Thank you for the video, I'm new to laser, never thought it is possible to make a bag with wood!! Could you share your setting or even the design file?
@TheFrogOnAlog3 ай бұрын
Since I’m using a thin, 2.7mm, plywood it cuts and bends easily. I got the LX1 with 20w module, updated firmware and used 100,72,1 when cutting this bag. I bought the design at Etsy and scaled it to fit my material. Etsy, laser cut wooden bag clutch
@Mrchiholi3 ай бұрын
@@TheFrogOnAlog Thanks for sharing, will definitely give it a try!! Just got a LP4 and have been watching KZbin video to learn how to use it, thank you again for helping!!
@bombardus22584 ай бұрын
Great..... How about some settings?
@TheFrogOnAlog4 ай бұрын
LP4 1064nm. High 4k for black, low 2k for different shades of brown. 4k, 100, 50, 1 2k, 1-5, 1-5, 1
@Granx294 ай бұрын
this is done with the 1064nm fiber laser correct?
@TheFrogOnAlog4 ай бұрын
No, I’m using 450nm on glass.
@Granx294 ай бұрын
@@TheFrogOnAlog interesting.... I will give that a try then... haven't had any luck painting black tempera on amber beer bottles and using 1064nm to etch...
@rahh86836 ай бұрын
Hi Where do you get the number 65.20 diameter from? I have the same tumbler and it gives me 25.50 diameter
@TheFrogOnAlog6 ай бұрын
Might be due to that 65,2 mm equals 2.55 inches. I measured the mug earlier, to 65.2 mm, with a caliper. Since I did a test round before, the value remained in that field.
@hooksntoggles8 ай бұрын
So many questions, but I have only found this video. First question, what are the clips you used on your LP4 to hang the protective shield panel and where can I get them, please?
@T1merlane8 ай бұрын
Wow, wonderful job - they look very nice👍
@dzopsi9 ай бұрын
Too complicated
@FredTyco9 ай бұрын
Hi Frog :) Do you like your LaserPecker LX1? Will you buy it again after using it? In "official" video there's mistake and default on engravure... so I'm not sure which one to buy (looking for xtool and LaserPecker LX1)
@TheFrogOnAlog9 ай бұрын
Hi. Yes, I’m quite satisfied with the hardware but the app is still a bit immature. My impression is that most problems occur when creating designs in the app but since I manage all graphic in Illustrator I’m not affected by that. I test everything; graphic, material, settings, orientation, rotation, before going live so I’m very rarely negative surprises by the outcome. I’ve no experience of other lasers then LP.
@schmots10 ай бұрын
Do you just use design space? I want to use light burn with my lx1 max. But it always freezes up during jobs if I do.
@kazea215810 ай бұрын
what's the power and depth you were using?
@cynthiasymons10 ай бұрын
I suspect that a lot of us who just got our LP 4 (and like me-new to lasers-are out looking for videos like yours. Thank you for recording. Please give us more in your description, or just ask through what you are doing. There is not a lot of info out there yet, and videos like yours could really help!
@TheFrogOnAlog10 ай бұрын
Hi. Yes, some of these videos are quite brief. I link them into the lp4 fb group where you will find more info.
@cynthiasymons10 ай бұрын
@@TheFrogOnAlog Thanks! I am in one of those groups…I will look.
@Austeration10 ай бұрын
That's very cool, so did the laser actually etch the glass or did you have to put something on the glass ?
@TheFrogOnAlog10 ай бұрын
Thanks. It’s a permanent white etching.
@Austeration10 ай бұрын
@@TheFrogOnAlog yes yes but did the laser etch it or did you have to use etching cream or paste ?
@TheFrogOnAlog10 ай бұрын
The laser etches it. @@Austeration
@shermi644 ай бұрын
Hello what did you use for black paint please
@Mr.Stoobz11 ай бұрын
Well done. New LP4 owner here, I appreciate the tips. Happy engraving, friend!
@MaartenVanEynde11 ай бұрын
Nice! What is the spray you use?
@TheFrogOnAlog11 ай бұрын
Black Tempera. A water based paint aimed for kids. I’m using a paint gun but airbrush or foam brush also works well.