got one from the first batch, waste of money, wouldnt wake up, thought it was a setting, nope, thought it was the microphone, spent hours with tech support who had me strip it all down to make sure mic was plugged in, it was. eventually after 2 days we found the issue, shipped with broken firmware that didnt have a working wake word, flashed back to beta firmware and it worked but the wake word was 'alexa' .... back in the box where its been about 2 years. bought a dfrobot speech board and added an arduino. I would recommend it, the HW is pretty good, but as an early bird buyer I was just 'too early'

doesnt work?

But it still downloads the source files! I need the program!

Pff. Elektor: You should be ashamed. Pointing to the negative and naming it positive.

Have you any information on how to use the micro:bit instead for this?

Thank you!

Wants me to get started with the AI projects!

👋 hi friends

coming full circle aren't we

You don't need to re-solder the connections, the motor goes in both directions, just restart it in the other direction!

not a very helpful video,you didn't explain where to get the code for the animation,im pretty new to arduino so i have no clue how to do it

Nice!

HI is it possible to set voltage for osc.generator, how to do it thanks Jan

And then.....? How to install the zip..? This is so insulting... "Click the green button... Bye!"

Thank you for a very good and technically convincing explanation of the connections between the knife and an Arduino and the special features. That was a great help to me!

Finally I can make a nice cup of tea with a raspberry pi. Until now I only baked eggs on them. 🙂

Good

Hey do you know where to find the drivers ? the usb drive with all drivers didnt work at all

Isn't this just a rebranded Owon HDS2102?

What is the capacitor name used in lt spice?

Thank you very much.

You have no answer of my question ❓

National Instruments says a high speed ADC can be more accurate than a high resolution one. You take 4 or more samples and mediate them ! High resolution ADC measures, with precision !, spikes !

Cool setup

Regarding OS on RPi Zero 2W, what OS should I use, is it still unsupported with bullseye? Can’t seem to find appropriate OS on RPi’s homepage. Can you please provide me with a link or perhaps add it to your GitHub page on the Hyperpixel? Tried using chatGPT which bricked my RPi with some changes to config.txt 😅 … Back to fresh install

can i see your code pls, thx u

If pico run the nodered does that mean the must be always connected to PC just like with RPI3 or 4 or not no need to be connected??

I only find 'getting start' for all fucker chips but never good courses.

Can we control it by connecting wirelessly? I wonder how we can do it

This seams like a payed commercial

Llama3 runs well and was able to finally get a voice assistant working. Fun times. Project's in your inbox lol.

Nice overview. Thanks!

Nice project

Really cool

Neat

But what if it doesn't have an exe?

that's good . godspeed, ;)

Thanks 😎👍

I'm adding Ollama and offline LLMs on my ai kit to program the "free" KB2040 from adafruit. I say free because it was free like the first hit of crack always is... but then you have to buy more widgets after you research wtf a KB2040 even is! Lmao

It still needs a digital signal amplifier to eliminate the so-called "ghosts"

thanks !!!

If you can type in Tera Term but can't see what you're typing, it could be an issue with the local echo settings. Here are steps to enable local echo so that you can see what you're typing: Enable Local Echo: Go to Setup -> Terminal... In the Terminal setup dialog, look for an option labeled Local echo. Check the Local echo box to enable it. Click OK to save the settings.

goated

Great fun! But why???!!

Sehr gut

Hi I built mouse jack using Arduino UNO just like yours but the payload was not working, The mousejack can detect my microsoft mouse. However It is stop at Starting Attack . Do you have any idea why?

I love book reviews

too silent :(

Great insights. thank you!

👍👍👍👍