My nova was doing this on Webers. Was down to the ignition system.
@Roundstone29 күн бұрын
Many thanks what did you change?
@RANDEEP685Ай бұрын
Shit video
@jrh862 ай бұрын
Thanks
@sunnydhanda17232 ай бұрын
Thanks
@billywhizz982 ай бұрын
I always prefer to use a rug doctor as it always cleans up well
@jenabby072 ай бұрын
Having done this many years ago it will require a reasonable amount of cutting. Tunnel needs to come up a few inches and modified sump. If they have hydraulic clutch at the top of the bell housing same as the earlier boxes it will also need a relief in the fire wall. If it was me I would leave it as is due to the value of them these days. Better off putting it in something cheaper
@Roundstone2 ай бұрын
My tunnel is an auto tunnel so big enough loads of room around the type 9 gearbox.
@markbritton64853 ай бұрын
How long would that take to dry out? Been looking at the blissel one & a vax one for around £100 & look very similar to the rug doctor. Cheers
@Roundstone3 ай бұрын
Hi not long I brought my rug Doctor from there website as a recon machine. For £80 very good machine, and it don't take that long as it socks out most of the water. Just put car heaters on and it fine.
@axnn12 ай бұрын
@@Roundstonedo you have a link? Cheers
@markbritton64852 ай бұрын
Thanks 👍🏻
@gaugesheen3 ай бұрын
..............Choob
@denisdelaney47893 ай бұрын
No no no 😢
@DjWhaYoFace3 ай бұрын
Nice got wait to see the finish of it
@billywhizz983 ай бұрын
Looking forward to seeing it and thank you for shearing your power steering column conversion
@Roundstone3 ай бұрын
No problem Billy glad it was useful.
@charliecoco21153 ай бұрын
Great result!👍 You forgot to show the money shot of the filthy water empty out.
@billywhizz983 ай бұрын
Great video I need to do mine
@phuckphossilphuels54703 ай бұрын
Bought one new in '95..Canary yellow. Sure as he'll want another
@dgmdgm72713 ай бұрын
Limited rusty !
4 ай бұрын
4 years and it's still helping people like me to do ours on our citroen relay that has the same engine in.
@mkab0075 ай бұрын
Happy to see old car restoration. My father have this model car, 10years rest in garage.
@callumhawkhead74977 ай бұрын
Hi mate, I’ve watched one of your videos on replacing a lower control arm on a transit custom. I’m struggling to find the part number for the bolt you replaced that goes through the subframe into the frame. Any info I’d greatly appreciate as I’m really struggling. (Commented on here as this is the only video I could find with comments enabled)
@Roundstone7 ай бұрын
Hi if you contact ford the parts department they can email a map with part number and pictures
@northeastmx26007 ай бұрын
Great video 👍🏻 has helped my do mine without sending it to a garage again as last time I got charged nearly £100 labour and £12 for part
@paulmcmahon78 ай бұрын
Nice work with the rear seat, will have to do something similar, but not for a while yet. What is the exact orange colour of your car?
@debeerpaul9 ай бұрын
Lol the music 🤪
@oscardesignstudios10 ай бұрын
How is the baking soda- loctite combo going after 4 years?
@eddynoneck11 ай бұрын
I replaced my battery but it works for 5 mins then dead again. Do you think its a dud fob battery i purchased.
@Roundstone11 ай бұрын
Possible I had a dud one once some cheap one from ebay.
@brynmarshall8716 Жыл бұрын
Just brought a rechargeable battery. wish me luck with my soldering skills of Edward scissor hands
@Andysfishon Жыл бұрын
He will love that brother.👍👍
@timryabets Жыл бұрын
That guy is so lucky! I wish I had something like that
@derekoliveira422 Жыл бұрын
Battery model/ nr?
@stuartshields8823 Жыл бұрын
My vehicle is abipper 1300 diesel profesional, I’ve try ur tip with the screws but the wear is that bad to the nylon socket it still remains floppy, help please, stuart
@TheHam85 Жыл бұрын
Hi, how do the rear seats fit…….mine came with seats just sitting in position, no bolts etc. cheers
@Roundstone Жыл бұрын
What I remember the back part has 2 pins that slot it in place by parcel shelf and at the bottom 2 bolts and a small clamp. The main seat just slots in and is just pushed in place where seat cross member is. Hope that helps
@jaca2107 Жыл бұрын
hi i changed the seal on my transit mk7-2010 but i didn't put the injectors back to where they were i wonder if i should program them now?🤥
@martinfousek508 Жыл бұрын
Guys I have a same, but different problem. I have problem not in shift rod, but in coulisse..... can someone help me?
@jimmycronin5407 Жыл бұрын
Life saver! Found some with the correct engine. Thanks 👍
@sinicholls1751 Жыл бұрын
About to do this myself but ordered a seat cutting kit. These Transits need a 17mm x 17mm Cutter. You are running the risk of the new washers not seating properly if you don't remove all the carbon deposits. Also the clamp bolts need replacing as they are single use.
@freakrecords1970 Жыл бұрын
are these a decent make
@dventure.. Жыл бұрын
You sir I tip my hat 🙏🏻🇬🇧
@kesinnovativ Жыл бұрын
why didn't you put the copper rings directly on the injectors? That would be a lot easier.
@gwm_john Жыл бұрын
Where to buy the replacement fob
@Roundstone Жыл бұрын
Ebay about £3
@nexpro6985 Жыл бұрын
nice You can find the rechargable cells. I bought one for a logitech keyboard that had a "lifetime" battery in it. I'll try to get some for my transit keys.
@tobealionyoumusttrainwithl1645 Жыл бұрын
Any chance of showing us thick people how to do this in another detailed video and is it worth doing and why ..
@chrislooney8682 Жыл бұрын
How did you open the original.blue key
@charleserickson7503 Жыл бұрын
In Egypt they will restore it.
@charleserickson7503 Жыл бұрын
That is a bad show to see that station wagon in a scrapyard.I hope some one can use the spare parts.
@Bewefau Жыл бұрын
I hope you ran your speaker wire's and your audio gear on the metal before you put your carpet in.