Randy Astronomy

Пікірлер

@scottbratt9867 8 күн бұрын

Do you have a video on how to setup all of this and configure it? Parts required???

@lblerg 17 күн бұрын

does the metal interact with the GPS? Dont think this is magnetically affected...? Just got this today, going to try it on mine tonight... hoping for clear skies!

@lblerg 16 күн бұрын

Ah reading the instructions says you need to have it far away from metallic objects.

@brucecooper2255 Ай бұрын

That was amazing thank you so much I got a lot of questions like does the 6se track.

@sandaruwanmilan9535 Ай бұрын

Good job... how can connect Pc or tablet cable connection or wifi

@randallfosler Ай бұрын

@@sandaruwanmilan9535 you can use either a cable or a WiFi adapter to connect your NexStar 6/8SE to a computer. A tablet you can use WiFi.

@sandaruwanmilan9535 Ай бұрын

@@randallfosler thank you... is it want celestron wifi adafter ?

@paulscushschofield1288 Ай бұрын

How does the scope know your location?

@randallfosler Ай бұрын

@@paulscushschofield1288 in the hand controller there is a place you can enter your location information.

@paulscushschofield1288 Ай бұрын

@@randallfosler ive been told but cant find it,each time i go into set up the thing goes blank

@randallfosler Ай бұрын

@@paulscushschofield1288be sure you have new batteries installed and the cable is not loose in the plug. If it still does it, your display may be failing on your controller or something else wrong with your controller.

@paulscushschofield1288 Ай бұрын

@@randallfosler ive done all that,even bought the other handset (one with numbers),ive had 3 etx scopes and each one had a fault,from poor display,to uncrehensive jargon on the display to this one that goes blank

@randallfosler Ай бұрын

@@paulscushschofield1288the displays fail in the AutoStar controllers over time as the ribbon cable used to connect the display to the circuit board use printed carbon ink for the contacts. Many are failing now due to the carbon ink deteriorating. I’ve replaced displays in about 10 AutoStar controllers and they then work great. Prior to that the displays either went totally blank or they had garbled characters.

@seniorcordcutter Ай бұрын

Great video, thanks. I need to extend my se8. How did you do it?

@randallfosler Ай бұрын

I do a lot of woodworking so I used a piece of hard oak to make a wood dovetail extension and bolted it to the original dovetail.

@burraaq416 Ай бұрын

How do you remove the tube of etx 80

@randallfosler Ай бұрын

@@burraaq416 I have never removed an ETX60-70-80 OTA. This link may help you. www.weasner.com/etx/techtips/Cooney_70AT_Guide/70atguide.htm

@charlyhernandez355 2 ай бұрын

Hello Nice video, with the wedge now you can track objects better? How much exposure time can you get with the base?

@k.h.1587 2 ай бұрын

A cruel joke, giving a wedge plate for an etx. They can barely handle alt az mode. The optics are pretty killer though

@dw6528 2 ай бұрын

Thank you for doing this! I was contemplating adding a Celestron wedge to my Nexstar AZ for EAA However it becomes apparent that a camera on the back of the OTA would smash into the base for certain positions North facing objects would especially be affected. For example - it would be impossible to center the scope on Polaris. So it appears the wedge would only be usable for observing objects in the southern sky.

@randallfosler 2 ай бұрын

You would need to shift the OTA forward like I did by adding another dovetail. Or you would use a diagonal. I moved on from the wedge and returned it. I found a lightly used AVX mount that works much better for astrophotography.

@dw6528 2 ай бұрын

@@randallfosler Yes Thanks. I do understand that many people transition from a wedge to an GEM mount. As long as one finds the overhead of the GEM mount worth fussing with - it is especially suited for long exposures. Thank you for your kind response. Clear skies and wonderful images! :-]

@GeorgeVarn 2 ай бұрын

Randy, what kind of finderscope is that? Brand, model please.

@randallfosler 2 ай бұрын

It is the Celestron 9X50 illuminated right angle correct image (RACI) finder scope.

@toddschroeder8447 3 ай бұрын

How did you make a cord to bypass the 6 AA batteries and use external source?

@randallfosler 3 ай бұрын

I used a 9-volt battery terminal and wired that to a barrel plug adapter. Below are links to the parts (get the correct size barrel plug adapter for your needs). I can then use my Talentcell rechargeable battery pack. a.co/d/065bVpUy a.co/d/0dkXRzos

@toddschroeder8447 3 ай бұрын

@@randallfosler Thanks for the info. Is your Talentcell pack 12V?

@randallfosler 3 ай бұрын

@@toddschroeder8447yes - I use 12v models.

@ericbarnett6771 3 ай бұрын

Centering Polaris will not provide very accurate alignment, even for visual use. I use the Polar Clock app that shows Polaris relative to polar north. Aligning this way allows for much greater accuracy.

@randallfosler 3 ай бұрын

This does a polar alignment. It does not center on Polaris.

@alexandervukasin6167 3 ай бұрын

Excellent video - Thanks for sharing this.

@AlbertoRodriguezIII 4 ай бұрын

Hi, What equipment are you using from us converters? I would like to do the same thing but I do not know where to start

@randallfosler 4 ай бұрын

I have an older version of this. www.usconverters.com/serial-rs232-wifi-adapter

@jaygee791 4 ай бұрын

Henderson nevada yes

@warlock1663 5 ай бұрын

Hi, thanks for your video. I was wondering if the person that made your sights sells them. I have a 60 and find it pretty hard to try and locate something without them. Thanks.

@randallfosler 5 ай бұрын

I switched to a different way to add a red dot finder to my ETX80. I printed this. www.thingiverse.com/thing:6107685

@leftthigh897 5 ай бұрын

I’m so glad I got to see this with my own telescope, the camera doesn’t do justice to the plasma aches. Excellent video though

@Felldisulfide 5 ай бұрын

Very cool time lapse! How did your guiding work out? I saw your setup video and was thinking of guiding on the Sun as well, but since I was setting up in a field, I didn't think my polar alignment would be anywhere accurate enough for guiding to compensate. CS!

@randallfosler 5 ай бұрын

Guiding worked well. And the PS Align Pro made daytime polar alignment easy.

@KentMcManigal 5 ай бұрын

That’s really cool! Thanks for sharing it.

@janetcraft6339 5 ай бұрын

Thanks

@aprogress2374 5 ай бұрын

Hi, i want to get best result without any vignette on my phone, what eyepiece that can give me zero vignette result?

@randallfosler 5 ай бұрын

Depends on your telescope, phone, and eyepiece. You just have to try different ones to see what works best. I’d start with a 25-26mm eyepiece.

@ma-fi1nu 5 ай бұрын

You don't need the guide camera while shooting the sun.. simply using cpwi or in your hand controller, set tracking mode to solar. Also, you'd be better off using that guide camera in your main scope instead of your phone and lucky image the sun..

@randallfosler 5 ай бұрын

I’m showing how to use a wedge and align the 6SE/8SE in EQ mode in this video. I’m not demonstrating how to use it on the sun. I’m demonstrating it during the day so you can see what I’m doing. I have an entirely different setup for solar observing the eclipse. See my other video for that. I use an AVX mount, guide scope, guide camera, and the PHD2 Solar version that tracks the sun perfectly for hours. Just using CPWI or the controller in solar tracking cannot keep the sun perfectly centered for hours for a long event like an eclipse.

@joelbelden9361 6 ай бұрын

Why is your home position different then what the manual says? Is it different the the ETX125 PE ? THANKS

@randallfosler 6 ай бұрын

Some of the PE models have auto alignment with the Level North Technology (LNT) module. This has a different home position. See my video for ETX Alt-Az Automatic Alignment for that.

@joelbelden9361 6 ай бұрын

No you for the reply. I will check it out.

@egg0408 6 ай бұрын

Very helpful thanks.

@ReubenMRU 6 ай бұрын

Thank you for this, just got one of these babies second hand... can't wait to use it!

@V2KPhotography 6 ай бұрын

Nice setup! Would the guide work during totality when the filters are off?

@randallfosler 6 ай бұрын

No, it has a pause feature. I will pause it for the 3+ minutes of totality and then resume after.

@Cleanentertainment469 6 ай бұрын

Apple only? Can't find it for Android.

@randallfosler 6 ай бұрын

Must be Apple only then.

@oldjedi2001 6 ай бұрын

Excellent video! You've done a great job showing and explaining this process. 👍

@randallfosler 7 ай бұрын

I have not tried it yet on deep space besides Orion. It works pretty well on Orion. Join the AstroShader Facebook group for examples.

@breweroni535 7 ай бұрын

Thanks! That makes sense. A problem I had last night was, after 2-star alignment, I slewed to Jupiter. It got kind of close (I was just testing and my alignment stars were close, scope not leveled). Regardless, I tried the motor controls to point the scope at Jupiter but the controls did nothing. The controls work fine after powering off then back on tho. Any suggestions?

@randallfosler 7 ай бұрын

Try changing the motor speed to a lower speed (like 3) and move the arrows. Then switch it back to a higher speed like 7-9 and see if that helps. I’ve had mine not respond before and changing the speed back and forth seemed to wake it back up.

@breweroni535 7 ай бұрын

@@randallfosler thanks much! I’ll try that.

@vijaygopal101 7 ай бұрын

Hey, Randy, how does the app work on deepsky targets, like m42, m45 or m31, perhaps with tracking, and without?

@ChocotheCat1 3 ай бұрын

I read that the app tracks it and automatically aligns images when it processes it but have not tried it yet due to my area being too f#%k&@g cloudy.

@neupy88 7 ай бұрын

Can I do this with windows? And an old EXT 60?

@randallfosler 7 ай бұрын

SkySafari is not available for Windows but you could look at Starry Night software instead.

@neupy88 7 ай бұрын

@@randallfosler I can live with whatever. But I can't find out if the dongle will work with my ext 60

@PixelPlateauEngineering 7 ай бұрын

Thank you! Nice and to the point. What finderscope are you using?

@randallfosler 7 ай бұрын

That is the Celestron 9 x 50 RACI illuminated finder scope.

@PixelPlateauEngineering 7 ай бұрын

@@randallfosler Thanks for the reply! I'm looking at that same finder. I have trouble bending around to the degree needed to sight along the red dot.

@Nottsboy24 7 ай бұрын

Nice setup 👌 i have the larger 9.25" kzbin.info/www/bejne/e5jaiaSgnd10i7Msi=B-CZ6msYZ2dI31ZF

@orlandobloom9502 7 ай бұрын

🙌🏾👏🏾🙌🏾👏🏾🙌🏾👏🏾😎

@viergarcia 7 ай бұрын

Good straight forward info.

@davidjiannotti1537 7 ай бұрын

Both my etx 125 pe and etx 60 dont seem to have a polar alignment option. My pe is 20 years old and has same tripod you are using. Im so confused.

@randallfosler 7 ай бұрын

You set up the polar alignment option on the AutoStar under the Telescope setting and then choose Mount. It should give you options of Alt-Az or Polar.

@davidjiannotti1537 7 ай бұрын

@@randallfosler Ah! Thank you so much. I kept thinking it should be under setup. Unfortunitly my screen just died again. Waiting on replacement. I have another etx 125 that's going on a nice mount. Picking up where I left off 15 years ago lol.

@daniloduarte8558 7 ай бұрын

I wanna say thanks to you Sir, it helped me a lot. You got yourself a new sub

@randallfosler 7 ай бұрын

Glad you found the video helpful.

@bhastro9959 7 ай бұрын

Very nice basic description of the autoalign procedure with a 6SE on a wedge. However, when i do this, the scope is way off when i choose the first star Sirius. if i then do move the scope to atually point at Sirius, the second star is also way off, and if I align the second star, it says the alignment failed. If I ignore the alignment and just pretend the 2 stars were actually aligned, it says the alignment succeeds - but of course its not actually aligned, and gotos fail. note that the mount is actually well polar-aligned, the arm of the scope is pointing to Polaris, and once I've got the index marks aligned, the scope is at 90 degrees to the arm, as you show in your video. I also accurately entered the date, time and lat/longitude. Last year I was successful in doing the autoalign procedure, although I found it finicky, but this year, with exactly the same equipment, it doesn't work. Any suggestions?

@randallfosler 7 ай бұрын

The things that can mess up your alignment are: - tripod not level - tripod / wedge not pointing north - wedge not set for your latitude - finderscope not aligned with main scope - telescope OTA not balanced - clutches slipping - backlash excessive and setting needs adjusting - weak power source (old batteries). I use a rechargeable Talentcell 12v battery. When centering an object, always finish using the up and right arrow keys. Put the object in the lower left of the eyepiece and then finish moving it up and to the right. This engages the motors for the direction they will use to track.

@viergarcia 7 ай бұрын

For a brief stint not too long ago, my 8SE (no wedge) was constantly failing to align. I use it with the wifi dongle and sky safari. I could not for the life of me figure out what was going on. Going through the hand control settings, I found the time zone and daylight savings settings were all of a sudden wrong. Who knows why. Corrected those two entries and everything’s been working well since. Sounds dumb but double check those on your hand controller.

@brody3431 8 ай бұрын

"Promo SM"

@matiragorri 8 ай бұрын

I bought this telescope -8SE- second hand, waiting for it to arrive to my city. 🎉

@Nottsboy24 7 ай бұрын

I have the 9.25" Celestron Evolution kzbin.info/www/bejne/e5jaiaSgnd10i7Msi=B-CZ6msYZ2dI31ZF

@davidaaaa4611 6 ай бұрын

I have the 8 and the 5 inch. You will love that scope.

Ең жақсы KZbin

Пікірлер