A lot of editing but still good tutorial.

I appreciate this man you helped out a lot

i see these problems in my shop. also a lot of misuse

Hipa has a ton of very good parts for every small engine made.

Distanta dintre care puncte stabilește lungimea unei lame la o drujba ?

a dull chain can also make it smoke, it gets hot and burns up the bar oil

Just throw it away and buy new each year.

Good video there on winterize lawn equipment 👍

Impossible to see when it is jerking all over

A plastic straw works for a piston feeler.

I had such a hard time finding the instructions to clean my carburetor. This was perfect thank you so much. Help me out my generator started after one pool. It was puking gas before. I will buy your parts and a bridge if you have one to sell.

I traded a box of shells for an old ms290, the issue I’m having is that the chain will tighten on its own when running? After adjusting the chain I’ll move it to make sure it moves freely and then it’ll tighten up and get stuck as I’m trying to move it, it’ll free up again sometimes then tighten up. Any idea what this might be? I’ve installed a new chain sprocket, new bar and chain, new chain guides. I have a new tensioner coming in but the tensioner seems to work fine?

thanks for the video

No mention of a worn out crank? If the crank isn't spinning true anymore it will cause slack in the chain, no?

Thank you for your help

i've used my husqvarna 150BT over 50 hours, checked spark plug recently was about to change (i've had blower 3 seasons) and it still looked normal. Still operates fine too so I am thinking I will just keep using it next year.

can't find a ripping chain for my rancher 450, can you send link please???

That spark tester did not come with mine.

It's actually called a magneto not an ignition coil.

I have that exact saw and you can change the chain without removing the bar, I've done it many many times.

Very informative video, thank you so much.

Perfect! Only needed to watch it once and voila.....Fired right up...Thank You Sir

This is the CORRECT way to make this adjustment. Beware the folks who switch the valves, that is the exhaust on the bottom and intake on top. Stick to the Briggs recommendations.

I have a 04 light 18 in and a super chain on a 180c it’s a mean little saw

Nice looking cart. I'll be watching to see how the restoration goes. I too am restoring an old Bristers cart, and posting my progress on KZbin. @timelapselife.seanjree43 Hipa has also contacted me via comment section. I've responded, but haven't gotten a reply. Any suggestions? Ride safe! Keep filming!

Well made video

on my 017 the master controol switch has a thin spot when you push it just past full choke, it pops right out of the clip with no effort. are you sure the new ones arent like this?

What! I have to sharpen the chain!????😲

What if you seem to have too much compression and it won’t start what could be the problem?

Or you can just hold onto the spark plug with your fingers and then pull on the string to tell if it’s sparking but it’s not very comfortable

Can’t talk without vulgarity. Not a person that I would trust with 2 cents. Just talk.

Mine stalls sometimes in cuts. Just got it off Facebook marketplace but it turns right up.

Very good video

Good video, all useful information. Blue smoke due to burning extra oil, say from worn piston rings, or a scored cylinder does have one advantage though! It helps to keep the Mosquitoes away while you cut the grass! :)

It back fires when you try to start it

I have brand new ms 181 do you think it have easy start

You're pointing to the wrong screws.

Easier than I imagined it would be. Good time to replace the gasket too in meantime since both of mine have a small leak

sounds like it should be called a Coil Tester ;)

Thanks for your video! I was having fits trying to adjust the valves because of bad backfiring and a lack of starting. I kept thinking I was doing it wrong because no matter how perfect I thought it was I had a no start condition. Turns out that the flywheel key was sheared and the only way of figuring that out was by removing the cooling intake and mesh screen to check. You could clearly see the key-way in the crankshaft 1/4 turn past where the flywheel key-way was. Only a $6.00 part. I wasn't the original owner, and had no history of symptoms to help me figure it out

Great presentation, straight to the point, well produced and no annoying music! 👍

Just had the chain issue w the sprocket yesterday on ms170

Thanks!

Idiot blocking the measurements

the MS170-180 are trim saws Not Logging Saws If you want to Cut Medium sized Trees & logs buy a Bigger Saw like a MS 250 or bigger .

3:40 m/s tighting valve is too tight on 1st adjustment, i back off 1/8 turn or so on the adjustment nut to get a feel for the correct lash. How are you'll getting the fine adjustment when you first set valve lash & its too tight?

A lot of people complaining about your arm being in the way. People without x-ray vision need to pipe down and make sandwiches.

Good luck I've done this since I was 7 years old😂

Help,Help ! Can you tell me the model or number on this carburetor? I NEED A NEW ONE. I have been unable to find what I need and this video is the exact carb I need. My model mower is a 1998 Murray model#20406c8A with the Briggs 5.5 hp L Head engine Please help me.