Thanks for sharing.

Great video! Would you happen to have a video on how to change the mechanical seals?

I have a bearing that I need to replace in sacala2 how to reach to the pump compartment

Can you replace the inner case? Apparently i have a hairline crack somewhere in mine and i can't seem to find it yet it leaks out the front of the bottom. I'm not even sure how i could pressure test it to find where the crack is to repair it

Thanks for Sharing

I'm giving you a "thumbs up" because i learned something new. But, seriously, you need to hire your wife or girlfriend to be your cameraman. I almost got a case of vertigo from all of the camera movement!

Bolts not screws

exactly what I was looking for. Thank you

My pump is an older model Grundfos probably around seven years old. It seems to be leaking from the bottom. It’s losing quite a bit of water.

It's has been impossible to buy the kit. Where can I buy it?

Excellent video, I was told I would need to replace the whole pump!! You're a star

Do you have a video or guide for changing the bearings?

I have scala2 not its working even if water discharge water is off??? Working 24 hours!!! How i can repair?

Excellent video thanks for saving me money.

What the part number for the rebuild kit?

great video.. can you tell me how old is this pump? is this problem common for this plastic scala grundfoss pumps?

I love how your video skipped right trough that special screw. One second it’s on with you stating needs special screwdriver that I don’t have then blink blink your pulling it off. Blink blink equals 30-45 minutes and a scuffed up special screw. I call BullButter.

did you have to recharge the internal tank? how do you do that?

Hi

❤

Good video, i have the same jet pump. Will search the rebuild kit and make the job.

You kinda skip the part where you get the impeller off? Mine just spins not sure how you got it off? Also don't think that is a venturi pretty sure it's the jet nozzle.

Thank you. Just used this to save a couple hundred bucks. Thanks

thanks, this is very helpful. Inside of your pump looks almost new compared to mine. Lot of minerals in the water here mine looks like a lava pit.

Great video but you should added to discharge the capacitor

Thanks a lot for posting this. You saved me a bunch of money.

Great ,you helped me out of a lot

Hi .I have a 2H. mayers pump it works good the only bad is that it has a annoying noise inside..what it could be.? Any suggestions will be appreciated.

Why is the water so dirty. You sucking water from a lake or stream ❓

Is it safe to drink from that pump

Where do you buy your parts from? Having a hard time finding a place online to order parts through.

OK TYVM for excellent videos. b.t.w. this channel has 2 Myers rebuild(s), what I didint see here, I found on the other (also Helpful) video. As for the impeller, showing need to hold the shaft, OK, but I recommend wrapping cloth around the shaft end you're holding w/channel locks, etc. Myers are great pumps! I'm working on my second rebuild/clean up. I routinely do this every 8-10 years or as needed..

But here's a question what signs are there that impeller is bad other than it would come up to pressure. Are there any visible signs on the impeller because I tore it down twice and looked it over real good. It seemed fine to me no broken parts? Hmm. What gives

This was as helpful as all get out. I had to do this task and thought I'd youtube it. I punched in how to rebuild a myre pump. And presto. My concern was that was it necessary to pull off the back and those components.. And sure enough it was. Now I can rest assured I'm not going to screw it up. I'll just do exactly that. Saved me about 350 bucks.

Do you have a link for the rebuild kit? I been looking for one for my HJ75S pump...It builds pressure and works fine, but it sounds kind of weird and the pressure gauge right on top of the pump shakes around alot when its working...any recommendations? Thanks again for the video.