Жыл бұрын
2 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
Пікірлер
@RoadRoyals Ай бұрын
how do you blend the welds so well without burning through? great work
@Project_Pat Ай бұрын
@@RoadRoyals I use my air powered angle grinder with 3M 2inch discs. Usually 80 grit. Gets the welds down quick, and is easy to handle while being precise. Trust me, I’ve burned through a few times.
@broncoramfan 2 ай бұрын
Did you thin your paint?
@Project_Pat 2 ай бұрын
Sure did. 👍
@Project_Pat 2 ай бұрын
This is primer though. Still haven’t actually painted it
@arduinoNube 2 ай бұрын
Mine has lots of overspray like yours. I had to turn the pressure way down (lower than the clean setting).
@Project_Pat 2 ай бұрын
I’ll have to remember this when I finally get around to finishing it. Appreciate the tip!
@Sikken83 4 ай бұрын
Shes gonna outlast you now. I love the build.
@Project_Pat 4 ай бұрын
@@Sikken83 Thank you…I’m hoping for the first start this winter. Fingers crossed.
@Noah-se7mn 5 ай бұрын
yessir 💯💯
@Project_Pat 5 ай бұрын
@@Noah-se7mn Thanks!
@Michael-yi4mc 5 ай бұрын
Is that a size 515 nozzle?
@Project_Pat 5 ай бұрын
@@Michael-yi4mc I’m pretty sure that was the tip I used.
@BiggHoss 6 ай бұрын
When sanding a panel to remove clear coat always use a DA sander with a foam pad. using a hard pad like that can leave waves
@Project_Pat 6 ай бұрын
@@BiggHoss Appreciate the advice and information!!
@BiggHoss 6 ай бұрын
@@Project_Pat Painting is all about prep. 80 to 90%. kzbin.info/www/bejne/oKqznp6hjNiWY7s this is a pretty good video that teaches good sanding techniques. Good luck with the restoration. At the end of the day all the experts can nit pick but as long as you're happy with a job for your truck, that's all that matters at the end of the day.
@themechanicman3865 6 ай бұрын
Try doing it where the whole rocker is Rusty into the floorboard you just did the outer shell when you got to cut the hole rocker out of another truck clean and you just can't cap it and put a new shell on it that's what really takes to see how good you are
@Project_Pat 6 ай бұрын
@@themechanicman3865 I was going to try that with the original cab that was completely shot. Then I smartened up and bought this whole parts truck for 1K. Power everything. Saved a ton of time and money. But I’m sure you’re having a lot of fun telling everyone how you saved a completely shitty cab.
@billybobscat6233 6 ай бұрын
Absolutely amazing work!
@Project_Pat 6 ай бұрын
@@billybobscat6233 Thanks….Very happy with the results for my first time doing this stuff.
@slightlycynical 7 ай бұрын
Nice reseal kit
@Project_Pat 7 ай бұрын
🤣🤣🤣
@steelewheels1365 7 ай бұрын
Mine doesn't work that good. Did you change anything and can you take the handle off?
@Project_Pat 7 ай бұрын
@@steelewheels1365 I didn’t change anything. What’s going on with yours?
@steelewheels1365 7 ай бұрын
@Project_Pat it didn't spread as evenly. It kind of pulsated. Plus the handle won't come off. Did yours?
@Project_Pat 7 ай бұрын
@@steelewheels1365 I believe the hose unscrews from the bottom of the handle on mine.
@steelewheels1365 7 ай бұрын
@@Project_Pat I'm talking about removing the handle from the gun to replace the filter to clean it. You didn't have a problem with that?
@Project_Pat 7 ай бұрын
@@steelewheels1365 No, sorry I haven’t had that issue. Wish I had some advice for you.
@kingjtrill9440 7 ай бұрын
MUSIC ON POINT
@josephdueh 7 ай бұрын
Where did you order them from? Looks good
@Project_Pat 7 ай бұрын
Thanks!!! LMC Truck. Pretty good quality. No complaints.
@garyblevins5990 8 ай бұрын
Where did you get the extension to go on your avanti sprayer?
@Project_Pat 8 ай бұрын
I got it at harbor freight with the sprayer. It was separate but right next to the sprayer.
@tommybiggers8496 8 ай бұрын
Mid
@v8rangee 9 ай бұрын
Im getting given a red one soon. Cant wait.
@Project_Pat 9 ай бұрын
Nice!!!!! Manual or auto? FX, FX16 or a GTS?
@stormbreaker170 10 ай бұрын
Tac welding, and mig in general is the easiest form of welding, almost no skill required, and the welds will not hold the same as stick welds or Tig welds. Straight red neck shit
@CUTTERUPROB 11 ай бұрын
I would recommend to put a protective wrap on the airdog likes. Other then that its looking good
@Project_Pat 11 ай бұрын
I’m honestly thinking about swapping all the lines and using AN fittings.
@richardogden2249 11 ай бұрын
Looks like a good job. Not using all of a patch panel is smart sometimes.
@Project_Pat 11 ай бұрын
lol. There is a very long/entertaining story as to why I didn’t use the whole piece. 😂🤣🤷🏻♂️🤦🏻♂️.
@MADDCHOPER68 11 ай бұрын
Looks nice doing that to mine now but 15% out cold got to wait😂
@Project_Pat 11 ай бұрын
I’ve burned a lot of wood to get this project to where it is. 😂. I usually only have time to work on it in the winter. It’s tough. I feel your pain.
@fabuloussixxx9126 Ай бұрын
How are you sealing the bottom corner? Near where the seat belt hooks to. My son just got the new floor pan, rocker and corner on but there's a couple spots that are wide open. Body lines match, door is straight and space great. Cut and fill in new peices?
@wesfer1 Жыл бұрын
Thought you were about to rap for a second
@Project_Pat Жыл бұрын
That’s my other channel 😂🤣
@cfb36 Жыл бұрын
Results look pretty dang nice! Did you pull it apart to clean the coils separately and how’d you clean them? I’d be hesitant to bring a wire wheel near enamel coated cotter wire…😅
@Project_Pat Жыл бұрын
Thanks. No I just cleaned up the outside. Didn’t crack it open. I was tempted to but figured this was good enough.
@powder600 Жыл бұрын
$39.99 per gallon verses $23.99 for T6 Rotella. I'm sure the Doc's oil is good, just not sure it's worth an additional $16.00 per gallon good. I'm currently running Doc's filters, seem to be doing well.
@Project_Pat Жыл бұрын
I’m a big fan of T6 personally.
@jjfletcher1366 11 ай бұрын
Schaeffer is all I run in my duramax and I’m going to give this a shot next. I always run the large PPE oil filter and always use hot shots additive so this being 40 and not 60 a gal I’m already doing better then it has the additive in it already!
@Jon-O. Жыл бұрын
Yeah the fuel filters by wix arent even made to the same spec they donot keep water separated!
@Project_Pat Жыл бұрын
I’ve run Wix oil filters but never messed with their fuel filters.
@jaswindersingh-qw2qo Жыл бұрын
How much would u chsrge if i bring my truck to u
@Project_Pat Жыл бұрын
I don’t do it professionally….this is just a hobby project truck.
@ChambersFamilyOverland Жыл бұрын
I’m intrigued by this. I’m a hard rotella guy in my Cummins…
@Project_Pat Жыл бұрын
Same here…..No complaints whatsoever about Docs but I went back to Rotella on the next oil change.
@rodknockmedia5498 Жыл бұрын
Damn. Where are you located. I can’t find a shop anywhere around my area to fix my cab corners. They all say they don’t do cab corners
@Project_Pat Жыл бұрын
I’m in CT….but this is just a hobby/project. First time doing bodywork. Any reputable body shop should do cab corners. 🤷♂️. I would think.
@justinadams159 Жыл бұрын
Nice man. Thats a hell of a lot of work. Ask me how i know
@Project_Pat Жыл бұрын
Sure is……wish I was done. Lol.
@justinadams159 Жыл бұрын
@@Project_Pat how much more you got? Im in the middle of doing the same on my f150 project truck. Second one olive done. Im replacing the floor pan this afternoon actually
@Project_Pat Жыл бұрын
@@justinadams159 All the metal work is done on the cab, I have good doors, fenders are prepped, but the bed needs some tlc. Problem is it’s all apart and I only work on it in the winter. There isn’t a part I haven’t blasted and painted, or replaced. Everything is new or looks new.
@thefastlane1982 Жыл бұрын
Where did you get cab corners?
@Project_Pat 11 ай бұрын
@@thefastlane1982 They came from LMC Truck. That’s where I got all the replacement panels.
@turboflacko946 Жыл бұрын
I want the bently coupe and damn i have to do this on my truck 😢
@zts_star Жыл бұрын
And here I have summer depression :")
@Project_Pat Жыл бұрын
Where are you from?
@zts_star Жыл бұрын
@@Project_Pat asia, a pretty country with pretty bad ppl call Bangladesh
@docsdiesel Жыл бұрын
Thanks Again for the review! We apologize for the box, we are shipping this a different way moving forward so it will not leak and will not happen to future customers! Looking forward to working with you more in the future! Keep Truckin'
@Project_Pat Жыл бұрын
Honestly a very tiny bit of oil made what looked like a big mess, but it wasn’t that bad. Loving the products! Trucks running great.
@thesealerguys Жыл бұрын
What year.. had a 97 manual
@Project_Pat Жыл бұрын
It’s a 95….auto.
@Project_Pat Жыл бұрын
Omg…..worst audio ever😢. My apologies
@jayroberts636 2 жыл бұрын
Good deal man the best way to learn is to do it yourself because afterwards your experienced and you know how to do it right or wrong if you do it wrong it’s just a learning curve and now you will know what not to do
@Project_Pat 2 жыл бұрын
I agree totally. Like the old saying goes, there’s a first for everything.
@simmcowaPang122 2 жыл бұрын
Good shit man!
@Project_Pat 2 жыл бұрын
Thanks man, appreciate the view!
@Project_Pat 2 жыл бұрын
Honestly…..who is ready for springtime!!
@CUTTERUPROB 2 жыл бұрын
TRUCK IS LOOKING GOOD ! gald i can help guys when i can
@Project_Pat 2 жыл бұрын
Your videos are help enough. Taking the time to ship me a stupid little part is a testament to your nature. I thank you and appreciate your time.
@nickatfluidampr 2 жыл бұрын
👀