go

good😀

Is it safe to move the cam and crank shafts if the timing is already off and not even sure about the position of the oil pump shaft at time when removed belt

🤍

Wan wan!

🙌🏼

Every video got power tools 🤦🏽‍♂️ I guess basic tools don’t matter anymore

So was the pulley bad or just a stretched drive belt?

Awesome videos man, very clear and easy to understand. Thank you

You can use threadlock glue instead of replacing the bolts.

Just diagnosed this on a family members car, thank you for the video to confirm it. Guess I'll be replacing it and the serpentine.

why didn't you get the alternator, wouldn't it be easier

A big help thanks

Thanks....how much miles on the Endeavor? Mine is a 2008 with 185000 kM and I have to do this. Did you also replace the sway bar bushings? Best.

Is anybody still here?

Thank you for this video. I am about to tackle my passenger side door speaker. I'm going in a lot more confident after watching this video

very poor instructions.. there's no tools sizes mentioned

Interesting enngineering why Toro decided to use square head screws to hold down the transmission belt cover. Also I see you removed the engine bolts to remove the belt guard. DIY'ers be careful because the sometimes the head of the engine bolt will snap off.

Good job but better to tilt the mower carb side up.

Duplicated the process, 100% success, thank you for this video, was simple step-by-step and easy to follow along with !!!!

Thx. Bro! GREAT VIDEO!!

I did this to my corolla 2015 i turned counter clockwise didn't hear any clicks maybe bcz there was alot of bg noise but when i turned clockwise i did hear it release, during startup there was a sound for prob a sec assuming it was just bcz there was no oil in it now engine seems to be working fine anything i need to be worried abt thanks 👍

Great video 👍

What's a great vid mate! Well done

You do not need to remove the engine mount to do this job. I did everything from underneath. The whole job start to finish took 30 minutes (included cleanup). 19mm box end wrench with a 18" of 1 1/2 ABS pipe for the leverage works. No special tools needed.

was the tensioner in a lock position when you inserted it into the engine?

Great video thank you!

Awesome video bro Ty 👌🏼👍🏼

What size belt 21" or 22"I tried to real place my new belt is 22 but is very lose

Thanks bro!

Thabks alot friend. Saved me from buying new mower 💯

Can clean or replace connector but will corrode again. Better to solder wires to speaker and insulate.

Wow, this was great. You saved me hours of time. Thanks so much!

Sandals fam? 😂😂

Very well-done video!

awesome.

Everything was explained perfectly. Just one question. Do you need to put the engine at TDC before removing???

Wrk nic sond bad 😊

Where are you located?

What is the recommended mileage for changing the belt? 😊 ty

Thanks man you're the best, I did the job on my 2016 Corolla and I did have issues with the tensioner not compressing so I used a screw driver to hold the tab down. Also had trouble with the tensioner giving resistance when installing but I used your method of applying pressure and doing the lower one first. Everything's running smooth.

Thank you. I did this repair. It cost me nothing but time. 👍👍

I completed the Valve adjustment and as well as a new valve cover, thank you for making this video!

Thanks for the video... easy peasy ✌️

Genius idea! 😁

I like ur demonstration I work at the dealer and u chose the most complicated way of removing u don’t have to remove the alternator to get that tensioner out at all u can take the belt off from behind the motor mount with a long 19 wrench easily without removing the engine mount doesn’t have to be slow either to get the water pump pulley off u can put a bolt from the bottom between the frame and the pulley and break them loose from the bottom than remove the harmonic balancer with weighted socket and remove the tensioner from the bottom within 30 minutes lastly the water pump pulley u can push to the front of ac compressor without having to completely take it out of the engine bay with alternator installed

The airbags when they pop will be interrupted by the wire

Best explained impossible!!! Thanks god job brother

Hi bro, I am from India and I’m driving santa fe 2015 model and currently I am also facing the same problem in my vehicle, the knocking sound and vibration at the speed of 35 kmph and 55 kmph only, and the car runs fine on all the other speeds, the Hyundai service centre mechanics here are asking me to change the propeller shaft but since it’s a costly part I am not willing to do this, and after seeing the shaft I can tell you that tere were no fallen parts in my propeller shaft and it is not rusted too, yet I am facing this issue, can you please suggest something, any help would be much appreciated, thanks

This video is far better than the official video guide put out by Toro! Toro would have you needlessly removing the blade!?!