6:50 Nie bałeś się tego odkręcać tylko na tym cienkim pinie w zamachu?
@jakubfox532922 сағат бұрын
How the hell do you even remove the bolt on the bottom, wtf, i cant fit anything in there
@SlawekSzumski2 күн бұрын
Mam ten sam problem z n42. Wymiana czujnikow nic nie dała. Czy normalne jest ze błędy da się kasować na odpietych wtyczkach od czujnika?
@c.h.u.d2 күн бұрын
What a pain in the nuts couldn't they have made valve seals last a whole lot longer
@traqnsavov8223 күн бұрын
this blower protects the catalytic converter , from the rich mixture of cold run and removing it is the dumbest thing I've ever seen
@roxannebacani10 күн бұрын
Hi boss saan po makakabili ng ganyang valve seal
@joaquin911312 күн бұрын
Hi friend, good video, can you tell me where you buy the spare parts?, thanks for all.
@teodorstan781117 күн бұрын
Why is coming out any dirt from the radiator?
@user-xe9ty1sm2q17 күн бұрын
for which sundresses did you use a torque wrench and what tightening force?
@ziemowitlewandowski17 күн бұрын
Jak ja widzę te wszystkie testy influencerów którzy sprzedadzą się za każdy bonus to po prostu ręce opadają
@ChristopherAalto18 күн бұрын
we have the same car bro lets I'm interested in what you doing here :) maybe some retrofits? :)
@itachirb265418 күн бұрын
Hi bro where did you get the tool? And the n42b20 engine is a ohv or ohc type ?
@elvernamcdonald338819 күн бұрын
Hi, thanks for the video, well presented. My car do not want to start, I accidentally started my car in second gear. My battery is new, everything on the dashbaord goes on, but when I turn the key nothing no sound. Any advise?
@pandymitr239020 күн бұрын
Podpowiesz czy pin powinien blokować wał w GMP na pierwszym cylindrze w N45? Ułożenie krzywek po zamontowaniu blokad na wałkach by na to wskazywało. Walczę od kilku dni z rozrządem i jestem blisko podpalenia tego gruza... W samochodzie przeskoczył rozrząd i przestał zapalać, na starym rozrządzie mierzyłem kompresję i było 9, 9, 11 i 11,5. Po wymianie na każdym jest praktycznie 0 i tak na oko pin wchodzi w koło zamachowe około 60 stopni za GMP pierwszego cylindra. Będę mega wdzięczny za każdą podpowiedź ;)
@kinimod520 күн бұрын
How many valves has this engine?
@dominichernandez808727 күн бұрын
Hi, I want to change the timing chain and guides in my N46 engine (just preventive) it has 101.000 km. Is it really necessary to drop the oil pan? Timing guide is not broken. What precautions should I take to make sure I don't move the balancing shafts? Thx
@CheStephens27 күн бұрын
Did this fix your issue with the car, i have a VE commodore 2007 model utility, it came up with a p0717 code this car also has the GM 5l40e transmission im just wondering if you would recommend replacing sensors like you have.
@Maks-e3tАй бұрын
Ile wyszło za wszystko
@-xescobarx-1758Ай бұрын
How much lower is the car with the springs 25mm or 40mm?
@wilasbmxnyc8719Ай бұрын
jakie są widełki remontu silnika m52b28 ?
@TylerMartin-bf9ybАй бұрын
Thanks for the video I figure the pump was where and operated where it was. I work on American vehicles. But for the power steering pump pulley his it with a rubber mallet at the very least. If you don’t have one use a rag as a dampener
@gro9noАй бұрын
Dobre z was świry, jakby wszystkie recenzje narzędzi tak wyglądały świat były piękniejszy 🤣🤣🤣
@dabr0vsky298Ай бұрын
Halo halo, bardzo proszę by kanał wrócił do żywych. Chcemy oglądać filmy z prac nad Jettą i Golfem. Pozdro :D
@russka_faja5042Ай бұрын
Cześć czy przy wymianie zacisków przód zostawiłeś seryjną pompkę hamulca jeśli tak to czy pedał hamulca nie był miękki?
@korneliuszbajda2588Ай бұрын
Jedna rzecz mnie wkurwia w tym silniku n42b20a dbam rozrzad zmieniony olej na czas wszystko co mozliwe co porobione a jak kupilem pracowal cichutko po kilku latach klepie jak diesel
@TheAlfaDriveАй бұрын
Hey currently rebuilding the same engine for my e36 coupe if you have a workshop manual i couldn´t find any on google cheers
@malwa82522 ай бұрын
A ten napinacz z blokad ile wkrecić ????
@gorillaprojectcar2 ай бұрын
Nie pamiętam dokładnie. 50-60nm
@przemysawsek49742 ай бұрын
Witam. Ile u ciebie taka naprawa kosztuje? Jestem zainteresowany.
@danksquad9032 ай бұрын
How did you tighten The crank bolt, when it spind freely, did you lock The flywheel?
@Chyloku2 ай бұрын
Super film
@fredrikforthun6032 ай бұрын
What did you do to lock the cam and crank?
@DavidB-rx3km2 ай бұрын
Why can't these videos just be instructional without trying to be stylish with banging tunes and camera editing.
@gorillaprojectcar2 ай бұрын
Because noone would watch them 🤷♂️
@Volfran2 ай бұрын
Witam, pamięta pan z jakim momentem dokręcić napinacz?
@gorillaprojectcar2 ай бұрын
50-60nm jakoś, nie pamiętam dokładnie
@blardymunggas68842 ай бұрын
I hate old BMW. Never ending repairs. Just not worth it
@user-by2mp4tk9q2 ай бұрын
شكرن للمعلومه ❤❤❤احبك ❤❤🎉🎉🎉🎉
@miki-bn8jn2 ай бұрын
Witam jakie uszczelniacze zaworowe kupić febiego czy jakieś inne sprawdzone
@piod92692 ай бұрын
Można takiego vanosa regenerować czy tylko wymiana?
@Raccoonsareawesome2 ай бұрын
Unless you did use rtv silicone between the top and bottom time chain cover, it will most likely start to leak over time at the rubber that separate the two covers.
@kamil80792 ай бұрын
a uszkodzona pompa wody może wydawać dzwięki przy 2 tyś obrotów ?
@RealBadPing2 ай бұрын
Hello! I can’t find Top dead center. I removed the little panel protecting the flywheel. I can see the hole when rotating the crank. I can’t get the pin into the hole. Please help.. i only have a few days left to do this job..
@agr3sivepl5833 ай бұрын
dawaj kolejny film z składania
@gorillaprojectcar2 ай бұрын
Oj chciałbym to trochę pchnąć do przodu. Obecnie robimy wylewkę w stodole stąd przerwa w filmach 😉 i trochę napraw dla klientów
@oktawiuszmarczykowski41403 ай бұрын
A jaki olej najlepiej lac do tego silnika? Obecnie leję Millers performance c3 5w30
@gorillaprojectcar2 ай бұрын
Byle nie najtańszy i żeby spełnił normy LL01 minimum a najlepiej LL04 😉
@oktawiuszmarczykowski41402 ай бұрын
Bardziej się zastanawiałem czy lepiej 5w40 czy 5w30 a może jeszcze inny. Akurat obecny co leję ma LL04
@oktawiuszmarczykowski41402 ай бұрын
@@gorillaprojectcara jeszcze mam pytanie czy jest bezpieczne odkręcanie koła pasowego z zablokowanym kołem zamachowym?
@belos653 ай бұрын
Hello! Thanks! too good Video. You say that you need to change the timing chain and timing chain tensioner after 150,000 km. Bmw tells me I never need to replace any of this. They say it lasts the entire life of the car. My daughter lost a lot of money because her Bmw 318i N43 Year model 2009, the timing chain skipped a couple of teeth. And the valves hit the piston on 2 out of 4 cylinders, when her Bmw had gone 245000 km. Thanks! from Tommy Bertilsson from Sweden
@gorillaprojectcar3 ай бұрын
The average lifespan of this chain and guides is 150kkm in my opinion. I know bmw says something else but the chain tends to stretch and it hits plastic guides pretty hard then they crack, block oil feed and you have a catastrophic failure… preventive maintenance is the best way to go. I’ve seen original 260kkm timings but only once. All depends on how the car is used. The M series engines had a lot better chains and guides. Those were able to handle lifetime of the car. Cheers 🍻
@dabr0vsky2983 ай бұрын
Ajajaj piękna sprawa, bardzo proszę o film z prac jak najszybciej. Pozdro :D
@gorillaprojectcar3 ай бұрын
Ostatnio tak mało czasu ze ta jetta to jeszcze z miesiąc będzie robiona… chciałem cokolwiek wrzucić żeby nie było że zapomniałem o kanale 🤣
@Sp3NgL3R_MF3 ай бұрын
Hello, where i can find specifications of crankshaft for my E46 316i ?
@gorillaprojectcar3 ай бұрын
If you mean the dimensions then honestly I don’t know. I don’t have a machine to do anything about crank so I didn’t even look 🤷♂️
@janmagalso3 ай бұрын
You help me a lot good sir 😊
@gorillaprojectcar3 ай бұрын
Glad to hear it 🫡
@christopherbanda65243 ай бұрын
You are just an amazing tutor thanks for your unwavering efforts of giving out information. Keep it up.
@gorillaprojectcar3 ай бұрын
Thanks a lot 🙌 it means a lot 🫡
@Re1nTs3 ай бұрын
hey! i changed chain and rails,but car still wont start. In live data,ex vanos sensor is not working, but sensor is good. any ideas? bad ecu?
@gorillaprojectcar3 ай бұрын
Issues like that are difficult to diagnose from afar. I’d check crank sensor and double check the timing 😉
@Re1nTs3 ай бұрын
@@gorillaprojectcar yes,true. I will test compression too. But in live data ex camshaft sensor is not working,when cranking engine. Sensor is working,connector was full of oil.. problaly bad wiring or ecu. The old chain and rails were good,but changed anyway to avoid problems.
@rafatargaszewki30763 ай бұрын
Posiadam ten silnik u siebie od 2 lat i fakt jak robisz wszystko na czas i dobry olej to podstawa , to faktycznie silnik przyjemny w użytkowaniu aktalulanie 282tys km
@gorillaprojectcar3 ай бұрын
Mój nowy nabytek w tej chwili 332 tysięcy i dosyć sporo na gazie zrobione. Śmiga 😎
@flotsam63833 ай бұрын
I just came across your channel great material. I am in US but just visited Poland. What part of Poland are you from? I have a 95 325i . I need to follow you.
@gorillaprojectcar3 ай бұрын
Im from Silesia near Częstochowa. I moved to a village house last year 😁 now I have my own barn that is another money pit for me 🤣 hope you enjoyed your time in Poland 😎
@flotsam63832 ай бұрын
@@gorillaprojectcar i did we went to Warsaw, Kracow & Zakopane. It was great at Zakopane, went to Kasprowy cable car. Keep up the great work