just did my boat like this thank you!

Can’t watch anymore of that kid huffing glue! 😵‍💫

I was told you don't use any negative wires. I I almost hooked up negative and the guy said you would've blown the back of the boat off and he says he's seen it done so be very careful when you hook these up.

Can I use battery jumper cables, just the cables as PO wiring harness

Good way to lose a finger or leg with your circular saw technique. Your blade should never be extended beyond what you need to cut. , which was about 1/8". Also dont brace something with your fleshy thigh.

How much does it cost to run

Good help!

Thanks for your video. I'm enjoying my fountain now. Just wondering if I could have went deeper with the suction pipe on performance and better water quality. Ever thought about going deeper ?

Great job ❤

Than k you for your comment about the environment! Great job. What’s your son’s name?

Very cool project thanks ❤

won't you burn out the fuse if the float turns on the pump if you also manually turn it on at the same time?

If your batteries are on will your float switch still operate manually

Nice video👍Short simple and to the point.

Very helpful. Thanks!

Leave the kid out of it until he's old enough not to wanting the attention.

I miss your videos I’m buying a new Suzuki

Nice job guys. New follower. I’m going to do something similar soon.

Any updates?

Have you ever changed out the internal anodes next to the spark plugs?

a good idea is the no seize - ointments or paste.....

i love it......... you used a FLAT HEAD screwdriver to Remove the screws, then you Used a Phillip Head to reapply the screws... Funnny, but informative... THANK YOU Sir.....!!!!!!!!!!

Thank you so much. i was pondering how to do it and you solved my questions.

I bought a brand new ss250 and hit a pvc pole that was broken off right below the water and scratched up my lower unit real bad only has 14 hours on it😢

what a great idea

He’s a right little sniffer

If you trim it all the way up, makes less of a mess

The proper way to do this is to dremel out all of the spider cracks down to the point you don't see the crack then use Gel coat thickened with silica powder and fill the cracks with the thickened gel coat after they have been sanded keep your work area taped of so that you don't create unnecessary work for yourself. Keep the fill area as level to the surface of the gel coat as possible for less sanding. You can buy gel coat that matches your boat bt serial # Total boat paint co.

Best get some tension on those Jack straps… Those boats are heavy

Thank you for the video. Just bought a Yamaha 115. Another favorite channel is Dr. Shawn Baker. He will set you straight.

May I suggest to improve the full draining of all contaminants, ease of removal of filter, run the engine to operational temperature on the flushing muffs. Also for the sake of the bearings and pump, please fill the oil filter with oil prior to fitment, so the paper element is soaked. You fill when you start to do the draining process, the oil soaks into element and there is barely any to spill when fitting. Starting on a dry filter creates a situation whereby oil pressure takes a while to build and bearing surfaces can get damaged.

could have been better explained, so that your explanation matched your drawing. Just connecting the negative posts of the two batteries would produce a common ground.

Why not put in a unit with an internal float switch?

Thank you. The color of gear lube wasn’t black liter engine oil. Is that the normal color? Mine looks the same color but I thought that means water in it? However sitting overnight didn’t separate so maybe that’s ok.

Your kids are all fisherman even your little girl great kids I tell people all the time get SEATOW ITS WELL WORTH IT

Which NGK plugs did you use?

Where did you find that pump to purchase? What HP is it?

Is it a standard size spark plug socket? Thanks for the great videos. Mine has not been running smoothing (surging and bogging down) despite new fuel and filter so I'm gonna try to change out the spark plugs this weekend.

I think I'd prefer a minumum 3/4 hp (1hp=746w) with overload protection. But IMO I'd pay a little extra for a better model pump. Remember, GFCI ONLY protects from ground fault, NOT an overcurrent/overload condition. Must keep filter clean. If the pump fails it has already been running at higher amps, motor windings heated and fused, etc. If really wanted to protect from overcurrent/overload, as an added protection put an inline fuse holder and fuse in a larger 4" receptacle box with the GFCI (maybe 8-10 amps).

Great vids! What grade fuel do you run 87 or 89? Many hrs on the motor?

Where do u purchase your gaskets from?

Another question for you. I got the same kind of pump (9000gph) and someone who I trust told me if I put a cap on the top, like you, I would restrict the water flow and burn up the pump. Have you experienced anything like that with your setup?

I also made your fountain and it works great but I was just wondering why do we reduce the pipe from the pump 3” to 2” then the nozzle back to 3”??? Could we just stay at 3” straight up to the nozzle??

Thank you sir. Sweet and simple. Thumbs up!!!!

What's the capacity?

On the pond pump how many gallons per hour pump did you purchase for this project ?

I am in desperate need of some guidance for my pontoon. I have 5 batteries total. I want to make sure they are all hooked up correctly. I have 4 things but possible 5th that’ll require power. I have one Pecko 2 way switch already installed - 1, 2, All and OFF. I also have 2 onboard battery chargers. 1 is 2 bank and 1 is a 3 Bank. I can send pics or specs if needed. 1. Motor/ignition 2. Trolling motor 80lb thrust 3. Garmin Depth Finder 4. 8 speaker w 2 12” subs stereo 5. Possible re-hook up bilge pump Main ? Is how to hook up all of these appropriately if you can give any advice I would be forever grateful!

Thanks. Good info but I thought you put the plugs in backwards?

Did you sand the area before using the filler and what grit sandpaper did you use to sand the areas with the bigger gouges?

are they pre-gapped?