I'm a retired P&G plant technician and I've only seen purple, green, blue and red loctite. Is orange something new?

Having that over sized tire on there caused all of the problems you encountered Tony. There was at least a 1-2 inch difference?? Thats why that hole was wallered out and those bolts were stripped, That was just way too much of a misalignment. Great job on fixing it👍

Hello, Tony, the clutch shaft has axial play, not up and down, but the clutch can be moved towards itself, what could be damaged?

Great job Tony.

Tony where did u purchase this seat cover? I am now trying to decide if I want to try this or go get it done. Thanks

Definitely don't need to take all that off just for the carb

Tony, I can’t get the rear wheel back on. What can I do??? The splines seem to not match up now?

Thanks very much Tony, very informative. I have sold my Helix and now have the Reflex.

Hi Tony, I am having an issue with popping on deceleration and I have to set the idle up higher than normal or it will stall. Idles up and down on its own. Other than this it runs great, great acceleration with no hick ups at all, tops out at 71 mph. I The carb is a china one, the jet I noticed is a 108 not sure on the low speed jet right off hand. My brother has a helix with a stock carb and his runs perfect, I took his off and put it on mine and it ran like a new scooter so I definitely know the china carb is the issue, what size jets would you recommend that I put in the china carb to possibly solve my issues? Also do you know how many turn out I should be on the air/ fuel mixture screw?

Tony, these videos are super helpful, thanks!

How many miles did you put on those break pads ?…they looked still pretty good. Thanks for the vid 👍🏻

MORE HONDA HELIX VIDEOS! (please) 🙂

What battery do you have in it? Ive done tons of research and found nothing on an upgraded battery.

Brasil 🚛🚜👍

Thank you for this 🫡

Hi to my cn I only put 150ml as reported in the manual, and watching this video I saw the oil dripping. My 150ml didn't drip so you put more or I put little thanks

Can you tell me the tire measurements, greetings and thank you

I’m sorry if I missed it but once you upgrade the jets and get the pod filter on is there anything you have to do to the original airbox? The snorkel will be off

If you replace pod filter with out replacing jets, will that be okay ? Or is that step required for this to be successful?

Hello, could you tell me the model of the tires and where to buy them, greetings

pause in the beginning of your fucking* video that you don't know what you're doing your battery is not charged and you don't have a clue about what the process is

Thanks for the video!!!

Thanks, Tony! Works great on my Helix!

Thank you for your great how to video's ! They are great help to us amateur's ! They do help me do things on my scooter ! Thank you !

Tony you are the man!!

Hi u need to remove the sleeve and there will be 3 pins u can remove and it all comes apart. It will need to be lubed to perform its best.

Hi Tony , Sorry to bug you again , but I've encounter another problem with my scooter . The starter motor rotate freely , but doesn't engage the flywheel , hence the engine doesn't move . Do you think the problem is the starter motor , or worse , something got loose or broke behind the side cover , where the engine oil goes ? I've removed the starter and turned on fine , but I'm not sure if the shaft of the starter must move out when giving a crank , like a car bendix , and then retract back ( mine doesn't move ,just spin ) . Any help would be greatly appreciated . Thanks.

will a cheap secondary clutch work just as good or am i better off rebuilding ,, just trying to do it the easier way without breaking the bank lol

cool!

Peace

thanks for another helpful video ..

Brasil 🚜👍

thanks for all the Helix content Tony!

I used a zip tie to hold the lever down, open and close the bleeder, remove the zip tie, and release the lever to bleed on my own. Had to do that a few times and worked pretty well.

Dude where do you get the master cylinder I need one ! Information please !

I have an 86 that idles smooth as silk but on runup, it has a terrible bikewide vibration that rattles the bike ad high rpm. Any thoughts? I have a new variator and clutch and belt. My "guess" would be worn motor mounts. It only has about 8K miles though. Appreciate any thoughts.

I just changed out my belt yesterday, and I learned thankfully without the belt cover on to make sure the belt has some slack when installing the variator cover. The first couple tries I had the belt too close to the center of the variator which made the nut spin off when running.

Hi Tony . Do you know how to remove the speedo gear on the front wheel of a Honda 250 that's located behind the brakes pads ?? It looks like the only way to get it out is from where the speedo cable is attached to it , but I'm not sure if there 's something holding that gear . I don't want to put much force because I'm afraid to brake something ,then not being able to fix it or replace it . Any help or tip would be highly appreciated . Thanks.

Hi Tony...not sure if you will see this a year on but I have a question. My Helix has not been able to get above 45 mph. The carb is a new replacement. It really seemed like a fuel or air issue so I checked for air leaks with starter fluid, tightened up air box, ran Sea Foam through it, changed to a new plug and even put in new rollers in case that was the reason (it wasn't!). Yesterday , just in case there was water lurking somewhere, I drained the entire fuel tank, replaced both fuel filters with generic filters from AutoZone and installed a new fuel pump. I did NOTHING to the carburator. When I started it back up after doing this, it started fine and ran for about 30 seconds and then gas began to stream out of the vent tube you referenced at 6:20 of this vid. After that it would not restart and every time I tried, fuel would spurt out of that vent tube. After sitting all night I restarted it this morning and it started fine, ran for 45 sec and then fuel once again began to pour out of the vent tube. This has never happened before. Is it possible that the new fuel pump or new fuel filters could cause that?? Thanks so much for any ideas!

Do have a Honda Helix carburetor cleaning video? Thanks

Hi please i have a helix also wanted to know if can just go ahead and put a pod filter on the carburetor or i need a special kind of carburetor

Hi Tony, how did it run after this? My clutches are about as thick as a dime right now.

Where did you get the radio? Do you have a link? Very interested in getting the back LED light bar too. Great work!

Why is there 2 cables going to the throttle? Mine only has one on a dune buggy with this same carb. Mine does have the provisions for the upper cable though. Sorry for the dumb question

This post is not for Tony but for all others. The Kmod did not work for me on my Reflex. The rpm was way too high on the highway and my fuel mileage was very poor. What did work very well was installing the face "B" of the variator from a 2005-6 250cc Big Ruckus that has equal length runners. At first I also, with the variator change, I installed the 26 gram rollers that are stock in the Big Ruckus which did give me great fuel mileage and great top speed but the acceleration was poor below 45 mph. Went to 24 gram Dr Pulley sliders and WALLA, that woke up the get up and go on this scooter and that was 4 years ago and I have never looked back. Because of the amount of miles I put on every year(roughly 10000 miles a year) I change the drive belt every spring and inspect the sliders for wear. There is a little over 30000 miles on those sliders and they still show NO wear or flat spots on the back sides and it still shifts perfectly through all the ratios. Later folks, gotta go for a scooter ride!!😁

I just bought two '86 Helix today, and they both need rear tires - the one in the video looks like the Kenda based on the tread - how do you like them? How are they in the rain? Thanks in advance, greetings from Montreal, and keep the rubber side down!

Why does it need to be re jetted? Couldn't you just adjust the mixture?

How much can a helix bring in now a days in Oklahoma ?

Greetings Tony I have a quick question . Any advice on removing the head cover gasket ???

I Dremeled the tab off the bowl and can reach under with my fingers to adjust the idle mixture peeking the idle and no tool.