You got me laughing!!! This crap works!! Thank you sir!

I would agree with the $4* one( cycling thermostat) being the problem normally when the High Limit trips. Did you check the temp it cycled on after putting the old one back on?

Invests all their money on saws but not common sense PPE. This video is a prime example of a unprofessional tree service and how not to become the statistic. Also educate yourselves on rigging forces when anchoring a portawrap to a dingo..

Do you have any courses on how to do this?

hey buddy thanks for the inspection on the leak, was about to buy one over here in nova scotia, but not if it leaks. turns out your's is fine. buying it now! thanks bud!

Just bought one brand new regulator was broken out of the box. What a joke. Returning it.

Like to see the pressure after sitting overnight.

What is part you bought? Send link

You're right. People say that if the continuity checks out then it's good. This is not always accurate.

❤ hello thanks for posting this I have practically the same type of dryer that's doing exactly the same thing that you describe I got my back cover off and it looks exactly the same like yours. It's heating for a couple of seconds it shuts off and I think I have the same exact problem so I'm going to go and get the parts and see if this fixes it thank you

Yeah, I changed the same component but, my clothes still came out damp & wrinkled.

Would that cost the dryer to run hotter if the sensors is not good ?

It’s called a cycling thermostat and high limit cut off packet. Cycling thermostat was the culprit here.

thank you I have this ordered for my 99 Dodge

I got a repair kit on amazon all 4 thermals switches and a heating element for a out 30 bucks

thank you for the video good sir.

I had the same problem you did, in my case it was real easy,once i took the back cover off that resistor was hanging off by the cables,it had detached completely from the heating element housing and the plastic/bakelite housing was cracked in several places, a no brainer, ha ha ha

So why can't you just replace the cutoff?

Just get to the fix. Don't need a backstory to everything

Ty for the video! You confirmed my suspicions. I think maybe that pc goes bad over time bc it gets easier & easier to make it hot enough to kick out. So it ends up kicking out way to early. But in theory still works so continuity checks out. Newaz thx again!

Thank you for taking the time to help DIYers like me.

Still helping people with this vid. Thanks.

I just changed all of my sensors and my heating element comes on for about a minute then shuts off. Any ideas how to fix it?

I had the same problem, additional problem was that it would take a month and $100 to get a new switch from the appliance store. I took a toothbrush and cleaned the switch and the element. I put it all back together and the dryer is working great! Thanks for the video

When you do the wire modification on the lower one, arent you left with one wire disconnected? Could you show me what wires go where?

All my stuff is located in the front. I have an older kenmore.. it sucks

don't forget to check the vent discharge on top of your /my roof if it 's on your roof "for blockage"

Question...I have a situation. When my dryer starts the flame would kick on but then after a few seconds it would turn off...then after a few long seconds maybe a min or so it would kick back on then in a few seconds will shut off....any thoughts on this??

Is this thermostat thing the same with a gas drier?

Thank you Sir, your video help me very much. It kept me from getting ripped off by a appliance service technician. Live and learn 🤔🤔

My Dryer runs and gets hot, but after about 15 minutes it just stops. I can restart it after it cools? any suggestions.its about 15 years old. Inglis by whirlpool.

Mine must be running hot because it blew the breaker. Now it just 110 when I tested the receptacle. Thanks for your video sir

Great advise you tha man

In all of these videos I have never seen anybody reading the schematic that is usually folded up in the top of the dryer. It shows the names of the parts ant the colors of the wires connected to them. Over-temp thermal switches like the ones mentioned here rarely open and close like the operating thermal switch on the vent does so I would have replaced them both. I had the heater contacts in the timer switch and the contacts in the operating thermostat welded together and or sticking closed. The operating switch should open when the air coming out of the drum reaches about 150 degrees and lets the timer advance until the temperature drops to about 125 where the operating contacts close again to energize the heating element and allowing only 120v to be across the timer that needs about 240v to operate. As an electrician it drives me nuts too but if you have the same voltage on both sides of an appliance motor it doesn't turn and is off until the contacts in the operating switch opens and the motor sees about 240v through the heating element and advances a little bit until the air coming through the drum is cooled enough by the wet clothes to cause the operating thermostat to close it's contacts, sending voltage to the heating elements and causing the timer motor to only see the phase 1 or A on both sides of the motor and stopping it from turning and advancing the cams in the timer. I was able to separate the contacts in the timer switch and file them flat with a jewelers file and put a thin film of vaseline on them and the other contacts, as long as I had it open but the operating thermal switch is a replacement part. You can test thermal switches with a heat gun and a meter but wear gloves.

Thanks,thanks and thanks.I had a similar problem and almost gave up after 3 weeks of trying and testing everything in the dryer.i saw your video changed the thermostat and it worked.THANKS.

I have an Amana commercial dryer and it shuts off after doing many loads. I wait about a half hour then everything is fine again. I don't know if that is normal but maybe its supposed to do that to prevent it from overheating snd starting s fire. My wife washes many loads of clothes every 2 weeks. Maybe she should dry the clothes less time or not make the dryer work so much. I don't know if anything is actually wrong with the dryer or the safety mechanism is actually working. the heat is fine and it drys the clothes well. She does about 10 loads. After 3 loads it stops working and she waits the half hour. She has to do this after every 3 loads of clothes to dry. So it takes all day. Do you think something is wrong with the dryer or are we overworking the dryer? Thank you.

Thankyou

while watching this i witnessed my dryer click off & now it won’t turn on until it feels like it 🤦🏽‍♀️ thank you so much

He changed but hopefully it can be more concentrate and clear.

Thank you .

Thanks for the great content in this video. It's very helpful

Apologizes for my offence, I really love your channel and I'm also a fan of DIY. I wanted to see if you' d be interested in adding the affiliate link of 279838 dryer heating element under your video. I created the coupon code with 5% off to benefit your subscribers. Meanwhile, I am glad to pay you an additional fee to thank you for promoting our products. I am representing a brand US amazon store, We're appliance repair replacements Amazon seller. Our vision is to become the global leading brand. Here is my email: [email protected]. lf there is something that interests you, please email back and we can discuss the details more in-depth. Hope to hear from you soon. Thanks and take care, Amy

How do you hook jumper wire on thermostat

Friend ThE problem is that you not show the problem before change the elemento.

...so long story short...it’s one of the resistors that’s could be the culprit of the element short cycling...okay

Thanks for the video. I was able to fix my dryer and figure out what was wrong using your video. I’m a 66 year woman that need to fix the problem myself in the middle of the coved 19 virus. Trust me I need my dryer. Stay safe Joe. Take care

I have the issue where my dryer heats up but never heats up all the way it barley gets warm but the element cycles.

This videos nails its , tests for temperature limitations m.kzbin.info/www/bejne/jXulaYxoqc-ModU

The device at the top is a thermal fuse. When it opens, it is ruined, or open. It must be replaced.

🔥🤟🏽🤟🏽🤟🏽