Looks good! Mine is just like yours snd i have been debating on what color wheel to get. Everyone does white and black so i wanted to fo something different. I found a matte bronze wheel that i like and should work. I am going to 20 fir wheel size though with a little fatter tire. As for discount tire. Hopefully you got a new wheel because that's crazy. My local one has great people and they have been helpful in the past but change does happen though

Love how simple you made this you said this part works on Audi a4 b6 and if so could you give me the part number

i bought my 2013 zl1 and had tickle charger wires hooked up to the front and was hidden behind grille curious if prev owner did it right or u gota go from the back ?

Would have liked to see how you separated the wheel trim from the bumper facia. That key moment would have saved me a ton of time. Still a good video, thanks for sharing.

I found rust on my lower door behind the seal. Do u think i would be fine without the seals, especially if it will help to prevent anymore rust or moisture. Might get a little wind noise but i think i might be okay with it

I just cleaned my S4 B7 engine bay with foam and a light spray off and now the vehicle won’t start. When it does, it’s only for a few seconds and then sputters off. Any ideas what to check?

How all did the passenger seat mount to the front? Is the only thing holding it on is the rear nut?

What did you use to re-seal the lens? Where can I buy it?

Hey! I love your channel and think you do some great work. I have a b7 rs4 and have taken the air box out but cannot seem to fit it back in due to the wiggle space and having to attach the horn flap at the lower part of the air box back in to place , I feel I may have to take the bumper and headlight off to allow me some space to do it. Any advice or help would be greatly appreciated! P.S I did all this to change the headlight bulbs ! Merry Christmas

How do you like your x3 now you've had it a while? :-) I'm getting ready to buy a m40i. Love your garage!

I would have had the BMW dealership do it. they respect that ride more than Discount for sure. It might cost a little more. But, techs are trained better. I had the same thing happen to me at Sams on my Audi S5. lesson learned. And, the wheels had just been pulled out of the boxes!

Can you cut the center clamp bolt shorter so it wont hit the bottom cover? I also noticed your side marker lights,,,, there are after market light that are black when off and red and yellow when on that look much better.

Can i get them in Baracuda Silver?

My cruise control is not working (I have audi a4 b6) so if i change this will work ?

could you please post the torque specs

Perfect. That is exactly what I need to do on my 2012.

Would love to see the coding process. Along with a review on how the vehicle tows. Thinking about doing this to our 2022

yo how long in total was this whole process?

Awesome video! I am looking at doing something similar with my 2021 X3MC. Do you have any info or a link to how you got it coded to get rid of the error codes?

Hey man, Maybe its a bit late, but i just want to know how the wrapping foil is reacting with the hot exhaust. Was it melting or was it just fine?

your oil filter funnel should have come with a nail to puncture the oil filter before taking off if not use a screwdriver

Does it pop more or less with the x pipe when letting off the throttle??

What is the product that you sprayed underneath the truck? Couldn't quite catch the name - Thanks

Thanks for the life story before not showing the garage floor painting. Off to the next video.

What locations did you end up connecting the pump motor wired to in the box?

Simple and to the point. Thanks man.

they should have charged most of that to the recall bill!

How you like it? Tows good? Kid friendly? Thanks bro!!

Did they just strip out the cam washers? I'm afraid the same happened to my truck as they don't hold tight and I get a clunk when turning

That’s what I want.. longer power band. 2011 2SS manual, Completely stock it only starts around 3K. The clip of y’all driving has me sold on long tubes.

SO you have a California vehicle. Question. In the eventuality that you have to change the cats (not sure if you have done it already) do you need to use the California legal cats or the cats that are sold in Michigan?

I can't believe how squiggly and inefficient the stock exhaust tubing is. Holy moly Rocky. I guess I'll have to not just get the long tube headers when I get my C7 Grand Sport in about a year, but the X-pipe as well...

I did not watch the whole thing! How could you make this suck so much?

I like the stance....it's too bad though, if you guys did the work that you didn't share that on the video too.

Love your channel

You have my dream garage I already got the zl1 now time to get the z06 two favorite cars

whats the depth of your concrete

I know this is old but the next thing should have been the crash bar.

Too much I Think, I guess and might!!! Other than that it’s okay.

No sound

Con sole. Not counsole

Had a similar issue with Discount tire here in the DFW area of Texas. Scratched my new gloss black powder coated VOSSEN wheels while wrapping them in Michelin 4s tires. They PAID for their ERROR! And every visit since then the MANAGER does my instal while I watch him like a f@cking HAWK! Sad it has to be like that…

I was questioning if I really want the x3 m cause I wanted to put a receiver as well. Now I will have to wait for the 2023 model but plan on doing the same to mines. Keep up the videos and mods, your x3 m looks great

Great video, I need to do the same to my Harley SGS. can you list where you bought the equipment or put a link above?

Some specs: This kit: Fronts: 370x30mm, four pistons Rear: 345x24mm, dual pistons On an F-Series, this kit requires 18” wheels or larger. Sportline (Stock brakes): Fronts: 340x30mm, quad pistons Rear: 330x20mm, single piston floating Other F-series cars, without Sportline, came with single piston calipers front and rear. The four-piston gray Sportline calipers are NOT the same as the calipers in this kit! While both are 4-piston, 40mm pistons, the stock caliper can only fit a 340mm rotor and the rotors in this kit fit a 370 or 380mm rotor. So be very careful if you buy these used! This kit will not improve “stopping power,” at least, not in front. Contact area is 100% the same in front. Only difference you’ll feel is the changed brake pad material. What is different is that the 370mm rotor dissipates heat better, so brakes won’t overheat in track and high performance driving.

What voltage 110 or 220

I heard they are only good for 10-15 washes 😬

pretty raptor, i have a f150 platinum with oil pan plastic, where can i get a metal one.

Torque Specs: Bleed bolts: 9mm screw: 5-8 ft-lbs 11mm screw: 9-13 ft-lbs Lug nuts: 103 ft-lbs Caliper to pad carrier: 21 ft-lbs Brake hose to caliper: 18 ft-lbs Brake hose to steel line: 12.5 ft-lbs Front pad carrier to steering knuckle: 81 ft-lbs Rear pad carrier to wheel bearing carrier: 22 ft-lbs plus additional 90 degrees Rotor to hub screw: (Replace Screw) 16nm/12 ft-lbs

Nice truck!