@@dennisdinsmore1959 because it prevents the chain slapping against the rail

​@@LukeDoorMan oh yeah that totally makes sense i never thought to try that, ive always been stuck in customers garages endlessly adjusting springs to stop the door from jerking but this might be a much simpler solution in some cases. good idea

@@johnwhittle1802 all the 1024s have the exact same spline that comes off the motor

Many thanks, Luke. Your videos have been very helpful to me. Thanks for creating them and posting them!🙏👍

@@sabinomartinez1062 either the sensor or the force is the problem, check to make sure both of the sensors are lit up solid and if they are turn up the black close force dial located under the light cover

@@LukeDoorMan thanks! I appreciate your response i will try that.

@@AdviAllen its the same one I showed before

@@TBHD724 yeah that probably isnt the smartest idea lol

Can I have the genie screw drive so you do have some room for more openers

@@JoeyKing-bl2qo buy your own ☠️

​@@TBHD724fr 💀

@@jimz6076 if the sensors are misaligned and you try to set limits on it that may happen, so make sure both of the sensors are lit up correctly

I parted that opener out and threw it away a few months ago, im still looking for one that has the case which is gonna be hard to find

@@GarageDoorGuy327 im not really planning on getting rid of my openers but I appreciate the support

@@sabinomartinez1062 im not completely sure but I think the B is older

@@rauten6588 push the learn button on the motor, then push the remote three times and if the remote is compatible it will run the opener on the third push

@@LukeDoorMan Thank you so much and for the quick response....

I had a chance to visit my friend Ken today and his problem with the garage door remote. The wall switch for unlock and lock was in unlock state. The Model is 1/2 HP was IS550/A. One remote is LiftMaster 380UT 2-Button Universal and the other is Chamberlain Remote. The LiftMaster one does seem to talk to the Overhead Signature box. I unplugged / powered off the unit and waited 20 seconds or so and then plugged/powered back on. I then pressed the reset/learn button until red light went out (making sure we were reset and good). Remotes have new batteries. I pressed the reset/learn button once and the light started blinking, press remote once and the light is then went solid red; and then pressed remote one more time and the red light goes out. Press remote again and nothing happens. But the light does have a faint flicker when pressing the remote button. Ken informed me earlier that it just quit working . Wall button still works fine opening and closing. Could the circuit board be the problem? Do I need to do anything with the remotes (they both have a button and dip switches)? When pressing the Chamberlain remote; only the blue light comes on the remote and nothing happens on the Overhead unit. Any suggestions or thoughts without taking up too much of your time. Thank you again.

@@rauten6588 for those remotes you actually need to hit the learn button on the remote before you start the programming process

@@LukeDoorMan I just got back and it all works.... since that was a universal remote, after pressing the program button, the magic number to press the button was 6 times.... Again, thank you!

@@SmoothBassVO heres a video that might be able to help kzbin.info/www/bejne/fp_NoYihj899fMUsi=d43wSqAiDr_B12fL

@@thecraftsmanguy1899 ill get to that at some point, I got some other ones I wanna do first

@@ElevatorAdventure1816 when chamberlain starting making 390mhz boards they put in something that turns the light on when the beams is broken if the door is in the up position. I think they took that feature out when they came out with their MC models

@@LukeDoorManyeah they did.

@@TBHD724 this one doesnt have that

When they take down openers usually they take the battery backups out. It would've had it originally

@@AdviAllen its the same linear I showed in my last video

@@mookjones9117 linear made some ops for precision door

@@JoeyKing-bl2qo a lot of installers around here throw junk away behind a clopay store at an industrial park

@@AdviAllen I got this opener for free

@@LukeDoorManthat is a amazing deal ❤

@@mrtbonebones3823 locate the learn button on the back of the machine (its just a round black button with an LED by it), push it once, then push the remote 3 times and it should run on the third time if the remote is compatible

@@LukeDoorMan oh wow hey thank you so much for the reply I wasn't expecting one and I really appreciate it! However for some reason my setup is super squirrely and took me about an hour and a half to finally get it ,so this is what happened,,, I have two 777CD's, I had two single button clickers that came with them, one for the left one for the right they broke a long time ago, I replaced them both with a single two-button Chamberlain model-klik5u. I needed a clicker to sync up my Hellcat to the door opener it would not connect directly and according to dodge you need to have a wireless Clicker to program the car (weird). So this is where the problems started, the left Phantom connected to button number one exactly how you said it should with no problems and this is where it gets odd ,the right side would not sync up to button two.. after about 7 Minutes of trying while balancing on a ladder that was entirely too small for what I was doing I decided to see if button one would sync up and it worked exactly how you said it should but unfortunately now I have one button working both doors at the same time only the doors were not synced up at the same time so one would open while the other would close after about another 5 or 6 minutes of my death-defying balancing act on the ladder I finally figured out how to erase the code from the right side opener! however the circus act was not yet over, the next 15 minutes or more was spent trying different button pressing combinations between the right side door learn button and the number two button on the clicker [ keep in mind that the Chamberlain also has a program button under the battery cover which was not needed to program the left side door], so to make a short story long I finally got it by a combination of pressing the learn button on the right side Phantom and the program button on the Chamberlain pressing the number two button three times then hitting the program button on the clicker again and that finally worked! Why the left side was so easy and worked like you said but the right side had a completely different set of rules I don't know I'm not sure if it's an issue with the Phantom or the Chamberlain but it was definitely weird! But either way thank you for trying to help I appreciate the reply and sorry this message was so long!lol.

@@mrtbonebones3823 those remotes do have the program button that you have to push before starting the program process, so it actually is kinda interesting that one of yours worked without pushing that button