So as that you could accurately adjust value timing, fine tune ignition through to detonation. .. Maybe 🤔
@G_isuzu26 күн бұрын
It measures the heat of the cylinder head
@G_isuzu26 күн бұрын
It measures the heat of the cylinder head
@mmdsphi4434Ай бұрын
on top🔥
@jorgecancina1085Ай бұрын
el mejor motor el Perkins 4
@G_isuzuАй бұрын
👍🏻👍🏻
@mehdijashoogri428Ай бұрын
عالی 👍
@G_isuzuАй бұрын
😍🙏🏼
@niklasmunko6987Ай бұрын
Er macht den Kolbenringsitz sauber
@G_isuzuАй бұрын
Yes♥️🙏🏼
@G_isuzuАй бұрын
Our specialty is in truck repairs
@vexensweat52332 ай бұрын
Thermostat. Chooses when the coolant can pass out the engine into the radiator once it gets to temp
@franokerman2 ай бұрын
Cigarette lighter
@Biker9212 ай бұрын
Android valve.
@Biker9212 ай бұрын
Anaroid valve
@Dien6Amie2 ай бұрын
Thermastat
@RandyTerrell71742 ай бұрын
That's a fibulousmimulator
@G_isuzu2 ай бұрын
👍🏻👍🏻
@steveo60342 ай бұрын
Thermostat?
@G_isuzu2 ай бұрын
Yes👌
@teddbrown42622 ай бұрын
This ain't a gasket
@G_isuzu2 ай бұрын
👍🏻
@penname56232 ай бұрын
"If you have to ask, Big Man, you can't afford it" Barry!
@G_isuzu2 ай бұрын
👍🏻
@anomyouslastname49042 ай бұрын
It’s a bearing. When the valve goes up and down, it spins a little every time. That gives a place for the valve spring to rotate without scaring the head.
@G_isuzu2 ай бұрын
Yes👍🏻
@abdolaliebrahimpourgorji63622 ай бұрын
Good luck 💙💙💙💙
@danilopia12962 ай бұрын
😀😀😀😀😀
@danilopia12962 ай бұрын
👍👍👍👍👍👍😀😀
@aligorji-cv6jz3 ай бұрын
ماشالا برار👍🏻👍🏻
@user-fc9ru6vp3p3 ай бұрын
چرا روي زمين كارمكني
@danilopia12963 ай бұрын
😁😁👍👍👍👍👍
@user-nd1wg8ru8q3 ай бұрын
عالی ❤
@danilopia12963 ай бұрын
👍👍👍👍👍👍
@PaulHigginbothamSr3 ай бұрын
It's called a valve guide seal installation. With faulty valve seals you will leave a trail of smoke wherever you go. If you work on heads you must put new valve seals in because they can get brittle in a hurry.
@user-ld2gj9tn2v3 ай бұрын
❤❤❤❤عالی
@wyliecoyote13 ай бұрын
Looks like a diesel cylinder head. Four cylinder Perkins or something.
@G_isuzu3 ай бұрын
Yes, exactly What is your specialty?
@JohnnyAFG813 ай бұрын
Testing for stuck valves.
@G_isuzu3 ай бұрын
Bravo
@LikeAGentlemanPlease3 ай бұрын
Looks like safety is for pu😺🐱y’s!
@winstonholmes55664 ай бұрын
Did you try using a welder to extract the broken bolts/studs ? I have good luck doing it. Can’t remember the last time I had to use the drill
@G_isuzu4 ай бұрын
Yes By the way, we extracted the rest of the screws and welded them. This part is very old and the surface of the part was cut much lower.
@winstonholmes55664 ай бұрын
@@G_isuzuI mean use a welder to weld onto the broken stud and build it up so you can either vice grip the weld or weld a nut onto it to turn out the remaining broken stud/bolt.
@keenankendall91054 ай бұрын
Promo*SM 😊
@G_isuzu3 ай бұрын
❤️🫱🏾🫲🏼
@user-el5ju3fk9k4 ай бұрын
Perfect 👏👏
@user-el5ju3fk9k4 ай бұрын
👏👏👏
@user-tt8ot6pz7z4 ай бұрын
Краска или лак наносит
@G_isuzu4 ай бұрын
Thank you, my brother
@tomapalvtec4 ай бұрын
I mean I have used Copper spray before on a head gasket But thanks for the new terminology it shall forever be a block/head washer from here on !!!