These trucks are garbage. I shouldn't have to beat on things with a hammer like a caveman to install something.

Good luck man!

Piece 'o cake. Out for a cruise next week 😂?

I bought the tool for $12 bucks and it don’t work worth a penny. I am going to try the zip tie method

The trials of Jean Gray continue.

My mechanic said to sketch to do try somewhere else u are the man I couldn’t panit car till i got this in cause door kept scraping ur a lifesaver thank u

Honestly, I use my phone for 99% of my filming these days. I airdrop the videos to my computer (I realize this is Mac specific), edit them. On the editing side I only do what’s required, I used to go crazy but when I was seeing less than 200 views, it didn’t make enough sense. I recommend creating a smaller workflow, shorten the videos a bit if possible and re-test some ideas, after about 30 days you’ll be able to make some tweaks and know what’s working. Lastly, even as a job, KZbin needs to be fun. Which is kinda hard to do when it’s a struggle, so I get that! I would focus on maybe 3 topics and go hard into those and/or maybe create a 2nd channel? On the website front, I am curious why it’s so expensive, happy to chat and see if I can help save some money there. I enjoy the content and your perspective of doing it like an actual person, not a brand or sponsored content creator. Keep going!

Sup bro and yes is still subscribed to your channel after all these years

Just a friendly FYI, based on the serial number that chest was made May 11th, 1955

Need to check for electrolysis

Did you have any issues with the water not draining properly? I see the hose goes up and then down into the drain pipe.

Did you have successful crimps on the double wire packard ends for the headlights?

The sound of money $

....now that's outside the box thinking. Nice. Thank you

Nice! And some helpful comments below...

I just put in a screw on oil filter kit to keep my system clean

Thanks for the easy install

Dang

Is my 2002 cavalier in the same placement im afaird to drive it any where dont want to blow a gasket since it was over heating before wish i could get help to fix it ugh 😑

How'd you remove the bolts on the calipers without enough clearance? Swapping my 78 El Camino pads out and there isn't even enough clearance to remove the calipers. They're fucking stock.

Why does it say steering column tear down when it's not!? Thank for wasting my time bro

Thanks so much for this detailed video. Best one yet!!

Awesome. Thanks

I hope you know how many people you've helped. I bought a new faucet and my portable has just been sitting there. I appreciate this video so much my dude. Thank you, thank you, thank you! Also there are people on Reddit that have this problem often and I will direct them to this video.

Clip is broke any ideas ?

That's a good idea but how did you get the sping out and why didn't you go ahead and replace the roller pin assembly?

Thank you for sharing your experience.

Here's a place that vacuum forms then like new again: kzbin.info/www/bejne/nmfIhYyMpbGCetk

Thank you guy's very much 🔧👍🙏👍🔧

You have a timing gear on that? I like the sound of those mufflers. I need to put something on my 383 to quiet it down some. I’m taking out the timing gear for a double roller timing set to get rid of my whine.

This shits not working for me.. probably a good thing though because the trash ass autozone bushings already busted and I just put them in today and after like opening and closing the door 25 times to check sag one already spilt lol

Is there a part number on the die set?

Y’all deserve more credit. Hawt dawg

btw for anyone watching this and would like another angle we show it again here kzbin.info/www/bejne/Z56Zk556qsqtodksi=RQo5A9s1w2zy8V4O&t=375

This shit is so aggravating lol

What is that that you have in your hand called and were can I get one tia

I heated mine up and bent it half inch on both sides with a hammer then I used a long bolt to suck it back up to the frame. lol I had a question though. On that frame rail theirs two tubes what r they for? One of mines broke the red one

New sub here

Nice unboxing and good luck on the build, I subbed your channel!

I just did this last night without removing the exhaust manifold. As much as I hate to say it, you are better off removing it unless you have a long extension to reach those bolts under the manifold, it's an absolute nightmare either way you go.

Did you ever find the issue I have the exact same problem

Just found you and subd. I really like the mix of 1 to 1 and models. Excellent job on the chasis!

Do it on the v10 and tell me it's easy

Eyes are worth more than $10. Thats what the tool costs to do this job properly. Some things should not be hacked like this.

Sometimes this problem can be fixed by adjusting the reverse lock out rod. This is a flat plate coming out of column in engine bay. Make sure it is all the way up when it is in park. This will cause the key not to return to lock position and key can not be removed

Do you think its possible to run some sort of T connections or something so you can still use the washer to? Obviously would have to switch drain hose everytime but im good with that! Thanks in advance 😊

Another red neck playing the 70 year old hot car movie that only proves the cleched and formulaic stupidity of that hackneyed and outdated follow the lead of the last generation of mindless followers.