Thnx man. I hope KZbin will see your kind words!

@@aspeed3dtoys thx

Thank you so much for your support! It means a lot to me. I'll keep working hard to create content you enjoy! 🙂

@@aspeed3dtoys thx and u have a amazing content

Hi. Unfortunately I never scale model I followed the recommended print settings from this link www.printables.com/model/593185-dummy-13-printable-jointed-figure-beta-files where (100% scale, 0.4mm nozzle) Material: Frame parts - ABS, ASA, or PETG (I printed frame in PLA.) Armor parts - Any Layer height: First layer - 0.2 mm Other layers - 0.15 mm Infill - 20% rectilinear First layer speed - 25% of default Elephant foot compensation - 0.15 mm Supports - None Brim - 5mm The naming obviously depends on the slicer.

Hi I followed the recommended print settings from this link www.printables.com/model/593185-dummy-13-printable-jointed-figure-beta-files where (100% scale, 0.4mm nozzle) Material: Frame parts - ABS, ASA, or PETG (I printed frame in PLA.) Armor parts - Any Layer height: First layer - 0.2 mm Other layers - 0.15 mm Infill - 20% rectilinear First layer speed - 25% of default Elephant foot compensation - 0.15 mm Supports - None Brim - 5mm The naming obviously depends on the slicer.

Olá, que bom que gostou! 😊 Eu não vendo nada, apenas gosto de imprimir algumas coisas em 3D por diversão. Muito obrigado pelo seu interesse!

That's right. It's better to print the frame in PETG or ABS.

Can i hav t13

Thank you so much for your kind words! I'm glad you enjoyed the video. The figure I 3d printed didn’t cost too much-just a couple of bucks for the filament and electricity. The real fun was in putting it together! 😄 Thanks again for your support, I appreciate it!

Hi I followed the recommended print settings from this link www.printables.com/model/593185-dummy-13-printable-jointed-figure-beta-files where (100% scale, 0.4mm nozzle) Material: Frame parts - ABS, ASA, or PETG (I printed frame in PLA.) Armor parts - Any Layer height: First layer - 0.2 mm Other layers - 0.15 mm Infill - 20% rectilinear First layer speed - 25% of default Elephant foot compensation - 0.15 mm Supports - None Brim - 5mm The naming obviously depends on the slicer.

@@aspeed3dtoys TY C: it rlly helps :D

Hi there! I use a Bambu A1 3D printer with a 0.2 mm nozzle and 0.1 mm layer height. For your Ender 3, try using the same nozzle and layer height and slow down your print speed to 40-60 mm/s. I hope it will work

@@aspeed3dtoys thanks por the advice I'll definitely try it. I just subbed

@@aspeed3dtoys hi it's me again just wondering the nozzle that comes with the ender 3 is a 4mm right I might be wrong but if not what is the layer height for it?

@@averynielson-is9km Hi there! The Ender 3 default size nozzle is 0.4mm. However, it also supports other sizes like 0.2mm. For a 0.4mm nozzle as advised by Dummy's 13 creator: a First layer 0.2 mm Other layers 0.15 mm you can find Recommended print settings here: www.printables.com/model/593185-dummy-13-printable-jointed-figure-beta-files I Hope it will help

​@@aspeed3dtoysI tried it and it was worse I used the same settings you suggested and the limbs don't fit together they are too big should I size it up?

Hi 🙂

sure 🙂

Yaaaaaaaaaaay❤❤❤❤❤😊😊😊😊😊😊😄😄😄😄😄😄😄😄😄😄

Hi there 😃

Dragon ball. Totally agree with you! 😊

Thanks and welcome

@@aspeed3dtoys you’re welcome

Thanks for the sub!