Learned a lot thank you !

Perfect !! Thanks for posting this. I needed it.

The last time I replaced rotors and bearings I bought new rotor that have no outer race in them .Had to go to shop to have them press in the outer race . Inter and outer had to go together as pair so they last longer . Its been many years ago .bearings still good but rotor worn out . Now all new rotor come already press in outer race, no shop around doing that either

The white light is a cargo light, I believe.

Great video

See the latest Legion Act change by Congress in July 2019. All veterans should take another look. We hope you join us! This also positively affects Sons of The American Legion and American Legion membership eligibility.

Going to be replacing both on the same truck thanks man much appreciated!!

Whew! I went to the hardware store and got a new one...I had the old one to match it up,since they had that Danco, I told the cashier to throw the old one away!! Boy did I screw up!! After putting the new one in(it was too thick). I watched this video and immediately drove back up and dug through her garbage can til I found my old one. Came back home and swapped that C shaped piece and reinstalled it...walla! Thanks so much for this help. Most guys were saying to sand it down a bit...

Mine is too stiff, and I threw the old one away at the store...smh

thanks, i got a 5-cent seat and shaved a plumber call

This helped me a lot to change my water faucet. Thank you so much for sharing your video, it was a great help.

Hello! My set up is missing a step I think.. I have springs and cups to go with the valve??? Please help :)

Did you turn off the water first?

Have a 2004 and no port there

Very helpful! Been looking everywhere for a video that matched my faucet set!

New top pad need to face bottom and holes face up when installing I had same problem and I sanded new pad and put some vaseline so it works but I needed to play with it for some time. Slots on “medium” part(part with rubber o ring) need to be aligned in small pipe slots so diverter can turn in pipe itself in order to split water between faucet and shower head. This might be of some help. Good luck.

Set 5 for the rear bearing. What kind of bearing Is the smaller one?

That was extremely helpful. I was trying to change the same fixture. I could not figure out the last step you used a needlenose to pull out. Thinking like many parts it needed to screw out some way. Thanks.

Thank you sir

That shouldn't slide in that easy without lubricant, and the rubber pad should be on top and bottom, so one of them may still in the piping. Maybe i have a lot to learn

Ok so my 600 series. alve is to deep into the wall so the cartrige dome is litteraly flash with the wall. The o ly thi g sticking out is the stem webre the shower knob/handle goes. Will tbis help me extended out more?? My cartrige is the one with the ball

Thanks for the video inwas looking for that

That trick fixed my problem, thanks a million!

I just replace mine thanks for the help 🙏

Finally someone made a video that helped me!

So, can I just plugg that diverter opening and the tub pipe to only use shower , without replacing the main valve?

Omg. Mine, Ace (store brand) -came from Pax hardware, is doing the same thing.The new piece does look thicker and it was hard to push it in. Last time I did it many years ago I didn't have any problems like I am now. First time I put the new on in it wasn't all the way back. I thought it was bc it was tight. I turned it on and the water went down in the wall to the ceiling.

Appreciate your video but if I were you, I would change the plug-in connector that connects to the headlight .That seems to be your problem. It is overheating, and the connectors are loose. Just a thought.

Tighten first Then back out

I have a 98’ and the problem I have is when it’s a very cold morning and dark, my lights won’t come on till the truck warms up. Could this be my problem?

Should I turn off the water? I don't think so because this is basically a switch. Thanks man!

Is the switch supposed to click and turn the headlights on after putting it together I changed it now my dome lights nor headlights come on

I would of like to see what happens when you turn on the water and if the diverter worked probably

Well, did it work when you turned the water valve on? I would have liked to see that it worked. I just took out my diverter valve and didn't see anything wrong with it. But it still will not divert water up the riser pipe to the shower head. I'm dumbfounded.

I can’t get mine to swap from shower to faucet.

Thank you very much

By using the old top pad did the trick, the new one was too tight. Thanks for the tip!!

I like that you didn't talk for 8 minutes at the start. Thanks

Thank u

you said it was still dripping?

Appreciate it thanks been lookn all day thanks

Thanks thanks thanks!!!!!

Definitely not the same as the '97 Sport with the V6.

I have similar set up, very old. Water dripping a lot unless I tightened up the hot water knob very very tight. Is there a video to show how to fix the hot water knob please???

Does anyone know what replacement knobs to use for this type of system, hot and cold knobs, thanks...

Thank you for this I thought I'd have to replace the whole 3 part faucet system. I needed research 1st and you saved me money thank you again. Part # was correct as well 👏

I found that thread tape on the threads the metal cylinder threads onto helped prevent any small leaks that may occur behind the wall.

thank you very much sir, I was extremely confused on how to get the actual switch part out even the autozone employee couldn't figure it out we tried pushin on everythin that looked like a button to no avail little did we know we were pressin the wrong buttons 😂. this video was very much helpful lmao.

🤔🤔I have a 2002 dakota. Am curious if its same. My panel is different but same side.

Thank you for the video. Helped me a lot