R P

Пікірлер

@sylwiaw8484 Күн бұрын

Dziękuję❤❤❤respect❤❤❤

@ludaalex 3 күн бұрын

Jetzt läuft der Motor nicht mehr alle Stecker sind dran. Vor dem ersten Start luftmassenmesser vergessen anzuschließen.

@fava7753 Ай бұрын

Mazda engines , one unadulterated fkn nightmare . fact .

@DelRoy-u7d Ай бұрын

How long did this take you?

@DomingoDeSantaClara 3 ай бұрын

My first cars had plugs, points and a carby...these new engines are crazy complicated in comparison.

@NTS112 3 ай бұрын

is this help with red oil light and check engine ? mazda cx5 2015 diesel

@rp8930 3 ай бұрын

@@NTS112 do you mean low oil pressure?

@NTS112 3 ай бұрын

@@rp8930 red oil warning light. Scanner didnt show code. Deisel i think in the oil

@rp8930 3 ай бұрын

@@NTS112 it is probable that the seals under the injectors were worn out. This caused the oil strainer to become blocked

@NTS112 3 ай бұрын

@@rp8930 is servicing the injectors and replacing the seals enough to fix the issue you think ? could it be the mannifold needs cleaning of carbon ?

@BioLogiK1 5 ай бұрын

how much rubbish on modern engines. 90% pipes and stuff, 10% engine.

@hastuart9639 6 ай бұрын

Why not remove the battery and drain the coolant into a bucket. Why struggle , when removing a little extra to give access saves you more time and temper than struggling.

@andrewleckie3040 7 ай бұрын

Absolutely Fantastic great work.Thank you.

@happy_forever8 Жыл бұрын

2 weeks go diagnosed with code P0401 - clean EGR intake & DPF. But after 250miles engine check light ON again (still code P0401) Any suggestions what can i do ?

@rp8930 Жыл бұрын

the egr is probably damaged. does not work within the correct range or is jammed.

@rp8930 Жыл бұрын

did you clean the intake and egr?

@happy_forever8 Жыл бұрын

@@rp8930 yeap

@happy_forever8 Жыл бұрын

@@rp8930 could be it exhaust pressure sensor failure? Or DPF sensor not working?

@nelutumoldovan6846 Жыл бұрын

Hello and I respect you to do this operation we need to remove the battery? I want to give it a clog cleaning as well after this operation you had to put the device to the test to cancel the witnesses?

@kaboomist Жыл бұрын

Thanks for the video. Think mine needs this, discovered it within 3 weeks of buying from a dealer, car went in to limp mode code P24A5 EGR valve stuck. I tried to excercise my right to reject the vehicle under consumer rights act 2015 (issue raised within 30 days) but he went dark so will have to take it to court. In the mean time, are you still doing this full carbon clean? Mine is an auto so would need to take front wheel off and remove plastic cover and turn engine over until cyl 2 or 3 is fully open then clean other cylinders, then turn over again and fully close 2/3 and clean that last.

@zhqiu1597 Жыл бұрын

It's amazing, what is the principle of doing this works?

@sabrinagaskins Жыл бұрын

No talking through it

@aleihp Жыл бұрын

Hello 🙋🏽‍♂️. Congratulations for the video, it is quite illustrative. I have an mazda 6 from 2013, it now has 200,000 kilometers on it, and I preparing myself to do this intervention. I have a question. Did you replace any gaskets or reassemble them? If you replaced any please tell me which ones. Thanks 🙏🏽

@rp8930 Жыл бұрын

This job was done as a hobby. I put all the gaskets on the old ones. I don't have any problems. Of course, if any are damaged or deformed, they must be replaced.

@aleihp Жыл бұрын

@@rp8930 Thanks for answering. I'll pay attention when dismounting, if any have damage. I also thought that new gaskets would not be necessary if none were damaged. That's why I asked to be sure and to know how you proceeded... Thanks again 👊🏽

@rp8930 Жыл бұрын

But if you wanna do with this professional, you should replacement all gaskets. Good luck 👍

@aleihp Жыл бұрын

@@rp8930 Yes, I will do my friend. I want the job to be done right 😁. Thanks for the advice 👊🏽

@tomcowdall87 Жыл бұрын

Can you just not do a carbon clean

@_molina____ Жыл бұрын

You are amazing. Thanks a lot!!

@jakubb9484 Жыл бұрын

Hi thanks for the video. Did you just clean intake holes on engine block without turning the engine and closing intake valves? What about cleaner and debris in cylinders?

@rp8930 Жыл бұрын

I blocked the holes with paper. I use a vacuum cleaner for large pieces. I pulled out a large part with a scraper plus compressed air. cleaner heavily softened the dirt. no problem with that.

@jakubb9484 Жыл бұрын

I mean, before doing all that you had to close intake valve on the ports you were cleaning, right? Otherwise the cleaner and debris would fall into cylinder? How long did it take you to complete the whole job?

@rp8930 Жыл бұрын

@@jakubb9484 you don't need to turn the engine over. you just block the valves with a paper towel. you have to make sure that there is no dust in there. Total job around 6-7 hours.

@am2am2am2am Жыл бұрын

Seen so many videos about it. All great. One thing nobody show is where you drain coolant in order to preserve it?

@rp8930 Жыл бұрын

I only drained as much coolant as you can see in the video. After finishing all the work, I completed the level and that's it. I filled up about 1 liter.

@enridgekayla5284 2 жыл бұрын

Wait,are these mazdas 2.2L diesel engines got 5cylinders?

@rp8930 2 жыл бұрын

No, it’s 4 cylinders bi turbo

@enridgekayla5284 2 жыл бұрын

@@rp8930 i just counted like 5 injectors’ fuel lines into the rail,maybe i was just wrong.Thanks

@vargaalexander 2 жыл бұрын

hy thanks for the video. i have mazda 6gh 2010 2,2. no error codes, but, the oxygen tube air is vibrating when the EGR are open. its normal? when i unplug the EGR cable, ther is no vibration.

@keileung6847 2 жыл бұрын

This carbon build up was needed on my 2.2 skyactive Mazda 6. Engine light came on at 130,000 which got done at dealership as a full clean due to carbon. Then it needed it again at 148,000 miles and again it needed it being done by dealership. Now at 180,000 the RPM goes up and down when warm at idle and blowing unburnt fuel through exhaust. So I think I need this doing again.

@gloriabaez-Barajas Жыл бұрын

How much did it cost at the dealern

@Teleport73 5 ай бұрын

Dealer probably didn't do a full clean. Next time ask them to take before and after pictures.

@KayKay-lf9nq 2 жыл бұрын

Hi mate do you know where the bank 1 senor one is on this mazda skyactiv

@kmetovitylevente4211 2 жыл бұрын

Instructive video! Thank you. I have a car like this. Cold when I start it spins up to 1800 rpm. For 15 seconds. Then back to 800 rpm. But if you have minus degrees don't do it. Only above 10 degrees Celsius. What could be the problem?

@rp8930 2 жыл бұрын

All mazda have same things. It's nothing wrong with the car. I have that same on my.

@rp8930 2 жыл бұрын

Soon I will create a list of the necessary parts that must be in this job and together with my friend who has a repair shop, I will be able to do a full Mazda service. Of course with a service guarantee. Thank you for your interest my movie.

@tiaskit 2 жыл бұрын

Were are you based?

@prestondcox1345 5 ай бұрын

Where are you in the UK

@sekla86 2 жыл бұрын

Respect for this job! You're awesome, R P :) If I'd like to clean just the throttle body with throttle body cleaner, do you know if getting access there requires disassembling the battery and getting all the air intake tubes off or is there any trick to get only there without disassembling a half of the engine? ;) I found some videos with cleaning throttle body, but all of them had a very easy access and it seems that 2.2 Skyactive-D is a different level of a challenge ;) I would very appreciate your answer, R P :)

@rp8930 2 жыл бұрын

hi, to clean the throttle you don't need to remove the battery and intake. Just cleaning the throttle won't do much for you. For a good effect, you need to perform the steps as in the movie. It takes a lot of work, but the effect is the best.

@hgvnovice2011 2 жыл бұрын

Great job mines got 83.000miles I'm gonna tackle this job myself at some point and try film it . What the time would you say takes ? And are any of the valves open when you clean the engine side ?. I might try a wet vacuum hoover for that bit so nothing drops in engine.

@rp8930 2 жыл бұрын

I used a carbon scraper and a vacuum cleaner and air compressor. Some valves were open. You have to be very careful.

@tomhelsby5546 2 жыл бұрын

Use small pipes on the hoover to catch the carbon

@rp8930 2 жыл бұрын

Exactly. I used a vacuum cleaner for carbon extract.

@tomhelsby5546 2 жыл бұрын

I thin it would be a good idea to use an old hoover when cleaning out the ports on the cylinder head to prevent carbon dropping in to the engine

@dmalovic 2 жыл бұрын

I was thinking about the same thing.

@rp8930 2 жыл бұрын

Exactly. I used a vacuum cleaner for carbon extract.

@Teleport73 5 ай бұрын

Make sure the valves are closed in each cylinder before cleaning it.

@ryangodby7016 2 жыл бұрын

Great detailed video, I am local to you and also have a CX5 Skyactive can You do this for me ? Thanks.

@MrYeah88 2 жыл бұрын

respect for removing the ring of the hose of the intercooler. I fought with it and lost. Good job.

@rp8930 2 жыл бұрын

Thank you for your comment. The disassembly of this pipe was not easy. you have to be careful not to break the small pin.

@ElRussoW12 2 жыл бұрын

Very helpful video! Thanks. Got same error today on 72.000km Will be doing same cleaning method

@rp8930 2 жыл бұрын

I am glad that the video will help you. Exactly the same cleaning method will be on 150hp or 175hp. Good luck.

@bikerszalau9328 2 жыл бұрын

Not working for Mazda 6 2.2 Skyactiv 2013 automatic

@bikerszalau9328 2 жыл бұрын

Solved by 1. Ignition ON 2. wire from jumper terminal to chassis (not battery - ) 3. Depress accelerator 5 times. (Confirmed by coil light flashing 5 times). 4. Remove link to ground. 5. Ignition off. Now be happy ;)

@rp8930 2 жыл бұрын

It's works on the negtive battery too. Keep ignition "on" is very important. Iam happy you solve it this.

@KhanKhan-lw8fw 2 жыл бұрын

A good hack

@tomhelsby5546 2 жыл бұрын

Thanks so much for this video. Code P0101-00 showing up . I will be doing the same job on my CX5 skyactive diesel, for which the local main dealer has quoted me nearly £1000. I reckon one days work, a couple of pounds on gaskets and liquid cleaners and the job is sorted !!!

@MrNiceGuy94 2 жыл бұрын

All the respect Sir for this job. You did well!

@kaapuuu 2 жыл бұрын

I had P0401(Check engine light) error few days ago , but after DPF burn it disappeared . Do You recommend cleaning EGR ? What do you think about programming EGR OFF , i heard it is recommended for this engine , basically there are no losses from it and its good ?

@rp8930 2 жыл бұрын

Depends on mileage, it will generally always be better for the engine to have a clean EGR and intake manifold. I generally do not recommend turning off EGR, if something is and works, it should be like that. Unless it breaks. But now it is possible to buy a used one and continue to use it.

@paulcallaghan3083 2 жыл бұрын

@@rp8930 Do you have any clue on carrying out a manual regen on the dpf?

@rp8930 2 жыл бұрын

@@paulcallaghan3083 full dpf regeneration can be done using a computer connected to the obd2. There are companies that disassemble dpf and wash it from the inside.

@nofusscoffeebrewing6505 2 жыл бұрын

are you based in the UK?, as i need someone to do this for me please!

@rp8930 2 жыл бұрын

Hello yes i living in Northampton.

@KhanKhan-lw8fw 2 жыл бұрын

Are you a mechanic mate

@rp8930 2 жыл бұрын

@@KhanKhan-lw8fw no, i'm not a mechanic. I do it as a hobby.

@KhanKhan-lw8fw 2 жыл бұрын

Ok cool mate buy any chance do you clean out oil pick up in the sump

@KayKay-lf9nq 2 жыл бұрын

@@rp8930 hi mate if I paid you Can you please do the same job for me thanks

@collinsmwangi3744 2 жыл бұрын

Great video. Very clean engine. I have the the same model and if I were you, I would be concerned about those droplets of coolant in the coolant reservoir. You might want to check, that this isn't related to gasket issues that this vehicles are know to have.

@rp8930 2 жыл бұрын

Thanks for coment. What droplets are you talking about?

@rp8930 2 жыл бұрын

8:40?

@collinsmwangi3744 2 жыл бұрын

@@rp8930 Hi, yes those droplets. I could be wrong but just monitor. Over short distances the droplets appear. Over slightly longer distances, droplets and coolant in reservoir may rise or even spray out through the overflow. Again, I could be wrong...but mine started this way and the spraying got worse...it was time for proper a head gasket change. Changed exhaust cam as well. Again, I could be wrong.

@rp8930 2 жыл бұрын

@@collinsmwangi3744 Congratulations on your perceptiveness. Probably because it's winter and I drive very short distances. I also have to replace the coolant I will record a video about it, it will definitely be helpful for someone Thank you for your comment

@dmc_77 2 жыл бұрын

great video mate. where abouts are you based and would you do this job on my car? thanks, dean.

@rp8930 2 жыл бұрын

Thank you for comments. I am from Northamptonshire I just recorded this video to help someone else fix that problem.

@dmc_77 2 жыл бұрын

@@rp8930 ok do you know the person that did the job then

@dmc_77 2 жыл бұрын

@@rp8930 will you do this job for me please

@rp8930 2 жыл бұрын

@@dmc_77 What city do you live in

@dmc_77 2 жыл бұрын

@@rp8930 rotherham south yorkshire

@michaela-f9389 2 жыл бұрын

Good work done. can you list the tools needed

@rp8930 2 жыл бұрын

I used basic sockets, screwdrivers, pliers, sockets extensions. No special tools are needed. thanks for comment.

@cebudave 2 жыл бұрын

Been there done that, on my Mazda 6 manafold, I was worried about getting carbon down into the engine, so didn't clean the ports out in the head, now I'm in the same situation as before 6 months later. 😢 DId you take any precaution to stop the carbon gloop from running into the engine, or did it just burn up when you started it?

@rp8930 2 жыл бұрын

Was secured with a cloth and gently pulled out. THis EGR fluid dissolves carbon very well. Air compressor for blowing. I made such a scraper out of a sheet of metal. Something must have been burned. But I tried to be careful and do it slowly.

@cebudave 2 жыл бұрын

@@rp8930 Thanks, and well done, it's not an easy job getting the manafold off a Mazda 6.

@rp8930 2 жыл бұрын

@@cebudave That's right, but doing it yourself gives you a lot of satisfaction and you save your money.

@gabsams4995 2 жыл бұрын

@@rp8930 Hi, i think that you can turn thé engine so the valves close this way you can do 2 piston then turn again and do the other 2.Great job, Nice and clear vidéo !

@kevinhancock4064 2 жыл бұрын

Another video it shows u put car in 4th turn wheels which turns crank. Use an endiscope and you'll see the it close on 2 cylinders. U can thrn clean these snd repeat to clean other 2 . I think cylinder 1 and 3 then 2 and 4

@williammillar2633 3 жыл бұрын

Great video, I have a mazda 6 same engine as yours. Can I ask the millage on your engine? I'm getting a stutter around 1700rpm which I'm thinking is egr or intake valve

@rp8930 3 жыл бұрын

Thanks for comment. I have 125k Miles. On yours can be injectors or washers on them. Very important on our engine is oil strainer very often clog up.

@rp8930 3 жыл бұрын

William also you can try clean air flow meter.

@aali2137 2 жыл бұрын

Hi, im starting to get a stutter at high speed too. Do you know exactly might be causing the engine to struggle? No dashboard lights but stuttering when accelerating.

@thekristafon906 2 жыл бұрын

@@aali2137 if you have an earlier version of the exhaust pressure sensor and haven't replaced it with the newer version give it a go part number is #SHY6-18-W00

@lulutime5846 4 жыл бұрын

Nice :)

Ең жақсы KZbin

Пікірлер