I agree 100% what you said. WonderMill should acknowledge this. I ended up buying the wondermill electric too. I use the hand crank grinder for small and medium tasks like cream of wheat. But, as you said I use the drill bit for butters and masa with the stainless steal plates. I ended up buying the Beaur 9amp 120v Corded Drill which is always on sale, and even when not it's $60. Powerful and meets the demand for turning at low RPM's but plenty of torque.

Q.) Are your peanuts Roasted? In the shell ? Salted ? *Share a Link for the peanuts !!*

You have to watch the power tools though. I've heard of ppl going to fast, I guess, and the plates heated up to much and broke. Is it true - - I don't know but read it some time ago !!

Thank you for not making this 24 minutes long 🙌

Did your camper originally have a hitch or did you add it afterwards. Can you add a hitch to camper bumper (reinforced or not) or do you have to reinforce the frame?

I’ve been looking all over for a way to fix this without having to buy a new one thank you so much for your tutorial

Thank you

Do you need any replacement gaskets? Can i just got out to my garage and do this today without having to order anything?

you can make grinding hard grain like corn a lot easier by first running the grain through a blender. you can do the same with wheat. it make hand grinding easier. been thinking about getting this drill adapter but don't want to have to buy a dewalt drill. too expensive. harbor freight was my choice . so maybe the answer is buy a cheaper drill then run your grain through a blender first. that may take care of the problem, it does make it easier when using the hand crank. have not tried the drill adapter so i'm just guessing.

Just stumbled across your channel looking for DR650 and Happy Trails content, and now see you actually own the company now lol Enjoying all the videos from the past, hope you're able to come back and make some more 😃

Duh

Duh

Ooooo stop making that Styrofoam noise!!!! 😆 😡

Looks great.

Im not sure what your problem has been with it. I personally have had a great experience with it and no issues using it for either the stone grinder, or the steel burs. I use a Dewalt 10 amp 3/4 inch drive corded drill and have used it daily with no issues. All I did was follow what my local dealer told me as well as what I was told on the Wondermill website.

You're lame

Thank you so much for this. I ordered one of this from My Patriot Supply for my son's dorm room. There were no instructions. We have a huge reverse osmosis system and a charcoal filtration system in the house. I wasn't going to risk his drinking water. I just might buy one of these for a back up. As far as I can tell, there is still only one independent study of this filtration system.

I have one f these and you are mistaken if you think the OEM tripod is anything but trash. The one you obtained with your spotter is much better than the factory one. The factory OEM is so bad that just sitting on a table the legs will bend under it's own weight. Agreed on the buy a real tripod for cameras is the best thing and will not need a table to use. The issue with the tabletop tripod has a problem with shaking to veiw anything

...some of them will come with... 18:59

That was easy

I made the trip through Silver City to Jordan Valley on a 1975 Electra Glide, in July 1984. Had a great burger and beer in Silver City. People there couldn't believe I rode that bike up there.

Thanks for the idea for the fuel transfer from berrals to berral

I ended up in emergency with cracked ribs. I worked with harder than I shouldiv been I'm 70 it's been in the box every sense

I’m thinking of installing one of these in my camper conversion. How about if I created a sealed box inside the van and put the heater inside. It would be vented to the outside with some holes in the side panel and floor. Maybe an electric extractor when the boiler is on. The box would be lined with fire board. Could that work and deal with fumes issues?

Nice, thank you. Noticed a tapping sound in the top end of my wife’s KLR the other day… of course she has no clue how long it’s been going on. Hoping it’ll be a simple valve job if anything.

Why wouldn’t you just do the 705 kit or whatever it is?

I want to buy that kind of drum I bought two

For 30.00 or 35.00, it is not worth my time to try to fashion some part to make a work around. That to me does not seem unreasonably expensive. I used my mill this past week for the fist time and milled to half gallon jars; 1 of hard winter wheat for bread, 1 or soft wheat for pastry flour. Having done that and having issues with both shoulder, I wouldn’t want to do it again. Therefore I plan to buy the pulley set and control swith for $100. I will get a used motor as that is the most expensive part. I thought about using the drill attachment however, running the plates too fast will damage them and in my opinion the plates are too expensive to replace (about 90.00) to save a little time. However if I could not afford the pulleys and switch, and had the proper drill, the speed of which could be controlled, that would be another story. And BTW I was surprised that anyone would consider connecting a hammer drill to the grain mill. I think this is not a good idea. It likely would exert undue forces not only to the auger and stones, but to the casing. It would eventually manifest somewhere in the mill; likely the casing which is cast aluminum. And probably it would damage the stones as well.

Are you no longer affiliated with happy trails your code doesn’t work anymore

Your discount code isn’t working for happy trails

Awesome video!! Short and simple and easy!

Do you not need a graphic bushing in the connection from the mid pipe to the header ?

They will be a great use for industrial vacuum.

Looks great

What is this box

Hi man, just watched an old vlog from you about the windscreen extension deflector from 5 years ago. My question is, do you still have one on your bike and was it worth buying one.? Cheers.

Interesting! I wonder how it compares with an old Gopro Hero8 as it comes to video quality. Your outdoor shots with the camera looked pretty good to my old eyes.

Thanks for sharing this informative video. I bet that peanut butter tasted good!

Very nice of the Owner 👍 He should have charged something for it. I will get these for my KLR Thanks for the video 🍻

Will a helmet fit in this case???

Totally useless video when you don't mention what values are in spec

Praise the LORD for creating trees!

Praise the LORD for creating useful mills!

Isn't it necessary to change the auger? I believe it is.

Nice 👍🏻

I have a 2023 klr 650 adventure . Will this skid plate work with factory lowers?

This is a few yrs old, how is the drill and mill working out.

Also try to make your plate seams land on a stud or add them in accordingly

Your window header isn't right either should be at least 2 2x4 with a 1/2" piece of plywood sandwiched between them and placed 3 1/2" face vertical

You check your valves and you check them often!!!