Bad ignition coil, had that happen to a neighbor's 270. I thought it was running lean at first but in the end it needed a new coil.

Use a flywheel puller

That’s great for the environment

What is the model of this grass cutter when buying spare parts? Thank you. 😊

Kendala apax kalau semprot minyak di foring

Cari blok dan seker nya MS 380 kok susah banget mas, kira2 bisa gak gak di ganti dengan produk yang laen

Where from purchase this tool online

Adjust the wind/air screw

I was looking up so much stuff but I just need one thing thing thank you

hello! I've had one of these a few years now and had no idea what it was. Do you have another gas tank for one of these?

Hala espero que este bien nesesito filtro de aire dela 08 el que va rn la cola

Как будто на её масло лили специально цепь смазывали вручную 😂😂😂

Bang bisa nanya

Mayron pa bos

Wow, looks good. What filler material did you use and did it last ? When i see you brazing it, it looks easy but you're not a beginner. Really went through to the other side.

Oil kantol kesi kate plz sekado

👎

Why does my machine heat up for about ten minutes?   Feedback

Sthil tipe apa ini bang

कमेंट किया है आपको वेलकम भाई

पिस्टन कितने काआता है रेट बताओ

May pa ayu Nako Ako buldoser

Please install sprocket

Nice

Hi, this has a splash system? So how does oil get up to the tappet area? Same splash? No pumps on these type? I got a 24cc Yardking trimmer and it makes no smoke or smell BUT seems to use a tablespoon of oil every 30mins?? i have to keep topping up little 70mm sump. There is plenty of air coming out of breather and spits a bit there too. Thinking somehow the piston ring might be stuck or worn bore area from last user might have run it dry of oil ect. Rockers go up and down a lot so cam might be ok. Watched you video just as prep to pull apart.

Very sturdy saw. Heavy yes, but heavy duty. The fact that this saw is still in operation says a great deal about its design and construction. I know of no modern saw that is built of this same quality.

Setil 070 kah

Please keep your fingers and your life. Do not holx on to the bearing of a 1000s motor with two fingers when spinning it. Do unplug the machine when repairing. Touching open contacts can kill you. Or start fires. Also are you greasing the break?

I started my saw up once and it ran in reverse and spun the clutch off the spindle. I didn’t have the cover on and everything went flying. I found the clutch drum and the washers and that was it. One thing though, that saw was running crazy fast.

Hello

Paano ung naka suka ng gasoline

7:50 What the name of that star wheel and what Israeli do??

What did you use to do this i have a whole in the bottom of my N62 engine?

Self confidence 🎉🎉

No safety ...

rings position bhi clear kar den bro

💪💪👍👍👍

هذا المنشار ستيل الماني نوعيه ممتازه

👌👌👌👌👌👌👌

Teşekkür ederim kardeşim. Sorunu başarıyla çözdün. Teşekkürler

Between mini chain saw which company is professional

ভাইয়া আমি একটা কিনতে চাই কিভাবে কিনবো

Apakah harus di ganti jika goyang nya seperti itu kx

Usually fuel Been left stood oil and petrol mixture not right Empty put new give good shake. I always let my petrol strimmer run out empty carb. See the difference

ما اسم تلك العجلة التي تتحرك عندما تكون حرة المنشار النزين مرتفعة فقط؟

🤣🤣🤣

Very nice

Buenas El mecánico se lleva bien,, con ese maquinon Saludos

May malapit ba na shop dito project 8 quezon, pagawa ko sana chainsaw ko

What about replacing 090 to 070