4 ton. Not a bad machine. mine has trouble going slow and I don't like that its 9ft wide. a newer machine is in the works for next year
@spacedoutbeard50332 күн бұрын
brother in christ... if you can't solder please don't "repair" batteries. batteries are capable of causing serious harm.
@Jimzyangles14 күн бұрын
You floated in a mini ex for that little extension?😂
@youssifjaddouh29515 күн бұрын
Hallo all i have done everything still getting a message ERROR COULDN'T PERFORM SMBUS READ 0XOO
@garymatusavige40216 күн бұрын
I'd just weld a hook you definitely know it's strong enough
@jp3eku23 күн бұрын
I'm looking at a 2000 Bobcat 873 G with 3,075 hours on it. It is a 1 owner with all maintenance records, 2 speed, high flow, fully enclosed with A/C (needs recharged he said) and heat. Deluxe control panels on each side, recent timing belt and and tensioner replacement. He wants $15,500 comes with smooth bucket. It will only be used on our farm for unloading 2,000 lb feed skids, lifting round hay bales, moving firewood and manure. Is this a good deal?
@BillWestington28 күн бұрын
How wide is your trailer?
@scrapinmaster3634Ай бұрын
Get rid of them dirt shovels get them boys asphalt shovels
@roesmith5492Ай бұрын
Good job stan, if you get the job to seal and strip. Put a wavy 〰 〰 line down the center to mess with the sober people😂😂
@dreweroticАй бұрын
Nice video👍 I’d love to see a video about the paver controls and what everything does. I can’t seem to find one on youtube. It looks like a lot goes into making everything smooth
@ThisisMindoMintАй бұрын
Some of these contractors are just horrible
@martyjohnson5453Ай бұрын
Great video Stan
@davidnull5590Ай бұрын
Anyone know why there's a joint-line in the middle of the driveway? (not the shadow from the power wire)
@ruffus492421 күн бұрын
I’d say probably because they did 2 pulls with a bad match
@rickscott4879Ай бұрын
Great job looks like Newton falls 😊
@Birk734Ай бұрын
The one guy in this vidoe that stands and looks is absolutly useless and needs retraining or to be fired....wasteful. Very poor leadership.
@user-sb4fy6ts3uАй бұрын
Should of cleaned up the edges they are so wavey
@rossnolan2883Ай бұрын
Super 😊😊😊😊😊
@roesmith5492Ай бұрын
Good job stan👍👍
@elroysuggen9821Ай бұрын
The driveway is a foot to narrow on the left side.
@stanwoomerАй бұрын
The dirt was to high on one side and didn't allow for water to run off so the home owner had us remove it. Its the same width from the fence to road
@RednecksGoneWildАй бұрын
KABOOM !
@WestFloridaTreeTVАй бұрын
Thank you so much on these videos of the duetz rebuild I’ve learned a lot I have a 863 with the same motor going to inspect the head tomorrow. Lot of blow by and white smoke. Reason for pulling the head is that and also found oil on #2 injector and #2 glow plug
@Yeshua73732Ай бұрын
You need one decent lad with you that knows what he’s doing, your doing everything on your own thats hard work
@roesmith54922 ай бұрын
Great job stan, everyone needs a Paul on the job, my misfit is a david😂😂
@ThisisMindoMint2 ай бұрын
Why was it redone? It looked fine to me or did I miss something. But good job, just subbed.
@stanwoomer2 ай бұрын
Water was sitting at the end of the driveway about 10 feet short of the road.
@stanwoomer2 ай бұрын
And thanks :)
@BlakeMerckleTrucking2 ай бұрын
I just picked up a power box identical to urs I was wondering what that valve was you were working but now it makes sense it looks like you can use it to steer to keep a straight line
@stanwoomer2 ай бұрын
Yes. that's what you steer with. I'm not a fan of the steering on the machine. I can only steer from the left side and its hard to get the machine to move at a slow pace. a new paver is in the works.
@BlakeMerckleTrucking2 ай бұрын
@@stanwoomer ive got an older powerbox and a pf400 blaw knox and a 8510 lee boy the new powerbox is just going to be used for backup but it's good to know it can make more gradual turns than just using the levers
@adam.neese252 ай бұрын
First time watcher of your channel I have taken a look at @victoryoutdoorservices there are concrete channel I do have one little question for you with the extra material that you have like extra asphalt do you take that back to the plant and dump it there for reuse or what do you do with it
@KenFullman2 ай бұрын
You sound like a stressed out guy that is just managing to keep his cool. 😁
@josunik22 ай бұрын
Did you cut the compaction of soil and aggregate from the video?
@stanwoomer2 ай бұрын
The guys didn't video it while i was gone so i didn't have that footage of them compacting the millings on top of the 2.5 inch asphalt binder where it was low
@rickscott48792 ай бұрын
Great job guys 💪
@roesmith54922 ай бұрын
Another great job stan👍👍
@roesmith54922 ай бұрын
Good job stan👍👍
@stanwoomer2 ай бұрын
Thanks roe
@AllAccessConstruction3 ай бұрын
How do you like that tomahawk?
@stanwoomer3 ай бұрын
I love it! It works great for small jobs and it's build out of heavy gauge steel. I did upgraded the wires to some heavier gauge
@SoberBassHead3 ай бұрын
Quick tip, spray your mixer with some diesel and it will make clean up a breeze
@SoberBassHead3 ай бұрын
Those steps were definitely hard to get out. The concrete company I work for never sends multiple loads in one mixer because of exactly what you said. That’s really good work right there. 😊😊😊
@mcl2373 ай бұрын
That sucks man. I have the same motor on my 873 and did mine 500 hrs ago. Maybe I should do it again
@stanwoomer3 ай бұрын
It ended up being the brand new oil pump I got from the dealer. The bearings locked up in it and caused the belt to break.
@roesmith54923 ай бұрын
😬😬Stan you can't call it a successful start to a season unless you break everything on the job, gotta work the bugs out on the first day😆😆he'll you even got your guys limping around in braces🤣🤣fleetwood was a good touch to the video, keep grinding my man👍👍👍
@roesmith54923 ай бұрын
🤫🤫Stan you should reverse the rotation of the tarp motor so it doesn't roll debris up in tarp, it'll roll over it, hade to do it on mine, great video (Stan the man)😂😂
@stanwoomer3 ай бұрын
Roe that's a good idea thanks
@prairiebuilder3 ай бұрын
Great video Stan. I used the information you provided in this video along with other videos and written instructions I've looked at to successfully revived two of my Mavic Air 1 batteries. The only thing I did differently than your method was that after I slow charged the entire battery above 12v, I removed the charging wires I soldered to those two terminals and then closed the battery back up and proceeded to use the debug board. I hooked up a positive and neutral lead to a small 12v sealed battery to activate it for programming, but it reduced the amount of soldering required and meant that I didn't have to open the battery back up to remove the positive lead after reprogramming the chip. Thanks again for inspiring me to have the confidence to do it myself. BTW I like the artist you had playing while you were testing and soldering the battery.
@coulterasphaltservicesinc62143 ай бұрын
I have this same paver you have issues with it tracking straight?
@stanwoomer3 ай бұрын
I do.It will not track straight. My goal is to upgrade the paver this year and keep the gehl as a backup.
@asphaltfordawanga3 ай бұрын
Idle that paver down and put it on low speed much better for the paver
@davidpowell99154 ай бұрын
I painted my Bobcat 331 excavator about 5 years ago. I felt the same way as you about the Bobcat paint. It was too thin for me. I ended up using Rustoleum and it did good.
@elroysuggen98214 ай бұрын
Check your grounds or ground wires, looks like bad ground somewhere for the lights.
@KiotiTractorNL4 ай бұрын
nice work buddy paid off in the end she looks good
@joeycyr69104 ай бұрын
The bobcat paint is already thinned to be put through a spray gun. Thats why the paint is thin
@roesmith54924 ай бұрын
😳😳Great video Stan, you surely put in the work on that old girl💯💯
@djlyon1175 ай бұрын
Hey Stan, do you happen to have the model number for the cold planer?
@stanwoomer5 ай бұрын
Unfortunately data plates were missing so I don't know
@roesmith54925 ай бұрын
Keep (grinding) stan👍👍
@roesmith54925 ай бұрын
Got happy when I got the notification, Stan cut me short😂😂😂
@loganthegreat69295 ай бұрын
Hows it holding up? And thank you for making this video its excellent!
@rickscott48795 ай бұрын
We were out your way Saturday. Went to the DeWalt store in Niles 😊