6 ай бұрын
6 ай бұрын
10 ай бұрын
Пікірлер
@QQQQQman Ай бұрын
Hello! Nice job!!! What size are the half round routed cut outs please? Also the hole in the middle, do you use any special adaptor or connector to fit the tube from the vacuum unit cable? Thanks
@allaboutmarquetry Ай бұрын
Hey there, The half round router cutter 'Cut' outs have got to be as deep as the rubber. So I went in about 3-4mm. Width was around 10-12mm, The point is, is that the rubber can easy slide in and fill the curved edge and create a seal.. I used a brass ring with an extrusion on it, which fitted nicely into the pipe. If you got piping, then work with that first, The pipes take away the air, so there very important. So just make sure you seal everything or it can leak out. I placed a rubber O ring under my metal ring plate thing. And make sure you seal both sides of the MDF plate, or your vac will start to suck the air out of the MDF - and it will slow down the process and make leakages easier and on top of that - you will lose vac pressure sooner. Hope this helps - keep asking Q's - if you need more advice Im here for you..!! Kindest - MM <3
@QQQQQman 29 күн бұрын
@@allaboutmarquetry Dear "MM" - thank you v much for responding and your insightful comments which are really much appreciated. I think your generosity of spirit in sharing your knowledge is much to be admired! I`m really minded to give this a go but my dimensions are limited to 1m x 0.7m which although much smaller than your table is large enough for my needs (marquetry). So, 2mm para-rubber means a 2mm "hole" or depression in the half-round or even 3mm - 4mm perhaps. So brass ring and the pipe slots into that and the ring into the MDF by the sounds of it. I have a vacuum pump lined up which is probably overkill for the size of this. The most expensive bit is the rubber. So as costing of (in GBP): MDF about 30. Rubber: 75. Pump. 60. I don`t have a half round router so have to pay someone to do that = 50. Workbench to put it on: 20. Total: 235. Compare that with trying to source a marquetry press which is not available except by special order or using some improvised book-binding press. Your needs are no doubt much greater than mine as I am just a hobbyist but am looking to commercialise my work. Sell it in others words. So perhaps 235 or 250 is not a bad bargain. I am sorely tempted! PS - the URL link to your website did not work for me. Is it still live? Thanks again!
@Idea2Item-uo5ix 2 ай бұрын
I'm so curious how the table is going to look in the end! great project!😊
@fatigedz 4 ай бұрын
Hi, is there a second part?
@allaboutmarquetry 4 ай бұрын
I have about 8 or 9 videos - I just need to edit them and post them. This one was connected to a window method lesson I created - that's why I posted it, for the students. I can do more if you would like. Grts -Mm-
@mikhailfaktorovich1712 2 ай бұрын
@@allaboutmarquetry Second part, when you cut a black part without holes between pieces is much more interesting.
@allaboutmarquetry 5 ай бұрын
Don't forget to watch it through, the inverted sawing is near the end of the video..!
@VinceEspositoJr 5 ай бұрын
Very interesting process. First time I've seen something like this.
@allaboutmarquetry 5 ай бұрын
It works..! Ask John..! :)
@VinceEspositoJr 5 ай бұрын
The suspense is killing me!
@seanrobinson203 6 ай бұрын
you should try some finger boarding that climbers do to build callous on finger tips that way it will help with finger sorenes.
@whitlockwoodendesigns1858 6 ай бұрын
Thanks, so obvious when you think about it, but I wasn't, lol. Keep up the good work 👏
@allaboutmarquetry 6 ай бұрын
Im always happy to have helped ! <3
@magnoliaweathershield443 6 ай бұрын
i appreciate your advice. Thanks.
@VinceEspositoJr 6 ай бұрын
It's good to see you. I hope you are doing well. I'm looking forward to this video series.
@fredpierce6097 8 ай бұрын
Whoops. I just found your video on sharpening scalpel blades! 😂
@allaboutmarquetry 8 ай бұрын
Enjoy, - let me know if you need any more help or tips. Grts Mm
@fredpierce6097 8 ай бұрын
You may discuss this in some other video but I see that you use a surgeons type scalpel with replaceable blades. Are those blades you employ single or double bevel? Etc….
@allaboutmarquetry 8 ай бұрын
Double edged.. :)
@shaurus68 8 ай бұрын
A good interesting video. Taking the time to systematically work through your process ahead of actually cutting wood takes dis ipline but in the end saves on waste and results in a much higher quality piece
@allaboutmarquetry 8 ай бұрын
Yes, indeed. Its about looking ahead and prioritizing were its more essential. Thank you for your support ! <3
@VinceEspositoJr 9 ай бұрын
Marcus, is bookmatching beyond the scope of our group? There are plenty of good vids around on a basic bookmatch, but I have not been able to find anything reliable on a simple 4-way match and I'm struggling to figure it out on my own. Might this be worth a demonstration video? If it's outside of the group's subject matter I fully understand. Thank you.
@allaboutmarquetry 8 ай бұрын
I will definitely look into this. Book matching is part of the advanced veneering skill set. Its generally used for furniture, but I have seen a few clever marquetry people use it as a subtle decorative back drop to their artwork... I will see if I can find some veneer books I have, if not I will order a few packs. Thank you for your input. I will get back to you and the channel ok. :) <3 Grts M <3
@VinceEspositoJr 8 ай бұрын
@@allaboutmarquetry Thank you. Marcus. I tht I would practice making some wall art pieces first before trying furniture. Love the channel.
@allaboutmarquetry 9 ай бұрын
Reach out on Reddit, Instagram or FB. Links given. Headset: www.hbm-machines.com/nl Italian Coloured Veneers: legnoquattro.it/en/ Enjoy !
@VinceEspositoJr 9 ай бұрын
Hello. I just discovered your channel. Thank you for your generosity with you time for making the videos. You refer to "lesson notes." Can you tell me where I can find those? Thank you.
@allaboutmarquetry 9 ай бұрын
The lesson notes are for those who have joined the marquetry course I am doing. However there are a few basic one that are available online. Our Facebook channel (All about Marquetry), has some files you can down load. Failing that find me on Reddit (Marquetry Advice) , Instagram (All about Marquetry) and send me a DM with your email and I can send some over. Thanks =Mm-
@user-yg5jl4zp5s 9 ай бұрын
Marcus, thanks for posting your Marquetry videos. I have a question. Are you shadow casting veneer that has been glued to a substrate already? if yes , wouldn't the heat from the sand weaken the glue bond.
@allaboutmarquetry 9 ай бұрын
Thanks for your post and message, So far I have not seen any evidence of this happening. I have used basic wood glue, you could also use resin glues instead. But I would practice first and experiment :) Grts M
@johnobrien4014 9 ай бұрын
Excellent process. Thanks for sharing. This is something I have not seen before. May I ask where you learned about this?
@allaboutmarquetry 9 ай бұрын
I am a time served CabinetMaker from UK. I did my apprenticeship from 16 ( 34yrs ago now) and was trained by traditional master craftsmen. I have a lot of old and forgotten skills & passed down knowledge. Yet some, over the years has been self taught too - with dedication to the art <3 Thanks JB :)
@allaboutmarquetry 9 ай бұрын
I decided to upload this video, because I didn't see the point of you waiting around, especially as 1 & 2 are very similar. Just glad to help John TBH. <3
@johnobrien4014 9 ай бұрын
Well I appreciate learning something new that I have not seen here in the States. Keep up the good work.
@allaboutmarquetry 9 ай бұрын
@@johnobrien4014 Yes is it a different way of doing it. :) Im on FB, Instagram and Reddit too. Feel free to touchdown. Need help, let me know kk :)
@johnobrien4014 10 ай бұрын
Where can I find part 2?
@allaboutmarquetry 9 ай бұрын
I just posted Part 3 too, Why wait..?! - Enjoy and good luck with your projects..! :)
@allaboutmarquetry 9 ай бұрын
I just emailed you and messaged you in IG. :)
@johnobrien4014 9 ай бұрын
@@allaboutmarquetry got it, thanks
@johnobrien4014 10 ай бұрын
You should learn how to edit your videos so you can CUT out all your prep BS
@andulinointarzia 10 ай бұрын
It was a great and detailed video. I think you are a really good teacher and I’m glad I know you 😊 Ps.: your tweezers is awesome. Where did you get it?
@allaboutmarquetry 10 ай бұрын
There surgical, I think I bought them at some sort of army surplus store years ago..! Thank you <3
@ucenicul 10 ай бұрын
Great video Marcus
@allaboutmarquetry 10 ай бұрын
Hey there, more on the way ;) Thx <3
@user-xl8eo3zm1l Жыл бұрын
Another interesting video which makes you think about another part of the picture. Looking forward to the next part especially what you have decided what you are going for ship wise.
@allaboutmarquetry Жыл бұрын
Thank you - I'm burning the candle at both ends :) and working on new content. Its up when its up - hopefully sooner than later Thx
@user-xl8eo3zm1l Жыл бұрын
Loving the series so far. When will part 6 be available to watch. 😀
@allaboutmarquetry Жыл бұрын
Sorry Andy and everyone, been taking on too much and with school holidays - its hard to find the time. :) <3 But No 6 is here for you..!! <3
@rayscrafield2106 Жыл бұрын
Thank you for showing this trick. Now all I have to do is buy one and some blades.
@allaboutmarquetry Жыл бұрын
Cool Ray..! Glad it helped - let me know if there are any other things you need some tips on.. :)
@angelpaul8678 Жыл бұрын
😄 P r o m o s m
@BasRobin Жыл бұрын
Curious to see if it holds up to sanding, Which dyes did you use for this?
@allaboutmarquetry Жыл бұрын
I have been very busy doing tests, and working on doing samples as we speak... I will be using a combination of selected and self made coloured veneers. Ty :)
@skwalka6372 Жыл бұрын
I am curious to know why you wrote "Basic's" and not "Basics". Has the English language suddenly mutated in the last few weeks?
@allaboutmarquetry Жыл бұрын
Because of a mutation in the language used by AI
@irishRocker1 Жыл бұрын
think you meant it was 43 years old right? Great work, swans are beautiful
@allaboutmarquetry Жыл бұрын
Iol - Im going on 50 and want to spend the rest of my time investing in helping people learn it. YT is a great way. Thank you for your post. Kindest MM
@311278joel Жыл бұрын
💯👍💯👍💯
@311278joel Жыл бұрын
Superbe vidéo. Merci Marcus 🙏✨❤️. Tu as tout mon soutien !!
@allaboutmarquetry Жыл бұрын
Merci Joel <3
@allaboutmarquetry Жыл бұрын
Love your work too joel <3
@gabrielazaioncz8609 Жыл бұрын
Your channel is so good, thank you for your content on marquetry, its hard to find good information about that. Hugs from Brazil. Mikael and Gabriela.
@allaboutmarquetry Жыл бұрын
Thank you very much indeed, I hope to continue serving the community and help people who would like to know how to do it correctly, precisely and with the patience of a master. Please touch down with me on Facebook, LinkedIn or instagram. <3
@ucenicul Жыл бұрын
If the veneer shrinks from the heat, what do you do with the shrinking parts? Do you do hot sanding first and then cut them? PS: you can only focus on the area where the pan is so that we can see the details better
@allaboutmarquetry Жыл бұрын
I put the piece of veneer I want under the window, pencil through with tech pencil and then add on 1mm +- then cut that line. Then I sand shade and if it shrinks, that extra allows for it. It's then simply to recut the veneer to now fit. If you want add a bit extra - but it's just see what works for you. Unless your doing extreme fine tune sand shade lines, most of the time you keep the shading on the area you need for the effect...
@allaboutmarquetry Жыл бұрын
We will do more marquetry workshops, I liked the live session we did - maybe next time I will do it for real. Anyone can join me - just get in touch..! So simple <3
@ucenicul Жыл бұрын
Nice work, congratulations. I do it as a hobby, but I would like to see how to glue a marquetry work on curved surfaces without a vacuum press.
@ucenicul Жыл бұрын
I don't like to use scotch tape because it is difficult to remove, I prefer masking tape, although it also leaves traces of adhesive if you put it in the press. I haven't tested the so-called "blue tape" because I can't find it to buy in my country.
@allaboutmarquetry Жыл бұрын
Touch down with me via fb or Messenger and I can set up a day, afternoon, spare time and do a live video call with you, in the least email you a larger reply. :) I have a few tips you will find very useful that are in this subject. Peace out. MM
@ucenicul Жыл бұрын
@@allaboutmarquetry Thank you
@stevenolove Жыл бұрын
Top
@stefankoenen939 Жыл бұрын
I used to work together with him on yachts interior. He was always the one who did the fine works. A good guy and a good teacher. Love to see you starting this journey buddy!