Hill Country Livin'

Пікірлер

@cowboybratt 2 күн бұрын

How do u adjust the bevel?

@iringapaikea1381 9 күн бұрын

Hi, i have a question. I own the exact model shown in the video. Same problem, but in the 4wd leaver. Owned it for a few months now and haven't been able to get it into 4wd. Would it work if I done on that side?

@hillcountrylivin 7 күн бұрын

@iringapaikea1381 I love questions like this. However, without seeing how the lever is behaving, I don't know what to tell you. Is the lever moving, but not engaging the 4WD? Or is it just not moving at all? If it moves up and down, but doesn't engage, then I'd trace along the linkage, starting in the console to make sure that all of the links are connected together. I sure hope this helps. Please let me know the outcome.

@tw8126 24 күн бұрын

Awesome video. Thanks!

@humbertoluna3050 28 күн бұрын

Thank yoy

@charlesjacksoniii8787 Ай бұрын

I am a carpenter by trade and I have this saw and matching stand its great I use it for trim carpentry and home improvment projects.

@jasonwoods3384 Ай бұрын

Nice I gotta pee now. Lol

@hillcountrylivin Ай бұрын

Hahahahah! Thanks for watching!!

@AbbasMohamadi-ei9ww 2 ай бұрын

❤❤❤❤❤❤❤❤❤

@jeannetterivera8530 2 ай бұрын

❤❤ thank you for video , you made it easy.

@hillcountrylivin 2 ай бұрын

I'm glad to have helped you out. Us Wrangler owners have to watch out and take care of each other!!

@88rushrocks 4 ай бұрын

Jeep said that I needed to replace the transfer cable that cost over 300 dollars and that’s not including labor so I ended up on KZbin and fixed it for 15 dollars lol and jeep said it couldn’t be fixed yea right

@hillcountrylivin 4 ай бұрын

The stories I could tell. Jeep "stealership" repair shop tried to sell me transmission cooling lines for $150 each. I told them they were sold in a set for about that price. Shop labor brought the price to around $450 all said and done. Bought them online and did the job myself. Only additional tool I had to buy was the key to remove the lines, cost about $15.

@SaveAPennyBustANut 5 ай бұрын

Is that a low profile 1/4 rachet? Amazon has the older and newer model. $20 That's such an amazing deal!

@hillcountrylivin 5 ай бұрын

It is. It's a nice kit to keep around the garage, home or office. I use my SAE and Metric sets all the dang time! Thanks for watching and for the comment.

@Pete-from-Tn 5 ай бұрын

Will that same bushing work if its the one on the transmission ?

@hillcountrylivin 5 ай бұрын

The Dorman package was labeled that it was for the transfer case. However, For that link I actually used a Dorman 14055.

@etaup02 5 ай бұрын

Thank you for the video. This was exactly what I was looking for. Saved me time and money

@hillcountrylivin 5 ай бұрын

@@etaup02 I’m really glad to hear that

@etaup02 5 ай бұрын

@@hillcountrylivin I have one question for you. My gear shift selector wont move at all when i push the side button on the gear shift selector. I was able to more the console following your instruction. The cable and bushing is connected to the spindle. Do you know what could cause the gear shift selector not to move?

@hillcountrylivin 5 ай бұрын

@@etaup02 Man, that's tough. I assume the spring mechanism on the button is working. If so, it could be related to an electrical issue. Maybe the brake light switch. Check that your brake lights come on. Or it could be the shifter interlock solenoid. The brake light switch should be located somewhere above the brake pedal, and the interlock solenoid will be inside the console on the side of the shifter. I wish I could be there with you to track this one down.

@hillcountrylivin 5 ай бұрын

One more thing I forgot to mention, there should be an over-ride switch that you could access without taking out the console. Check your owners manual, since I'm not sure of the year Jeep your working with.

@Pumpkinhead2400 6 ай бұрын

You’re a lifesaver dude! Liked 👍

@hillcountrylivin 6 ай бұрын

I'm glad it worked out for you!!

@CHASINLIFE247 7 ай бұрын

Fantastic video on how you don't have to remove the entire console in order to replace the bushing. Saved me a lot of time and effort. Thanks!

@hillcountrylivin 7 ай бұрын

I'm really glad it was able to help you. Thanks for watching and for the comment.

@GeorgeSkeet 7 ай бұрын

My truck is 2017 dodge 1500

@chinyzzz 7 ай бұрын

How can I cut crown moulding and base board with this saw.

@hillcountrylivin 7 ай бұрын

I would think very easily. Just know what your cut angles are and measure the length very carefully.

@deborahmarie6827 7 ай бұрын

So luckily mine was still intact under the console. It turned out to be the one under the car which had slipped off the spindle. So it was a much easier fix😊 but thanks for sharing,this is new knowledge definitely going to be put to use! Blessings friend 🧡

@hillcountrylivin 7 ай бұрын

That's awesome. I've actually had to do both. I guess it depends on if you like crawling under the Jeep, or tearing apart the console, huh? Glad you got it handled and didn't have to go to the "stealership".

@greenroomproductionzMBE 7 ай бұрын

Your a life saver friend

@hillcountrylivin 7 ай бұрын

I'm really glad to hear that this helped!! Thanks so much for watching and for leaving me this great compliment.

@GuyForrest 8 ай бұрын

Awesome!!! I watched a bunch of idiots videos showing how to do this including one that had you take the front tire off! This became a 5 minute fix after watching your video. THANKS!!

@hillcountrylivin 8 ай бұрын

I know, right? Why make it harder than it has to be. I went that route myself, until I finally realized what was broken. I'm glad it was helpful and worked to get you back "in gear". LOL! Thanks for watching and for leaving me this great comment.

@deborahmarie6827 7 ай бұрын

Thanks a bunch! I'll try this once I get the part😊

@hillcountrylivin 7 ай бұрын

@@deborahmarie6827 It can be a bit "tricky" getting the bushing on the spindle. Be careful not to let it drop down into the console. Please let me know how it works out.

@cinemasanders977 8 ай бұрын

Great review and instructional! Got one arriving today from Home Depot. On sale at $249 now, so I had to snap one up.

@hillcountrylivin 8 ай бұрын

Thank for watching and I'm super excited to hear that you got a bargain too!!

@adaleparker1956 9 ай бұрын

How many miles did you have before you needed to replace them?

@hillcountrylivin 9 ай бұрын

Roughly 96,000

@norman7179 9 ай бұрын

Mine needed replacement at 21,000 miles. A/C condenser needed replacement at 23,000 miles.

@hillcountrylivin 9 ай бұрын

@@norman7179 Holy Cow! I didn't start replacing parts on my 2015 until at least 50k. Weird, huh?

@norman7179 9 ай бұрын

@@hillcountrylivin The truck has never been abused. Over ten years old and a bit less than 24,000 miles. All maintenance is up to date.

@hillcountrylivin 9 ай бұрын

@@norman7179 I don't know what the percentage would be, but I do believe that every once in a while a defective product rolls off the line. Sometime the problems can be corrected, and other times it's just a continual source of problems. I hope that's not your case. I suppose you just have to decide how much investment you're willing to put into it. I think everyone has been in that situation from time to time.

@MrHexxus07 10 ай бұрын

Cool way to keep them all together

@hillcountrylivin 10 ай бұрын

Yes, it is. Keeps them all together and from rambling all over the place. Thanks for watching and for leaving me a comment.

@satanic_titanic 7 ай бұрын

@@hillcountrylivin and what of this case is cheaper?

@AubreyAbarquez-nw1pi 10 ай бұрын

can you install laser guide on this unit? thank you sir!

@hillcountrylivin 9 ай бұрын

That's a good question, unfortunately I'm sure if you could or not. Not sure how accurate it would be. But, I appreciate you watching and for leaving me a comment.

@62169michael 10 ай бұрын

How the hell did you push that back on there? I got the bushing on but can't get that black cable connector over it

@hillcountrylivin 10 ай бұрын

If the cable won't slide over the bushing on the spindle, take the bushing off of the spindle and insert it into the cable, then slide the whole works over the spindle.

@62169michael 10 ай бұрын

@@hillcountrylivinit took a few tries but I got it on. Thanks for the helpful video

@hillcountrylivin 10 ай бұрын

I'm really glad it was helpful. We Jeep owners need all the dang help we can get!!@@62169michael

@benprestridge6787 21 күн бұрын

@@hillcountrylivin this was a big help for me today, thanks!

@720erik2 10 ай бұрын

Just pulled this section apart and my original spindle is still connected and the bushing is in place….now what?

@hillcountrylivin 10 ай бұрын

It could be the bushing on the side of the transmission case. We've had to change out both. You'll have to get under the Jeep and reach up on the side of the case on the drivers side. You'll see the linkage where it connects.

@dashfish0 11 ай бұрын

Nice solution. May I know your vice size? I’m looking for a vice good for 2x4 lumber.

@hillcountrylivin 9 ай бұрын

It's just a small table mount workshop vice. If I were you, I'd go to the hardware store near you and check out the sizes that they have available. Thanks for watching and for your question.

@saityavuz76 11 ай бұрын

Excuse me, were you happy with how it handled? If so, I might want to do the same.

@hillcountrylivin 11 ай бұрын

Yes, for the way I have it set up and for what I use it for, yeah, I'm happy with it. I really like the Pegasus benches. The clamps are crap, but the workbenches are solid as can be.

@saityavuz76 11 ай бұрын

@@hillcountrylivin I appreciate it, thank you very much!

@michaeljackson2106 Жыл бұрын

I think I have this problem got many codes with two different Purge valves. One day po440 and the other say po456

@michaeljackson2106 Жыл бұрын

What's the name of the part

@hillcountrylivin Жыл бұрын

That can be frustrating. You can pick up an inexpensive code reader on Amazon for around $40 that could give you more information.

@hillcountrylivin Жыл бұрын

@@michaeljackson2106 In my case, it was the integrity module, but it depends on the vehicle and what part has failed. It could be a simple as the gas cap. Or it could be as severe as a cracked fuel tank fitting. I've been down both roads myself.

@Stockwellgreetings Жыл бұрын

thanks!

@robira1313 Жыл бұрын

The biggest problem I have with this saw is the blade changing! What a pain! Just trying to get access to the bold that holds the blade in. I'm still fighting it! I have loosened the bolt you talk about at 7:32 and it still won't lift up to give me access! aaargh!

@lightningchasersproduction236 Жыл бұрын

Awesome tip! Had exactly the same issue on my jeep. A million thanks to you! 🙌

@hillcountrylivin Жыл бұрын

I'm glad it was able to help you out of a jam!

@tdoti101yt Жыл бұрын

Excellent, thank you!

@hillcountrylivin Жыл бұрын

Glad it was helpful!

@ageingungracefullypushingt7135 Жыл бұрын

Got the same code for my 2009 Jeep Liberty. In my case all that was needed was a thorough cleaning of the gas cap/gasket and the area on the filler spout the gas cap screws into and fortunately, that was all that was required to fix the problem. Check engine light is off, Liberty passed the emission test last week. Best advice I received about my Liberty was to thoroughly clean those two areas.

@hillcountrylivin Жыл бұрын

I've experienced that as well. I fact it's the first thing to check before anything else. Most common point of failure on most vehicles and the least expensive to repair. When it's not the fuel cap, that is when the adventure begins! Thanks so much for watching and for leaving me a comment. I really appreciate it.

@micaonyx5301 Жыл бұрын

Some people are natural teachers. Your instructions were very clear and detailed, thank you so much.

@hillcountrylivin Жыл бұрын

Thank you so much!!

@geoffkeller5337 Жыл бұрын

Good video and thank you for sharing.

@hillcountrylivin Жыл бұрын

Thank you

@NoorlgUddin Жыл бұрын

I was about to tow it thinking its a transmission problem

@hillcountrylivin Жыл бұрын

That crossed my mind as well, until I dug into it. I'm really glad this helped you.

@NoorlgUddin Жыл бұрын

Love ya bro thanks

@moviegirl45 Жыл бұрын

someone lost this yesterday at a pawn shop. They had to sell it.. so I picked it up for $200! great review!! BRAND NEW!!!

@hillcountrylivin Жыл бұрын

That is AWESOME!

@perlacampos5904 Жыл бұрын

Brand new tool for this girl, everything that I needed to know I found on your video thank you.

@hillcountrylivin Жыл бұрын

Wow! I'm so glad it was able to help you out Perla! And thanks for the awesome comment too.

@SanjayKumar-tw4np Жыл бұрын

Cost

@hillcountrylivin Жыл бұрын

At the time I purchased this it was $139 and came with the work stand as well.

@mosesmoua2012 Жыл бұрын

Thanks for the review, just purchased one and sure was helpful.

@hillcountrylivin Жыл бұрын

I'm glad it was helpful. Thanks for watching and for leaving me a comment.

@jocelynbeauregard4456 2 жыл бұрын

Does it cut a 4x4 easily?

@hillcountrylivin 2 жыл бұрын

Yes, it does. I've not had any issues at all. Thanks for watching.

@ronin5979 2 жыл бұрын

Did you seriously just do a review and not use it!? 🤦‍♂️

@tobytootimes7639 Жыл бұрын

Honestly, what would him cutting a piece of wood show you? The blade spins, you bring it down, it cuts through. That’s what all miter saws do.

@lexieandpapa 2 жыл бұрын

This was the best explanation of a tool I have seen in a long time. It was very clear, concise and his talking speed was perfect and easy to follow. Thank you.

@hillcountrylivin 2 жыл бұрын

Thanks, I appreciate the awesome feedback!

@rayaldridge2506 2 жыл бұрын

Good review. But you must have a different model than mine. Mine weights 30 pounds not 25 pounds and mine is 25" x 31" not 27" x 37". Are you sure there's only coffee in that cup you're holding? ;-)

@hillcountrylivin 2 жыл бұрын

Haha! I'll have to check on that coffee!! Thanks for the comment and for watching.

@sparkyclown5161 2 жыл бұрын

I have an older 715 and the angles between stops has a cam lock to hood in place. This one looks like the knob screws down to snug it up instead of the push down ?

@hillcountrylivin 2 жыл бұрын

Yes, you are correct. Having a cam to lock down would be better, in my opinion

@garyabc 2 жыл бұрын

Good idea with the vice mount. Thanks for the review.

@hillcountrylivin 2 жыл бұрын

I'm glad you found it helpful. I'm working on mounting a bench grinder to it. It's a bit complicated but keep an eye out for that one. Thanks again.

@Momoka7 2 жыл бұрын

Yeah, I keep pondering do I really need a Miter Saw. I plan to make some furniture. I looked at the sliding variants but the main thing I want to cut is thin pieces to length possibly longer pieces, for which you would need a sled to cut on a table saw and then if the piece is a little longer even the sled might not be good enough. I decided against a sliding miter saw early on, the reason I don't want a sliding variant is that if a piece is wide enough I can run it over the table saw or use a track saw, plus the added depth you would need. I plan on making a dedicated table at a wall so I not want a more compact saw. Home Depot has this saw for 199 right now, and I know Lowes had a deal with the Stand, but not anymore.

@hillcountrylivin 2 жыл бұрын

I know the different jobs have different needs, that's for sure. I appreciate the comment. Let me know what you end up doing.

@alexjaybrady 2 жыл бұрын

thanks!

@hillcountrylivin Жыл бұрын

Thank you!!

@MelI-zm9lj 2 жыл бұрын

Not much of a review when you don't use the product on camera.

@hillcountrylivin 2 жыл бұрын

I’m sorry you’re disappointed

Ең жақсы KZbin

Пікірлер