TopSkills

Пікірлер

@jimbauer6822 5 сағат бұрын

Nice to see some real quality work from your country instead of that fake repair crap

@rehanajamshed3508 Күн бұрын

👌👌👌

@MassMade12 2 күн бұрын

this is such a fascinating video! I really appreciate the detail you went into explaining the mass production process. but honestly, I can't help but wonder if this level of automation might eventually lead to job losses for skilled workers in the long run. it’s a tricky balance between efficiency and preserving jobs, don’t you think?

@PhuongNguyen-jr4mp 4 күн бұрын

Hay

@ShahzadHussain-rj5zw 5 күн бұрын

❤❤❤❤❤❤❤❤❤❤

@nathantaylor9998 7 күн бұрын

Heat treatment not required for these bolts?

@AmnaMughal-j2c 12 күн бұрын

👍

@ShahzadHussain-rj5zw 12 күн бұрын

❤❤❤❤❤❤❤❤❤

@ZygmuntKiliszewski 15 күн бұрын

Good work, congratulations and best regards ❤😊👌.

@coisasdoze2460 16 күн бұрын

Grandes artesãos, grande trabalho

@raymondjackson6069 17 күн бұрын

Fanfare for the Common Man!!

@toni5522 19 күн бұрын

io non vedo macchine cnc. siamo fermi a prima della seconda guerra mondiale.

@ShahzadHussain-rj5zw 19 күн бұрын

❤❤❤❤❤❤❤

@hammadrayanbahseen2316 20 күн бұрын

Good

@geraldreineke1348 22 күн бұрын

how do they do this type of work WITH SANDALS OR SNEAKERS ?

@flyman451 23 күн бұрын

Interesting to use the lathe as a horizontal milling machine.

@akhmadghufroni5332 24 күн бұрын

Pakistan 👍

@medias3572 25 күн бұрын

Normes 0/20 Sécurité 0/20 Production 20/20.... aux risques d'un accident grave..

@medias3572 25 күн бұрын

je doute de la précision de l'usinage. LOL

@bhattisaab1334 Ай бұрын

❤❤❤

@jackplace4912 Ай бұрын

All these processes were developed by TRW-Ross Gear Division in Lafayette Indiana. Then the whole thing was offshored to India to use slave labor.

@flouserve Ай бұрын

Trabajo sin amor, piezas sucias que van de un proceso a otro sin cuidado alguno.

@AngryAgain1408 Ай бұрын

Mad Max technology!

@3554ELM Ай бұрын

You have to fill the tubes with sand first .

@ShahzadHussain-rj5zw Ай бұрын

❤❤❤❤❤❤❤❤

@peludo2947 Ай бұрын

Alguien sabe que es eso que fabricaron?

@UlexPapov Ай бұрын

Сидят люди и целый день клепают говно. Отвратительное качество.

@keithammleter3824 Ай бұрын

Drill bit shown at 5:50 is blunt. After going about two thirds, no chips are coming out. Wasting a lot of time and energy - don't they know when and how to sharpen it?

@adrianwright8685 26 күн бұрын

No! - it had got to the bottom of the hole!

@keithammleter3824 25 күн бұрын

@@adrianwright8685 It is correct that the properly formed chips stopped when the bit got to the bottom of the hole, but it is still the case that the drill bit is blunt - that's why proper chip formation stopped. Either that or the operator did not apply sufficient axial load an i don't think that was the case. Note that a large diameter drill operates the same way as a small diameter drill, as the tip geometry is the same and in proportion. In diy work with hand-held drills and no flood coolant, using a pilot drill can be useful in reducing the axial load required, but in industrial drilling, pilot drill bits are generally not used, as plenty of axial load and coolant is employed.