Will be following as I have a 73 aquasport 196 that needs a transom rebuild. Trying to decide if I want to close it in. I noticed you decided to cut the outside of transom out bs the inside. Any reasoning on that? I see a lot of people cutting the inside out to reinforce the transom and stringers.
@billscreations199915 күн бұрын
@@Jakedasnakemr2 i already rebuilt the deck and stringers which is why I cut it out from the outside rather than the inside.
@Jakedasnakemr215 күн бұрын
@@billscreations1999ahhh gotcha! Well looking forward to the progress
@airvine91Ай бұрын
What was the filter where the pcv goes for?
@user-uc3ig9zo8d2 ай бұрын
How does it mount my 411 pcm don’t fit in factory bracket on my 96
@rickr20292 ай бұрын
I am thinking about doing the same as transmission mount is suffering from the oil leaks. But my question is, should the fittings in the radiator be plugged?. THANKS!
@freedom4all1083 ай бұрын
Need a post test report for live fire.
@GarySaint-xm6tr3 ай бұрын
FYI, a direct oil cooler will not fit on a 4x4. The front driveshaft is in the way. A remote oil cooler is made for four wheel drive vehicles that fits on the driver's side where the extra battery goes
@stevelassetter30722 ай бұрын
Nope! You just get the shorter oil filter and it fits fine!! Or if you have a lift kit a regular oil filter fits just fine. Did it to my 93 k 1500 z71
@dkemp13372 ай бұрын
part number PF454 ac delco filter
@RCSmith903 ай бұрын
Appreciate this video man. Trying to do this to my 96C1500. Looking forward to the next vid on how to complete this.
@Ratmeister.3 ай бұрын
Thanks Bill
@dannygilmer3 ай бұрын
Where did ya get pin out and what software did you use
@brandonsmith3403 ай бұрын
I'm doing this on the next nice day out
@ubaldomares43154 ай бұрын
Can’t the oil cooler failing cause the coolant and oil to mix ??
@americanwhiteboy7152 ай бұрын
Yes I'm having that issue now
@dkemp13372 ай бұрын
definetly helps with diagnosing a headgasket since its out of the scenario
@Chevro916 ай бұрын
Tell me what the two green wires are for why they need to be tied together and which pin on the 0411 connector does it slide in
@victorthecarguy31267 ай бұрын
You may want to reconsider the gasket under the filter adapter. If it ever falls apart you're going to have a bad day. Any leakage is internal it just bypasses the filter just like when it's cold and goes through the bypass. Before everyone panics at the thought of unfiltered oil don't forget the small blocks didn't even have filters for 55-57.
@billscreations19997 ай бұрын
I believe It was a steel-backed gasket
@stevelassetter30722 ай бұрын
Exactly!👍🏼👍🏼
@therealblakekirkham57018 ай бұрын
Did you have to tune it to get it to start?
@danludwig36798 ай бұрын
Do you need to drain all the oil first?
@tomm44323 ай бұрын
No I just did this yesterday and lost less than a quart. You only loose what’s in the lines and filter
@jorgeguzman3729 ай бұрын
How can you tune the balck box??
@vinman10298 ай бұрын
There's not much you can do. I had firmer shift points put in and removed the vats.
@ElCheyenneazul5.710 ай бұрын
Can anybody send the link so I can find this computer and the tuner
@Coldgameeee101 Жыл бұрын
Do u have to plug the radiator after
@billscreations1999 Жыл бұрын
No sir you do not
@letsgomicroliving_1993_ Жыл бұрын
So the bolts didnt come with the adapter
@billscreations1999 Жыл бұрын
No
@toddlinebarger7176 Жыл бұрын
Just did this on an 88 115hp. How did you bypass the low oil alarm?
@billscreations1999 Жыл бұрын
I unplugged the whole oil injection harness and there is no alarm
@rockfordhx2768 Жыл бұрын
How’s the truck run without the oil cooler ?
@billscreations1999 Жыл бұрын
Runs like normal but Gets better oil pressure.
@jimh7135 Жыл бұрын
How did you do it
@victorhinnant8711 Жыл бұрын
What company you ordered the oil filter adapter and gasket from?
@billscreations1999 Жыл бұрын
Melling
@connordean9885 Жыл бұрын
What is lex tech info I would like to contact him I have a 97 obs 350 in it an wanted to do the conversation from black top to 0411
@dannygilmer3 ай бұрын
In almost done changing my 96 ton to 453 . Any info greatly appreciated
@justjim97232 жыл бұрын
did the headers make a big difference in mileage and performance of your truck?
@kevinhumphrey9322 жыл бұрын
How do you wire the 411 pcm for the cam signal reference what is being used for the cam sensor thank you
@sicsam2232 жыл бұрын
You use a stock tune from a express van with a 350
@kevinhumphrey9322 жыл бұрын
@@sicsam223 thank you for the reply
@willygarcia47642 жыл бұрын
Easiest way is to get a bcm that has that feature and other features programed not everyone wants to deal with all the nonsense computer thing easier faster than paying a tuner to add that feature and charging like 200 or 300 dollars
@baileyintwert49702 жыл бұрын
Nice,I wanna do the same to my truck. Have you made your own pinout? Ive looked at two different one guys have made and theres a lot of small stuff I dont understand.
@Chevro916 ай бұрын
@Lextech on the gmt400 forum has all the charts and can get one from Him for any year swap
@christopherdalley4112 жыл бұрын
When ya swapped the PCM from black box to 0411 did the key fob to open the doors still work along with the AC, and the 4x4?
@billscreations19992 жыл бұрын
My last truck did not have 4x4 but everything else you mentioned did continue to work.
@The386mario2 жыл бұрын
So u running 2 oil filters
@hb5914 Жыл бұрын
No, he is only running one oil filter on the Melling oil filter adapter he installed.
@Lifesmasher2 жыл бұрын
I did the same thing mines a 4x4 though so had to use a stubby filter because of front diff axle but my oil pressure skyrocketed after deleting the oil cooler lines!
@jeffhurst5172 жыл бұрын
What stubby oil filter did you use? I can't seem to find one that would fit. Thanks!
@jeffhurst5172 жыл бұрын
For anyone that needs it, I used a pf454 stubby oil filter. But you don’t actually need a stubby oil filter. It has plenty of room for a full sized pf1218. These are ACDelco part numbers btw.
@forestsoft2 жыл бұрын
what year are these boxes and what models did they come in?
@jrjr65262 жыл бұрын
2000 up vans trucks cars s10 if other then express van needs to run Express van tun as thst is the only l31 engine forr the 411 pcm years
@Chevro916 ай бұрын
00-02 express vans specifically with the 5.7 L31 are the best suited
@stephenmorris81873 жыл бұрын
Been wanting to do that for a while. Seems too easy not to do. Your truck sounds good man.
@dmitrikguajardo60063 жыл бұрын
What ive been trying to figure out is which line goes to the top of radiator. The bottom line from the engine or the top oil cooler line from the engine.
@danametivier27963 жыл бұрын
I am going to do the 0411 swap on my 1997 Silverado L31. where can I get the pinout sheet for it? Any help would be greatly appreciated.
@CoryGP2 жыл бұрын
I got the pinout sheet from Lextech on the gmt400 forums. You have to PM him. He charged me $20.
@adancortes35682 жыл бұрын
@@CoryGP do you know his contact information? so i can pm him about it
@CoryGP2 жыл бұрын
PM him on the GMT400 forums. User name is Lextech.
@Alexisgirl08083 жыл бұрын
Did you plugged the radiator where the lines went?
@billscreations19993 жыл бұрын
No you do not need to
@shootthemoon95493 жыл бұрын
that's not an adjustable wrench it's called an adjustable hammer
@joemercado50713 жыл бұрын
Where are you located, interested in replacing my black box Florida Florida Joe
@wesbennett4703 жыл бұрын
Where did you get the pinout for the 411 conversion? I cant get ahold of lextech to get one
@pantherplatform3 жыл бұрын
I just replaced the black box pcm in a 96 Savana with a cardone reman and it solved the no start due to a cold soak temp reading of 214 according to the computer. It was packed full of aluminum oxide. Looked like cream o wheat in there. Gotta flash the new one now.
@billscreations19993 жыл бұрын
Glad you got it running right.
@erwinalvarado84883 жыл бұрын
What was the bolt part #
@billscreations19993 жыл бұрын
I'll find it
@beardedcatfish70333 жыл бұрын
3951644
@irapena7271 Жыл бұрын
Where did you get ur bolts from?
@simpsonrdlarry4385 Жыл бұрын
Can anyone find their own asshole without someone else telling them? Good god I swear nobody pays attention to a fucking thing anymore!
@jackreynolds53983 жыл бұрын
Do the holes where the lines wete need to be plugged?
@billscreations19993 жыл бұрын
You remove the entire assembly lines and adapter and install what's in the videk
@augustuswilliams12913 жыл бұрын
They won't leak
@MrMrBurnablunt3 жыл бұрын
For someone who has never done anything like this what would you suggest I do to tune and get more power from my 98 c1500 4.3 Manul 5 speed v6.. What runner any suggestions I'm completely new to any of this
@MrMrBurnablunt3 жыл бұрын
Hey brother I have a 98 c1500 and can you help me do my truck to get it tunsd alot beter please I'll pay you brother
@MrRoy-rb1je4 жыл бұрын
Sir, I was told no gasket is needed or required?
@billscreations19993 жыл бұрын
You need the gasket in the video
@bitchard2153 жыл бұрын
@@billscreations1999 guy working that day didnt put the directions in the box.
@sageminentjunky5197 Жыл бұрын
You always need a gasket
@Chevro91 Жыл бұрын
Other videos say the same the gasket is not needed between the engine block and the adapter surface. That gm gasket is out of stock and only place I see is 3 weeks out for shipping
@stevelassetter30722 ай бұрын
Don’t use the gasket!!!
@MrYukon044 жыл бұрын
Why didn't you just tune the black box pcm. Have no issues out of many that I've tuned
@PureMMA4 жыл бұрын
Could you send me a link for a tuner? I've searched everywhere.
@MrYukon044 жыл бұрын
@@PureMMA anyone who can use HP tuners can tune it
@PureMMA4 жыл бұрын
@@MrYukon04 I haven't been able to find a version that supports a 00' 5.7
@MrYukon044 жыл бұрын
@@PureMMA it's not the version. HP tuners covers Chevy from 98 on up on the trucks and 96 up on the cars. All you need is fine a tuner who uses HP tuners. It takes 2 credits for yours
@deerhunter8533 Жыл бұрын
Too expensive to tune compared to the 0411. Plus you can do much more with the tune on the 0411
@BluegabeArrington4 жыл бұрын
WOW! everything has changed, but nothing has changed at all!!!
@THEBRAINANAYTOR4 жыл бұрын
I’m about to do mine. Anything you came across That was difficult? I have all the stuff to do the swap.
@billscreations19994 жыл бұрын
In my opinion it was not to hard. Then again i have been messing with electronics since i was real young.
@THEBRAINANAYTOR4 жыл бұрын
I did mine and it’s running but I can’t do the CKP Relearn.
@billscreations19994 жыл бұрын
@@THEBRAINANAYTOR hmmm what program did you use to get the pcm to work? Hptuners?
@THEBRAINANAYTOR4 жыл бұрын
I bought the pcm based tune from the same guy that gave me the pin out sheet. Pcmpowertunes
@codypiester92563 жыл бұрын
@@THEBRAINANAYTOR hey bud, I have the same ecm and tune from pcmpower tunes. The only thing that has me concerned in the splicing for the trans range switch did you have to do that?
@billbowyer87454 жыл бұрын
Thanks
@billscreations19994 жыл бұрын
No problem. More videos coming soon!
@christouchton57865 жыл бұрын
How did you get a pinout for it I have been trying to find one for my 98 k1500
@billscreations19994 жыл бұрын
check my discussion page on here mate
@billscreations19994 жыл бұрын
Did you ever download it?
@ericnieto93944 жыл бұрын
Would you mind giving me the pin out? I’m having trouble finding it
@MrYukon044 жыл бұрын
@@ericnieto9394 do you have the black PCM? If so just tune it with HP tuners no need to change the pcm
@SafuezLOL Жыл бұрын
@@MrYukon04 I thought the black box couldn’t be tuned with HP?