Thanks a lot that really helped 😊❤

Mate, what tape you used to seal the hoses? Any special?

❤

1:13

Industrial hydrovac units are just this exactly with a built in giant shop vac. To replicate this for the homeowner, I would say just rent or buy a big shop vac aka wet/dry vacuum and use that for the extraction. I'm going to give it a go soon I think

great video! Mina accidentally sucked over water, and after letting it dry it started complaining about the Lidar turret, even though it was spinning just fine. The 9v battery didn't do anything, but disassembling the laser unit itself worked. I had already cleaned everything and even though I didn't notice any hairs or dust, just taking the laser unit apart and then together again fixed it! (I kept testing if the robot would start after each step. In fact first time it worked, it had the Lidar unit disassembled)

Thank you! This was super helpful.

Have this unit and water drains from the bottom ok. However the radiator part on top seems to be leaking and coming out over the front and not down into th drain pan.

HI Nick. Can you advise if I can put some kind of spacer in the hinge to push it closer to the latch? My latches aren't connecting.. they seem to have drifted away from each other over time. Can I adjust the hinge or do I have to move the fence panel closer to the gate?

i have a confortable mini split, new, and when it gets hot and humid out it leaks a bkue streak of blue down wall, what will fix this

Dig a trench with a pressure washer, or how to make a big freaking mess! 😂

I'm betting the notion of less physical effort is clouding your judgement.

hi!! do you have valve clearence for this toyota?

Put a shovel through a gas line. If a shovel can break the gas line then it needs to be replaced.

Superstar, took it apart, cleaned it, all working and good. Thank you ❤❤

Pretty auwsom useful ❤

Bravo for the quick and to the point video. Good skills

Thank you for this video!

Could I do 18” easily?

I'm dying😂😂

Of course this happens when it's 40+ degs out.....

question, I replace the blower resistor my on my 2016 and still not working, my blower was working but it wasn't cooling that was and still the problem, what else I should be looking, any idea? Thanks.

Nice job mate

What about the front gasket over the water bottle ? I got mine out but I have been searching for a replacement for 2 days. It was hard to get out but I got it out and it is a double layers flimsy rubber that inflates from the gas pressure to make a seal. I know that is my problem. I check on redditt and many people have the same problem and can't buy this gasket. After filling 40 bottles of water with gas , this gasket fails. It is junk. I phoned soda stream and they don't sell the gasket and won't tell me a part number. I might be able to get a new machine on warranty but they are junk and will fail again in 2 years. I wish I would have bought the old model where you screw the water bottle onto the soda stream and the rubber gasket is on the top of the bottle.. I also think a gasket on the top will stop the water from flooding out when you over gas it. On Redditt , they say you can't get this gasket. What BS. Don't buy a soda stream unless it is a screw on type, not the quick connect water bottle.

If youre making how to videos you should use this video as a template. Clear instructions. Clear video. Straight to the point. Thank you.

thank you for your awesome video, roofing master!!!

Thanks Nick! I got this error, found your video, and was quickly up and running again. I was sure this was going to be a huge problem to fix, but it was a quick fix thanks to you. I really appreciate your help!

i have a “comfee “ unit. is there a trick to getting the drain pan clipped back in place? i’m not sure if i broke it when i wiggled it out

👌

Do you take steroids?

Crazy this came up right after my Sony 4k TV did the same. I ended up leaving it off and ubplugged for a week or so and it turned back on again.

Thank you! I fixed my S6 roborock just by diaassembling the motor and sensor and turning it with 9V battere. Put it back and it works.

Is it BLUE STAR AC?

Hi i have the same model 1997 toyota forklift 42 -6fgcu15 62381 you replaced the head on my question after i replace my cyl head i need to adjust the carburetor on the fuel mixture by the battery there has no place to use a screw driver to adjust my fuel mixture i must have a early or late fuel mixture just can't find any adjustments Thank you

That's the problem dig it yourself and save 25

Legend! Finally someone who doesnt pad out their videos with crap.

Thank you! I changed the piecr ans following your tutorial I fixed it!

I use a wet / dry shop vac to suck out the build up of water and soil.

Thanks! In our case all it took was to gently rotate the LiDAR tower!

Thank you great idea worked wonderful

I agree . But too messy. Thanks for the video

Toyota 1, skippy 0

In india i have this for sale .. anyone frm india in pune or bombay do contact me if needed… awesume condition i have

I've been looking for a replacement. Can anyone tell me what kind of cell this is?

Sorry, brother man, you didn't fix the AC you fixed the cabin fan. The HVAC fan. The blower motor. It's only just three and some odd minutes but I can't get that time back.

That’s fucking horrendous

How much % hydrogen peroxide to be used 3%,6% or higher

What size piston back in it since it howned clean up

Is that bike slow it a70mm bore I believe

Thank you so much!!! I bought one secondhand off marketplace and was so sad that the stream was really inconsistent and it took about 3-4 compressions to get any kind of fizz. Had a look at my cylinder seal was sooo grubby!!! A quick wipe and it was working good as new!! Thank you thank you thank you!!!!