I still drive by the old Wang Labs building. I want to use one of these so badly haha
@redfiat5 ай бұрын
Hi, I have a Wang APC I am trying to fix, do you have any documentation that may be helpful please? I've found the Wang PC tech ref and schematics on bitsavers but those do not cover the APC. thanks
@vlk19675 ай бұрын
youtube.com/@BaudBand?si=6jBOe7JzHuQJEygA
@vlk19675 ай бұрын
Check your Keyboard for rotten foams. You can use it only with your Fingertipp. Start only with graphikcard and Winchester Controller. Remove all Others. APC Board ist connected to daughterbord (Slot 1) next the Grafikcard and in Slot 8 the Winchester Controller.
@redfiat5 ай бұрын
@@vlk1967 my keyboard leds stay on 01101 which is a fault code but I don't have the service information for the APC to find out what it means.
@vlk19675 ай бұрын
@@redfiat Check the SIMM modules, should 120ns, an the connection to the holder. Max. 2MB (8x256kB).
@redfiat5 ай бұрын
@@vlk1967 thanks, only has 2 simms installed, swapped them around and got a different error code 0 01100 instead of 0 01101 but still not output on the serial port or screen. not sure what the serial port settings are though. I tried various baud rates but got nothing, apart from and odd character that looks like noise when I turn on the computer
@techdistractions6 ай бұрын
amazing - what a lovely looking set up!
@DandyDon110 ай бұрын
I suppose if you are located in the USA Batteries Plus can build a replacement battery pack for you.
@DandyDon110 ай бұрын
Writing Winchester, that's curious. Any example I ever saw of a Winchester drive had a platter much larger than an 8" Quantum Q2040. :)
@DandyDon110 ай бұрын
BTW what did you pay for the WLTC, and have you found it useful to run applications you were unable to use before? Bedankt.
@MrFlyingmonkeypants10 ай бұрын
I remember when these were the new thing, replacing the 8” floppy that had less than half the capacity as I recall. Thanks for bringing back the memories to this old Wang 2200 programmer.
@ikkiiiieee Жыл бұрын
Do you happen to know if the spindle knurl wheel bolt at 0:39 is m7 or m8 thread?
@vlk1967 Жыл бұрын
It is M8x1 rh. Only spindles of the MK1 have this feature. The later one are without the thread.
@ikkiiiieee Жыл бұрын
@@vlk1967 I have the mk2, which is the exact same body, same black everything, but with exposed bars behind the tailstock. And for some reason it doesn't seem to have the thread. Next models have a hole in the spindle to be able to remove the chuck when its tight. But on mine, I have absolutely no idea. Seems they removed it on the 2nd and brought it back in a different fashion on the nexts.
@vlk1967 Жыл бұрын
@@ikkiiiieee the thread is only for use with this old drill chuck, without key. The spring loaded jaws where adjusted with the steelrod and the knurl wheel. If you have a drill chuck with key, the thread is unnecessary.
@spmdroid Жыл бұрын
Many thanks!
@mionante5956 Жыл бұрын
keep it up damn
@Dodi-nz3fd2 жыл бұрын
please inform, the address of the official distributor who sells emco unimat sl lathe lathes in Indonesia
@vlk19672 жыл бұрын
Hi, the latest sl model are produced before 1980 i think so. Try to buy a second hand.
or look for the russian universal 2, www.google.com/search?q=%D0%A3%D0%BD%D0%B8%D0%B2%D0%B5%D1%80%D1%81%D0%B0%D0%BB+2&client=firefox-b-d&channel=trow5&ei=j_CWYqfdA4edkwXg04iYCA&ved=0ahUKEwjn4IvBuov4AhWHzqQKHeApAoMQ4dUDCA0&oq=%D0%A3%D0%BD%D0%B8%D0%B2%D0%B5%D1%80%D1%81%D0%B0%D0%BB+2&gs_lcp=Cgdnd3Mtd2l6EAwyBAgAEBMyBAgAEBMyBAgAEBMyBAgAEBMyBAgAEBMyBAgAEBMyBAgAEBMyBAgAEBMyBAgAEBMyBAgAEBNKBAhBGAFKBAhGGABQnQxYy1xg3oQBaAFwAHgAgAG7AYgBmQWSAQMxLjSYAQCgAQKgAQHAAQE&sclient=gws-wiz
@paultrimble93902 жыл бұрын
Yeah pay for something hard earned money 💰. And pay high shipping charges and gets packed cheaply or shippers look like they dragged it behind the truck to the house. Sucks.
@paultrimble93902 жыл бұрын
Good job. Man these unimat making big comeback. If u do more videos I’d bet get lot views. I like see good video how got it set up. Looks like nice set up. Thanks stay safe from ur ole hillbilly buddy. In West Virginia.
@paultrimble93902 жыл бұрын
I like to be able to go slow and have torque still. Idk, but make turning bolts,screws easier. When thread by hand u turn slow.
@paultrimble93902 жыл бұрын
Nice 👍🏻
@paultrimble93902 жыл бұрын
Nice set up. Still have ,use it or get bigger machines.
@visionsx82 жыл бұрын
Wow thank you so much, same as my first PC but with PC 350/33C and 725 keyboard instead. Brings back a lot of fond memories, always love the design and the keyboard. I still keep mine in pristine condition.
@marvincorea84182 жыл бұрын
Hallo, könntest du mir die eingescannte Version der Anleitung per E-mail zukommen lassen? Das würde mir sehr helfen. Liebe Grüße
Hey friend, what is the purpose of the correction? Don't you get too much steel? what kind of tool and what support do you use?
@vlk19673 жыл бұрын
Hi, the goal was to increase the gap 0.15mm on the mandrel of an hollow die. The tool is a 3.00 mm, special by me prepared, "Endmill" driven manually by a "Mannesmann GTV 1000" up to 100000rpm, mountet on a DIY bridge.
@vlk19673 жыл бұрын
The "Bridge", white plastic guy at 3:00 on the right upper corner in the background.
@machinist_matt3 жыл бұрын
Beautiful machine!
@luismiguelgramagerevert97543 жыл бұрын
Really nice, incredible... All new, original... What an experience unboxing a new Wang must be! Ein glücklicher mann, freund. Grüße aus Spanien!!
@fudgesauce3 жыл бұрын
Amazing find ... and it still works!
3 жыл бұрын
Bem elaborado seu projeto parceiro 👏👏👏
@fudgesauce3 жыл бұрын
The default display controller in the emulator is a first generation display controller -- eg, 7011 (80x24 CRT controller). This display controller doesn't have the box graphics overlays nor the alternate character sets that the game expects. You need to configure the emulator to use the MXD terminal mux, which then has 1 to 4 attached intelligent terminal emulators - that terminal emulation understands the escape codes to use the alternative graphics set and the display attributes (blinking, bright, reverse video) and box graphics. In the menu bar, pick the "Configure" menu item, remove the keyboard and CRT controller I/O devices at 001 and 005, then create a MXD terminal mux at /000. Hitting "OK" will cause a reboot, and then everything should work OK.
@luismiguelgramagerevert97543 жыл бұрын
Wow! That´'s nice! You are the WANG's master for me! I really enjoy looking your videos... and learning from you! Eine Umarmung aus Spanien ;)
@TheDIMONART3 жыл бұрын
Hello, can you tell me what diameter of linear rods/shafts in this lathe?
@vlk19673 жыл бұрын
Hi, 12mm and 8mm.
@gemini69993 жыл бұрын
Man, as a systems engineer with Wang for more than a decade, right through the late 70s and 80s boom times, if I had for a buck for every time I went through that, I'd be rich.
@inyongjosgandos3 жыл бұрын
Woow good 👍
@slicktires20113 жыл бұрын
Is the structure made of cast iron?
@vlk19673 жыл бұрын
Yes, it is.
@fa4970073 жыл бұрын
Do you have some pinout or schematic ? I'm interested as I'm starting the repair for my dead WLTC and was figuring out if it was possible to connect it to an external screen. Thanks.
@vlk19673 жыл бұрын
Hi, sorry i have nothing. there was a special cable to use some rgb/cga monitors with this laptop. i dont have it. sometime, shoul i be succesful with my experiments, i will upload it to youtube.
@fa4970073 жыл бұрын
@@vlk1967 ok, Thank you.
@damarcastro7683 жыл бұрын
Muito bonito gostei fiz um quase esse tamanho caseiro
@jayeverette3 жыл бұрын
Hi! I just found a WLTC in our garage in great condition. I plugged it in and tried to turn it on but got black lines one the screen but no lights or anything. Any idea on what could be going on? I haven’t tried to open it yet
@vlk19673 жыл бұрын
You must! Disconnect the internal battery.
@jayeverette3 жыл бұрын
vlk1967 I tried that but still nothing. Could I have fried the power supply? It’s been in storage for over 25 years, but I was hoping to see something come up.
@vlk19673 жыл бұрын
@@jayeverette have you tried without internal and main accu?
@jayeverette3 жыл бұрын
vlk1967 yes and unfortunately no lights or anything. Hopefully I didn’t kill it!
@vlk19673 жыл бұрын
@@jayeverette can you test your power supply, should 18V AC
@luismiguelgramagerevert97543 жыл бұрын
Hello. It´s a very nice computer. I recently have adquired one, but i´m unable to run it. I haven´t any disks. It runs, but in screen appears "Invalid configuration information - please run WWSETUP program" and "Diskette drive 1 seek failure". Could you help me, please? My personal computer level is no so high! Thank you very much!
Do you have a harddrive and two floppies? What kind the are, which is booting. What is your location? Skype? Zoom?
@luismiguelgramagerevert97543 жыл бұрын
vlk1967 hello and thanks for your response. I’m form Valencia (Spain). But my english is not very gold, so i prefer write and read it than speak (it’s more difficult to me to understand). If you agree, give me your mail and i send you some images, and talk by mail. My mail is [email protected] and you can find me in Facebook with the same name
@luismiguelgramagerevert97543 жыл бұрын
vlk1967 Another think: my Wang has a harddrive and two floppies (3 1/2 and 5 1/4)
@luismiguelgramagerevert97543 жыл бұрын
vlk1967 sorry, but I don’t know when send you some images here. I ‘ m waiting for your response. Thanks a lot!!
@jinaamvideo20023 жыл бұрын
What is the price of this machine?
@vlk19673 жыл бұрын
hi, not for sale!
@jinaamvideo20023 жыл бұрын
What is the price of this machine?
@fudgesauce4 жыл бұрын
I don't know what differences there are, but here is another listing that also claims to be version 4.0.1, but has a date of 11/07/90 wang2200.org/vmedia.html?diskname=vmedia%2Ftoolbox.wvd.zip&filename=TBO.ZAP
@fudgesauce4 жыл бұрын
Very nice! Do you have working equipment that can read Wang formatted tapes? I have some streaming cassette tapes and some QIC cartridges that I'd love to have captured. I have reason to think there is some really interesting stuff on them.
@vlk19673 жыл бұрын
sorry for delay, have no equipment for tapes!
@qeku4 жыл бұрын
Hi, i have the same keyboard, and the A key does not work in any octave. Did you have a similar problem? cheers
@vlk19674 жыл бұрын
Hi, yes the problem was with two keys in any octave. But bad sound not no sound. Good luck
@fudgesauce4 жыл бұрын
Version 3.0 of wangemu was just released a day or two ago. It can emulate MVP OS and the intelligent terminals, which means @MARTIAN, PAC-MAN, and some other games can be played now.
@HughProf4 жыл бұрын
Do you any other applications? In the late 70's I remember a horse race simulator on the 2200. I would love to see it again!
@vlk19674 жыл бұрын
like this kzbin.info/www/bejne/gZClgJ6Zo5WtoMk
@spenglervideo4 жыл бұрын
The current version I have is dated 23-OCT-81... i wonder what will be different!!!
@spenglervideo4 жыл бұрын
when i saw your video, i decided to resurrect PAC-MAN for my grandchildren. I obtained a listing from another source, but without the REM's. I still program in BASIC2 (aka Niakwa's NPL) everyday. It's a super fast, super functional programming language. It's been a joy to work with for over forty years. The newer stuff is great to, but, too much crapola. I'm gonna get a MAXIIMITE and convert this to MSBASIC... just for fun. Thank you so much.
@spenglervideo4 жыл бұрын
i would like a listing, please. Use LIST SD take a screenshot, hit ENTER, repeat.
@vlk19674 жыл бұрын
kzbin.info/www/bejne/aJ_Si2yliK56kKc
@spenglervideo4 жыл бұрын
Not familiar with "PRISM", buit, "IDEAS", yes. Wang Professional Computer "BASIC2" has been fully ported to DOS/WINDOWS.
@spenglervideo4 жыл бұрын
This version of BASIC has been fully ported to DOS, UNIX, LINUX, WINDOWS, NOVELL, AIX, HONEYWELL BULL & SuperDOS, environment.
@spenglervideo4 жыл бұрын
I know basic2, basic2c, and npl very well. LIST DCT/D23,
@vlk19674 жыл бұрын
The HATTRICC.BS2 file, written by my father is lost. It was a solution to run 2200 Programs on a IBM-Clone. Before NIAKWA. And i dont know how it works. Some wang costumers in austria and eastern-europe used the HATTRICC Software. So he says.
@_bennox98494 жыл бұрын
🤮
@jakubcyndzer68654 жыл бұрын
Today minę Casio ctk-100 got completly dead [*]
@volkanozden33485 жыл бұрын
Hallo,ich habe ihre Video gesehen mit emco drehmaschine,wollte ich fragen ob sie das maschıne verkaufen möchte
@vlk19675 жыл бұрын
Hallo, danke fürs anschauen. Die Maschinen sind nicht zu verkaufen.