I don't have preferences under file on Mac?

Can we do it using bluetooth ? i m use to arduino ide

If I close the browser and look at the data tomorrow, will it show yesterday's data?

can i use ESP in AP mode in this case and connect clients to access internet? including NTP servers which works over UDP ?

I am having issues that the status and buttons are not matching the ESP. Using more than one browser at the same time creates a big confusion.

Top notch explanation.. thanks

Does this work on esp8266?

Assalomu alaykum RuiI am from Uzbekistan. what I have done is commendable. May Allah make your deeds better than this. but it gave me an error A fatal error occurred: Serial data stream stopped: Possible serial noise or corruption. Failed uploading: uploading error: exit status 2

Great Tutorial! I really appreciate! What about latency? I want a colse to realtime solution. (200ms)

Invalid HTTP request

In the loop, the sample code performa a write to the servo object. Does the servo or does the esp32 know the current position of the shaft? For example, if the shaft is at 45 and I write 45, the shaft should not move, right? Or, should the shaft perform a sweep to calibrate itself? 8 guess that's ultimately what I am asking is do I need to calibrate the servo before writing degree values to the servo?

Thanks so much, concise and clear

soft RemoteXY in smartfone 👍👍

If I haven't watched it till the end I would have never known it's real time application.....thankyou ji

hey man, there's an error like this while i upload the code: exec:"cmd" : executable file nt found in %PATH% Error compiling for board DOIT ESP32 DEVKIT V1 what should i do?

can this be done for raspberry pi 4

very use ful for me. Thank you.

Good video

Wow can you do it DHT11 sensor

I miss the ADC calibration part.

Why a simple Bluetooth class 80% program memory full

pls be vegan animals also have lifes Radhe Radhe

Hi 😊. it works the other way around, when turned ON on website it means its turned off on my esp where can i change it ?

i'd like a link code?

awesome..

Is it possible to use and esp 01(8266) to send data to an esp32 using ESP now?

Thanks. Helped a lot man.

it says "this site can't be reached" when i tried to put the IP address

The PIR shown is used by many projects. I got a bunch of these to use for my ESPHome projects around the house, and all of them fail miserably, with false positives. Every few seconds with some of the sensors, to every few minutes for the better ones. If you search for this sensor, people complain about how useless they are, and the frustrations and waste of money. No amount of pull-up or pull-down resistors, added capacitors are going to fix it. I found a place they suggested to use the Panasonic EKMB or EKMC series PIR's. You can buy these from DigiKey or Mouser. They are a little more. I got some of them, and they work perfectly. The one I got said the data pin would be VIN minus half a volt. So for my ESP32, I powered it with 3.3 volts so I wouldn't overpower the data line to my ESP32. I would not buy the sensor listed for this project, substitute it with one of the Panasonic ones.

Wonderin when using a reed swtich how could you make it do when the reed switch goes from open to closed it also triggers the esp32 to turn on as would be great to have it trigger when the reed swtich changes state...any ideas ?

I need to do this at some point. My solar setup (tiny 12 volt batteries) must be off at night (draining from the controller, mostly) and my sister got some ideas where she lives.

Hello Rui. I tried to follow it step by step. I have a doubt. I can't find ESP32 sketch data upload options

I selected NodeMCU 1.0, ttyACM0, tried to upload blink, I get error, Failed to connect to ESP8266: Timed out waiting for packet header_

iotide.blogspot.com/2024/06/iotprojects-temperature-and-humidity.html

Nice ideas thanks

Aàa😊

Se puede actualizar la grafica cada 10 milisegundos?

A fatal error occurred: Failed to write to target RAM (result was 01070000: Operation timed out) please help

Does it take any charges to host on internet webpage?

thanks u

How can we send the time duration the light is on when sensed by pir on some cloud or Google sheet?

شكرا جزيلا !

Very good review.👍

Great video, but I have a question...can ESP32 communicate with 2 methods at once? for example like ESP 1 - ESP 2 with ESP-NOW, then ESP 2 - PLC with wifi communication...

Nice project 👍👍 it's working well

Thank you for this video tutorial! I think building a PCB is way over my head for now but I would love to use these in my projects. Is there a link to this board or a comparable board that I could buy, ready-to-use?

what if i only need a push botton that means the LED will only lit when i hit the push bottom...do i still need the database ?

Hello, Under Tools tab your programmer is set to "AVR ISP mkll" but I'm only getting the option "esptool". How can I solve this issue? Any help would be appreciated. And I'm getting an error "A fatal error occurred: Failed to connect to ESP32: No serial data received."

Always enjoy your tutorials!

Thank you so much!! 😊😊