I have an XJ-S with this ECU and I'm just about at the point of throwing it out. I have been through and tested the diodes, replaced many of the capacitors and some of the resistors, reflowed a bunch of solder joints and even rewound the inductor thingy to no avail. The ECU still outputs shortened or missing pulses to the ignition module when the revs get too high. I've measured this on a scope, and verified that the inputs to the ECU seem OK. With the ECU in this state. I can cruise around OK, but if I floor it, it's like I hit a rev limiter. The exhaust pops and bangs, the rev counter goes nuts and I have no power.

hello in the output cable there is R-g1, G-g1 and B-g1 and in the cathode ray tube there is only 01 g1 how am I going to connect the 03 wires

Cool video! I've done a belt change on my CLD-1450 (much older player) and I'm struggling to get the tray back in! I'm glad I wasn't the only one finding it a challenge! I've had 2-3 attempts and I came back to this video to have another look. Looks like that spring screw on the side when you are just loading the tray in is my next trick to try. I can reach the tray gears from the front door like you're doing. I've rage quit for now so I'll try again another day :)

hello I have a bk 467 crt tested the ammeter does not read the filament voltage it only indicates 1.5 v. but when I measure on the wires of the output cable I find all the heating voltages

It sounds like a satisfying repair journey! The B&O 8902 is a beautiful piece, and diagnosing the extreme red flare over composite must have been quite the puzzle. Identifying and replacing those faulty Philips light blue caps with new ones was a smart move, and it’s great to hear the composite picture is now much improved. Keeping vintage equipment like this in top shape takes skill and patience-well done on bringing this classic back to life!

I have one boxed with a manual in working order if anyone wants to buy it.

in reality the glue that was dry was used to show you how the detached part was originally attached to the magnet because it was phased by the manufacturer, by sanding it you removed the signs that made you understand in which position it should be attached to the magnet and it will never turn the right way again, the same thing happened to me and then I discovered that it had to be done as I told you and I had to buy a new motor

How do you get the front wipers out of service mode? Mine are stuck in the upright position after changing

Vhs tapes keeps me moving more than my Disney plus does i got rid of my Disney plus because of my health I was getting more lazy on Disney plus my vhs tapes keeps me moving more and more healthy than my Disney plus and my Netflix i got rid of it only kept my vhs tapes nothing else

Thank you very much.. i save my Sony C7 from 1984 with your video U tube. Taking care ....merry Christmas and happy new Year.

Does anybody know if this would work on a smart tv or would I have to find a crt tv ?

I'vs never found a way to make this work with scart?

A crows foot spanner on an extension bar would have worked on that bolt.

what NAS was you using at the time for it to connect to your riscPC?

Everything proven vhs tapes cleaning tapes VCR belts off eBay and Amazon now days

Опель Астра машина топ

Pre-1990 releases on VHS and Betamax copies have its original soundtrack unlike any DVD and Blu-ray releases that featured an altered soundtrack (few dialogue changes, instrumental synth songs, modern SFX). It’s like if whoever was in charge of the remastering process back in the DVD days had tried to make it sound like a Fast & Furious movie or if George Lucas came in but instead of changing the original Star Wars trilogy to integrate CGI in there where it hadn’t existed in their motion pictures, it’s with the audio. It was ridiculous. To put it in a certain scenario, if someone were to go into an art museum and replace the real Mona Lisa painting with a replica, it’s a case of destroying history to which I never appreciate.

Great video , I’m assuming this would work using a dvr recorder to . As I still have my dvr with HDD I used to record sky tv when you used to be able through scart 10 yrs ago .

If it has SCART output there is a good chance it will properly convert to ITU-R REC.470 signal. Though I would still prever to make a master file and then duplicate from that.

I cannot believe i just lucked up on one of these in superb condition for only $100. It doesn’t seem to like any other tape but the Panasonic SP tape that was inside it. Very strange. I’ve tried using a new VHS tape but no joy.

Such nice machines! I have an Akai VS-9500 which is based off the JVC HR-3320 (some sources say 3330 but the 3330 has more functions than the VS-9500). I changed the belts which was easier than I thought and have to replace the cassette lamp. Only the belts at the top side are a bit of a pain because of the cassette lift. I'm having a bit of a struggle getting the lift back in correctly. The gold part that sits at the back of the circuit board for ff/rw/play etc looks different in my machine. Also the previous owner said that the machine ate tapes, so I'll have to check on that as well.

This is a great way to bypass Macrovision copy protection on DVDs and VHS tapes. However I use a PC and VLC media player to record in widescreen.

I don’t have enough cables to test but i wonder if a raspberry pi with HDMI hat can capture netflix

Hi mate I did a similar video

I'm starting to wonder if KZbin has learned to read minds. Yesterday I set up a VHS recorder for the first time in 25 years and I was wondering about this exact topic. And now your video popped up into my feed. Remarkable. Nice channel, by the way. I have subscribed.

Hi, do you still have these?

Thanks for info 😃

Thank for your advice - this video was a massive help for me today 🙏🏼

Since NO ONE is doing this anymore there is absolutely no need for vhs copy protection ^^ But it´s a really cool idea, especially for Stranger Things.

Thank you. Was struggling to swap the rollers over on the DSC85W and could not see how to move the drum out of the way. Now successfully done. 👍

Legend. Just picked up one of these at a market this morning for AU$30 and it had the exact same motor noise. Same fix. Is SILENT now. Thanks for sharing. Wouldn't have had a clue without this to guide me.

Assuming there has been no leakage, then will this still work with the same efficiency as originally built? I wonder if newer ones would be more energy efficient.

IV done most sensors and it still runs rich till the point when it gets to temperature the car has literally no go and will cut out and Is not drivable and has been for a year highly frustrated

Good video I just wished your fingers weren’t blocked by the back of your hand

Good video I just wished your fingers weren’t blocked by the back of your hand

Great video. Thanks. Clear explanations, clear speech (which is rare these days!). Quick Q: If you're winding back the caliper piston to replace the pads, do you have a simple tip to ensure its lined up with the pins behind the pads?

Very interesting. I'm wondering, would this be able to record off of a Roku TV? If so,how 🤷?

Can someone just make a in-depth video of how to do this!!! Omg! I’m so freaking angery I’ve tried everything to make mine work and it’s crap! It’s not working no picture I put over 200$ into crap to do this and nothing works!

I have this model of dryer, does anyone have a part number for the wheel as I can't seem to find one?

I know what its like though as you said no a fix all but it is a lifesaver i love the video as i can relate so much

I have a used copy 1984 edition on VHS still working to this day. Tried to find The Junkman but it’s a rare sequel on VHS, same as Deadline Auto Theft. These are all fun movies to watch and never get old, good vibes☮️🩷🪩

I had a Sharp GF1740 when I was younger and just called it a Radio Cassette (as it was mono), can't say if I've ever called these either Boomboxes or G'Blasters. Something like this I'd call a Stereo Radio Cassette. According to Google the term Boombox was first used by the New York Times in 1981, so maybe it was more an American term that eventually made it over to the UK.

Interesting video, unfortunatly there are so many adverts popping up I couldn't continue watching past the first 15 mins. Absolute shame.

Hi I have a tv similar to that but it's purple on the tube

I bought one in 96 or later and it was wood. I still have it, but I have not used it in 20 years. I switched it on yesterday and it was not working. The red light showed. I wiggled the float thing and it made no difference. Do you think these have any value these days for spares or repair? It seems such a shame to toss it.

Very interesting and enjoyable James.I admire your tenacity.Look forward to the next Video

i hate my breaks. and my hvac. and my...

I had problems with my washing machine for 2 weeks, this vid saved me from expensive maintenance fees. Thank you!

I changed lacing belt and the eject is flashing after putting everything back together.

Thank you. This greatly helped me replace the rollers on my Beko DCU8230. However, I did not remove the heater or any electric cables at all. That was overkill for me. @19:46, all you need is to remove the bottom 4 screws that go into the chasis. + two top corners. This will help you push the drum back about a 1-2cm or so. That's all is needed to remove the existing rollers and put a new one in!