрын
Thanks for posting
@KIGHT34 күн бұрын
I have a 2006 so what u said in the video do the same. Thing
@TonyTheTruckGuy4 күн бұрын
Should be same steps
@ednaperez8595 күн бұрын
Hey i just put my led lights yesterday, and now one of my directional lights doesn’t work
@TonyTheTruckGuy5 күн бұрын
Double check you have the bulb installed correctly and in the right position. If issue persists, plug the old tail light back in so you know if it's a truck issue or an issue with the new lights.
@JEFFREYDUTTER5 күн бұрын
This video is the perfect exhaust video, exactly what I’m looking for, thanks!
@TonyTheTruckGuy5 күн бұрын
Thanks! Yeah there’s not too many videos on these. Glad it helped out 😃
@zzz7zzz96 күн бұрын
looks like you need to replace the rubber bottoms on your shoes now.
@TonyTheTruckGuy5 күн бұрын
😂😂
@lostinspacerobinson15276 күн бұрын
Excellent vid ! How long did it take to complete ? Rock on !
@TonyTheTruckGuy5 күн бұрын
Ohhhhh I can’t remember now it’s been a while and of course filming adds time and then I had to mess with that connector. Probably an hour or 2 if you have all the tools and don’t run into any issues.
@lostinspacerobinson15275 күн бұрын
@@TonyTheTruckGuy thanks for the reply, yea I just did this same job on a civic ( 05 ) and the design is ridiculous, took me about 3 plus hours with all the tools , the problem was that the sliding bracket for the alternator gets in the way of the actual lower alternator bolt , it's easier to just remove the whole bracket which is held on by 1 bolt the put the slider bracket bolt in then install, ( if you know what I mean ) whacky ass design if you ask me ! Cheers from Ohio ! 🍻
@TonyTheTruckGuy5 күн бұрын
@@lostinspacerobinson1527 Haha yeah, the design could definitely be better, and I remember that bracket being annoying. I'm sure you had to deal with a little Ohio rust as well haha. Glad you got it figured out, though!
@lostinspacerobinson15275 күн бұрын
@@TonyTheTruckGuy yep yep ! Good ole Ohio ! Ps , cool channel btw , I like your style ! Peace out ! 😁
@TonyTheTruckGuy5 күн бұрын
@@lostinspacerobinson1527 Thank you, take care!
@Diesel-powered6 күн бұрын
Nice thank you
@timtrowell10346 күн бұрын
Thanks !!!!!
@timtrowell10346 күн бұрын
Time to replace mine. I got stopped early this morning coming home from work. Had no idea they were even out. Only got 16 years out of them. 🤣🤣🤣
@josemarquez52936 күн бұрын
Thanks buddy
@user-wl8kz9vt4x7 күн бұрын
Great job!
@TonyTheTruckGuy6 күн бұрын
Thank you!
@nancytracey56897 күн бұрын
How about 2016 jeep compass. I turned key to on position. Pressed 3 times gas pedal. Turned off. Didnt work. Tried 2 more times, pedal became hard to press down. How long should I wait to try again
@TonyTheTruckGuy6 күн бұрын
Gas pedal should never get hard. You sure you’re not pressing the brake instead by accident?
@nancytracey56895 күн бұрын
@@TonyTheTruckGuy OH NO, I THINK I DID Will that hurt my car???
@TonyTheTruckGuy5 күн бұрын
@@nancytracey5689 No, it’s normal for the brake pedal to get hard after a few presses if the engine isn’t running.
@nancytracey56895 күн бұрын
@@TonyTheTruckGuy THANK YOU❤️🫣
@damndatstuff93417 күн бұрын
What kind of harness would i need to get? I have a 2001 Chevrolet Tahoe LS 2WD the only things I’ve done with the audio is door speakers and the factory subwoofer it has the same factory head unit you have
@TonyTheTruckGuy7 күн бұрын
I've got everything I used linked in the video description. If you think yours is different, you could always verify online at like Best Buy or Crutchfield by year/make/model.
@Greg-qd7ku7 күн бұрын
Both of them went out just changed them with 3057 they lights are still out :/ good video though
@TonyTheTruckGuy7 күн бұрын
If both went out at the same time then it’s probably the brake switch itself or a blown fuse
@Greg-qd7ku7 күн бұрын
@@TonyTheTruckGuy nvm I accidentally changed the reverse lights 😂 changed the middle one and it's fixed now thank you
@TonyTheTruckGuy7 күн бұрын
@@Greg-qd7ku HAHA! Well hey, can’t complain about that!
@ridrigoiscool1238 күн бұрын
I wasnt able to get my car to go into programming mode for the longest time and the whole time it just needed a new keyless entry receiver
@TonyTheTruckGuy7 күн бұрын
Sounds like a lot of people with that issue on these. Was that just some module inside the car?
@kylepoling3298 күн бұрын
Thanks for giving a thorough explanation! 😎👍
@TonyTheTruckGuy7 күн бұрын
Glad I could help!
@Fred2-1238 күн бұрын
Might as well buy another carburetor ($12-$15) when you buy the 125B. The #1 problem with these is a clogged carb--which is almost impossible to clean. Lots of youtube videos on fixing this problem and changing the carb.
@TonyTheTruckGuy8 күн бұрын
Hmm. I wonder if this is more prominent with people using gasoline with ethanol in it and being stored for long periods? I use 91 non-oxy to mix with my 2 cycle oil and I have not touched the carb or added any fuel stabilizer since I got it almost 4 years ago haha. Good to know a new carb is pretty cheap, though!
@Fred2-1238 күн бұрын
@@TonyTheTruckGuy I have always run ethanol-free gas & 2 stroke oil, that's all. It lasted 7 years on the original carb. You cannot get the last few drops of gas out, so when it sits over the winter that's when it gets clogged.
@TonyTheTruckGuy8 күн бұрын
@@Fred2-123 Yeah I haven't even drained mine each year haha, just run it low. 7 years isn't too terrible though.
@martymorris94429 күн бұрын
Coil pack plug you push the metal bit down not pull it off rookie 😂
@TonyTheTruckGuy9 күн бұрын
Is that why YOU are watching MY video? 🤡
@hood72719 күн бұрын
Dude! That was so quick and easy, great video, I wish you nothing but success and awesomeness in your life. Don't have to listen to the ding of stupidity anymore
@TonyTheTruckGuy9 күн бұрын
Lmao, glad I could help!
@DanDan-of8nv9 күн бұрын
Great video. Very informative. Though I’ve done it your way more than once, if you can’t get you hands in such tight spaces, I recommend taking the bumper cover off. I’ve done it on this model more than a half dozen times. The light housing access is so much better. And you won’t tear your hands up. There are instruction videos on You Tube.
@TonyTheTruckGuy9 күн бұрын
My stupid bumper is held on with the plastic rivets which is the only reason I didn’t go that route haha.
@rainxlv9 күн бұрын
What running boards are those? Factory or after market
@TonyTheTruckGuy9 күн бұрын
Mopar OEM cab length! I have an install video on them 😁
@rainxlv9 күн бұрын
Checking it out now thank you!
@diymislola129110 күн бұрын
Thanks 👍
@CarsandCoding10 күн бұрын
The battery is either the wrong type or installed backwards because the terminals should be closer to the engine. Installed this way, the hood prop rod can short out against the positive terminal.
@TonyTheTruckGuy10 күн бұрын
If you flipped the battery around, the ground cable would be on the opposite side as the ground post lol.
@CarsandCoding10 күн бұрын
@@TonyTheTruckGuy it’s the wrong battery.
@TonyTheTruckGuy10 күн бұрын
@@CarsandCoding Very possible. The car has been junked for a few years now, unfortunately, so no more worries 😂
@CarsandCoding10 күн бұрын
@@TonyTheTruckGuyjunked? Man, it had a brand new alternator… LOL! Good video though!
@TonyTheTruckGuy10 күн бұрын
@@CarsandCoding Yeah the girl that owned it got T-boned. Thank you!
@xxxmichaelxxx510 күн бұрын
Mine didn’t work I’ve tried like a hundred times idk why if anyone can help
@user-eo8kx1dk7f10 күн бұрын
Cool! Something else to fix. I had no idea these had this. I is have a 2001 Tahoe. I see I have the same deal. Thanks man. 😂
@user-eo8kx1dk7f10 күн бұрын
Does the 2001 Tahoe have this as well? I just unplugged the Onstar button. Wondering if there’s a filter like that in my Tahoe.
@TonyTheTruckGuy10 күн бұрын
There should be
@YGisG10 күн бұрын
Dude, the BIGGEST omission was that it is NOT worth attempting to remove those UCA bolts without dropping the strut. You MUST struggle with using a prybar to literally jam/ram them out using ONLY the wings of the bolts to do so because you have no ability to push from nut-side... not worth it!!!
@johnwinchester965411 күн бұрын
Easy to follow and simple. I wish I could see the fog light assembly. I purchased new fog light bezels and lights but not sure how to add them. My compass doesn’t have them.
@TonyTheTruckGuy10 күн бұрын
Ah yes that’s probably going to take some more work haha. Is it a factory kit, or aftermarket?
@charmainejay983512 күн бұрын
Thank you this working for me perfectly a while back. I'm currently having a problem getting my camry to enter programming mode. I know I'm doing it correctly as I've done it before and made it work. But my car won't even enter programming mode. Do you have any videos on something else I can check?
@TonyTheTruckGuy11 күн бұрын
Unfortunately this one and the key pairing video are the only ones I have on the Camry. I assume you got a new fob? Try reading the pinned and top comments to see if there’s any solution that may help. Some people have had to switch the buttons around on their new aftermarket fob to make it work correctly.
@andersian198512 күн бұрын
so i can use basic led bulbs that dosn't have a wire?
@TonyTheTruckGuy12 күн бұрын
I would make sure to get some that are specifically advertised for the Compass that offer error free operation like these but yeah
@joestanley415112 күн бұрын
Automotive design sucks and should include the mechanics in mind. Build these trucks were you have room to work on them. Don't lay a/c, wires and vacume tunes over the coils.
@TonyTheTruckGuy12 күн бұрын
The new stuff is 100X worse, sadly.
@patrickconroy872913 күн бұрын
Nice job!
@TonyTheTruckGuy12 күн бұрын
Thanks!
@nexus828913 күн бұрын
Thank you very much had the truck for two years and never did that
@TonyTheTruckGuy13 күн бұрын
Glad I could help!
@karlbuckles719213 күн бұрын
I never had a clue about these and I am having the same problem! Thank you!!
@TonyTheTruckGuy13 күн бұрын
Just for clarification, I did slightly misspeak on the years in the video. 2003-2013 trucks don't have them, so you'll only have them from 99-02.
@twinpauls893413 күн бұрын
Boss😎👑
@-ISynI-14 күн бұрын
Big L finding this trying to find someone who's replaced the upper ball joint and not the entire control arm.
@TonyTheTruckGuy14 күн бұрын
There’s probably a reason for that haha, I’d just do the whole thing. Not sure if the OEM arm is even serviceable to be honest. Plus, what are the odds that the control arm bushings could also use a refresh?
@teaganwright393311 күн бұрын
You’d have to grind it out, the factory control arm isn’t able to change out only the ball joint, I’m in the middle of doing it but I just spent the extra $60 for the whole control arm instead of trying to find a way to put in a new ball joint.
@Hotdaddy53614 күн бұрын
Ford don't build their engines anymore they buy the cheapest they can find..the modular engine for example..and their diesel sucks as well..
@TonyTheTruckGuy14 күн бұрын
The modular gas engines were probably the best engines they had TBH lol. They actually do make their own diesel now with the 6.7 Powerstroke from 2011-current. All others were made by International.
@williamthornton863214 күн бұрын
Ford is coming out with a new heated tail gate. Designed to keep hands and ass warm while pushing and sitting.
@TonyTheTruckGuy14 күн бұрын
That will come in extra handy in the cold northern months!
@Elveganonyc14 күн бұрын
Hi Tony, I just got this myself, and I was wondering the soap compartment that came with the machine i don't really know how to use it to clean my car, or I have to buy soap gun just like that and forget about the soap compartment that came with (^_^), thanks
@TonyTheTruckGuy14 күн бұрын
The soap compartment is to be used with dedicated pressure washer soap for jobs around the house. For a car, I’d recommend getting a foam cannon attachment with dedicated car soap for best results.
@Elveganonyc14 күн бұрын
@@TonyTheTruckGuy thanks so much for replying, you are the best !!
@TonyTheTruckGuy14 күн бұрын
@@Elveganonyc No problem! Enjoy the new pressure washer!
@cassiewilloughby352614 күн бұрын
Thanks so much!! I found that really helpful and easy to follow.
@TonyTheTruckGuy14 күн бұрын
Glad I could help!
@joenguyen827015 күн бұрын
Engine crap out cause the idiot who owns it doesn't change oil since being bought