Hello, I want to tell you about a problem I have. So I also removed the steering wheel of my 3008 manual transmission, because when I turned the steering wheel made a small gap, like plastic, as it touches some plastic pieces so I dismantled the steering wheel same procedure, then reassembled it the same way you did with the torque wrench, but when I reconnected the battery and turned on the engine the ESP / ASR warning light appeared on the on-board computer with the ESP anomaly message. I think I contacted the connectors correctly, do you know what could have happened, thank you very much in advance
@kmarko16 күн бұрын
Hello. I THINK that removing the steering wheel has nothing to do with ESP. In any case, try disconnecting the battery and reconnect it after about 5 minutes and turn on the ignition for 30 seconds and start.
@costa185416 күн бұрын
@@kmarko Hi ok I'll try to do this hoping that in this way it will reset and everything will return to normal, thank you very much for the advice
@dartanian884418 күн бұрын
Thank You but how clean ac condition?
@Ac7ionАй бұрын
In this video the turbo actuator is not getting vaccum, that is what the guy is testing in the video, when you start the car the turbo actuator rod should move down, if its not moving down there can be many reasons for that, the turbo actuator solenoid could have an vaccum leak inside, the menbrane could be damaged , the solution is nto order a new turbo actuator solenoid, the vaccum pipes could be disconected on the same turbo actuator solenoid, some of the vaccum pipes could have a leak, those are the main reasons for the fail, in this video if the solenoid turbo valve was working the siringe would move imidiatly after he started the engine.
@torlod7922 ай бұрын
Different procedure on 2010 model 1.6 HDi (definately not easy 🙂 )
@marijan-pavobosnjakovic54623 ай бұрын
Bravooooo majstore , šteta što nemaš dvije ruke
@vladshkuliy98364 ай бұрын
Super quest.
@KaareGHansen4 ай бұрын
There is already a hole in the bottom of the Steeringwheel to unlock the AB.
@christopherclark63534 ай бұрын
Hi mate can you point me in the right direction i have a peugeot 5008 registration MJ15EBK and its saying the levels too low where can i get the stuff please and can you send me the link where i can get the right stuff thanks
@victorryandellosa96165 ай бұрын
Can you please do a crankshaft sensor replacement video of the same car? Thanks!
@JackDaniel04105 ай бұрын
Great video, man! My battery is dead and I am going to replace it on my own. I have been looking for any helpful vid, as I anticipated it would be as kissing the hell. It will be, but with this video, the torture will be accompanied with much fewer f-words, sh-words, and whatever words one could imagine! THANKS! 👍
@andrzejkoscioek79005 ай бұрын
😊 dziękuję bardzo niech Ci Bozia w dzieciach wynagrodzi. (Zapomniałem gdzie jaki kabel idzie) 😠
@6toportal5 ай бұрын
I was looking to find what wires are the ones for the speakers, there's an adapter from the stereo but they are expwnsive at 80usd, a Hi-lo adapter is 15 and I don't ha e to take apart the head u ot, thanks for uploading this 👍🏻
@user-kf1qj8nw4m6 ай бұрын
i have the same error code with a scenic dci 1.5 2013. already changed map,n75turbo works fine but above 2200 rpm.between 1500-2200 there is a lag.whats your opinion?
@Banker.xXxXxX6 ай бұрын
hi Marko mine is going in safe mode on highway in the city not at all. Code po299 underboost of turbo. Could it be N75? Intercooler was already changed i cant change the whole turbo it doesn’t make any sense given that the car is driving great and gas the power. On highway after 30minutes goes into limp mode. I need help
@kmarko6 ай бұрын
I would definitely replace the N75. If that doesn't help, the turbo is bad. Does it not flow?
@Banker.xXxXxX6 ай бұрын
How do you mean flow? The car runs great he has a power, kickdown everything is on the place,he is not shutting the turbo at all so you can drive it in the city however Ou want it to be driven, full gas uphill downhill everything great but once you are on a highway it goes in safe mode 40 min later or sometimes even 2h later. there is no rule. I am realy at the end cuz mechanicher said only n75 and diverter valve to be changed but diverter was good during a test if that doesn’t work then new turbo :(
@Banker.xXxXxX6 ай бұрын
@@kmarko How do you mean flow? The car runs great he has a power, kickdown everything is on the place,he is not shirting the turbo at all so you can drive it in the city however Ou want it to be driven, full gas uphill downhill everything great but once you are on a highway it goes in safe mode 40 min later or sometimes even 2h later. there is no rule. I am realy at the end cuz mechanicher said only n75 and diverter valve to be changed but diverter was good during a test if that doesn’t work then new turbo. Audi q5 2.0 tdi 177ps
@Banker.xXxXxX6 ай бұрын
turbo is clean, no strange sounds or something like that
@Banker.xXxXxX6 ай бұрын
@@kmarkoCan you help?
@TheAmazeer6 ай бұрын
Electrovalve is out of order 😊
@vasil29076 ай бұрын
а где звук?
@viliamstraka56887 ай бұрын
does your car make a stututu sound when shifting or when you let go off accelerator ?
@f1kkyyАй бұрын
dude i have same problem, mine does when let go off accelerator ! i cant solve that problem for 3 months
@AdamDitheridge24 күн бұрын
@@f1kkyy Wastegate problem?
@issaiso89667 ай бұрын
Vielen Dank für Ihren tollen Einsatz. Ich habe das Auto heute tatsächlich repariert
@issaiso89667 ай бұрын
I have the same problem until now and I don't know how to fix it
@kmarko7 ай бұрын
you need to replace the vacuum machine
@kmarko7 ай бұрын
I will upload a new video with the exchange
@paulocasinhas27324 ай бұрын
Já meteu o vídeo? @@kmarko
@kmarko4 ай бұрын
@@paulocasinhas2732 I forgot. Wait 3 days
@paulocasinhas27324 ай бұрын
Thanks my friend @@kmarko
@nico100579yout9 ай бұрын
Ok. We can see that is no vaccum . What is the fix ?
@TheAmazeer7 ай бұрын
Turbo geometry is stuck needs disassembly and clean and replace used parts like chra
@dailystruggle276210 ай бұрын
Is it even cutting at all?
@micheljoniaux374511 ай бұрын
Thx Marko for this video. At 5:15 you have a small passage. What is the distance between the wires. BOSCH recommends always 135 cm , but it seems to me that there are no problems with a smaller distance. At 9:00 the wires are even at a smaller distance (I guess 10-15 cm) without problems .Can you give your opinion with your experience ?
@m1kael Жыл бұрын
Well, first you have to take the cover off underneath the glove compartment to get to a screw. Then there is two more on top of the back cover inside the compartment. Visibility is very limited to the actual filters. You have to take off the "lid" and pull out the old filters. Two suprisingly large filters. Then insert the new ones at an awkward angle and thats not that easy when the filters are very soft and will fold easy. I managed to do this myself but will not do it again, I think.
@user-uc5cj1uq6i Жыл бұрын
DANKE Marko. Du hast mir echt geholfen! Der Peugeot 5008 ist halt schon sehr speziell. Grüße aus Waldhessen!
@user-zj9ye6xt6m Жыл бұрын
Super la vidéo merci
@didiergabory Жыл бұрын
Comme l’amortisseur tombe sur le soufflet de cardan dommage 🤪
@tnteachertim Жыл бұрын
Is it even cutting anything? This seems, at best, suited to KEEP a lawn short, AFTER you've cut it short with a real mower. It doesn't look capable of cutting actual grass that may have grown for a few weeks.....
@agentNGI Жыл бұрын
Great video! I have the same car, but with fucking engine 1.6 vti by BMW. Today spring in this shit car spring was broken and your video is very helpful. Sorry for my english, but i'm Polish.
@sonofamortician Жыл бұрын
It does not seem to be cutting at all?
@gagi_czv6947 Жыл бұрын
🤔🤔🤔🤔🤔🤔
@salvocuscina9992 Жыл бұрын
How much quantity a tank like this takes? Thanks
@kmarko Жыл бұрын
about 3l - whole canister or to the top edge
@salvocuscina9992 Жыл бұрын
@@kmarko thank you for your reply I appreciate that
@jakubmalicki4643 Жыл бұрын
I think that the mower updates using a flash drive are useful because I have the exact same type at home, bought a few days ago, and it behaves much differently (it seems to me that it is more gentle on the lawn). please tell me what version you have, you do it by turning off the mower and holding OK when you turn it on, the version will be shown to you. Thanks
@kmarko Жыл бұрын
I don't have it anymore. I exchanged it
@jakubmalicki4643 Жыл бұрын
@@kmarko what happen?
@JackTekkel Жыл бұрын
So is it working or not? If I start the car it immediately moves the waste gate. So it immediately creates a vacuum. Are you testing for overboost condition?
@issaiso89667 ай бұрын
I have the same problem😭😭
@JackTekkel7 ай бұрын
@@issaiso8966I changed the regulator. Seems fixed now. I had an overboost situation.
@viliamstraka56887 ай бұрын
for me its the same but car is working good i think, only thing thats problem for me is that stututu noise when i let off the gas in neutral or when i shift to another gear
@dannymccann5 күн бұрын
@@JackTekkel Yo, same problem here. On startup wastegate fully closes under vacuum but 3k RPM I get limp mode P0299. When you say regulator, do you mean the "boost control solenoid", little orange thing back of the engine block? I've got one on order but dreading the replacement job...not even sure it is the problem
@JackTekkel5 күн бұрын
@@dannymccannyeah on the back of the engine. Also check the hose that runs up and sits between injectors with a little filter, mine was clogged with engine oil.
@jenik1337 Жыл бұрын
Ahoj, má to ,,zóny"? Daji se udělat?Díky za odpověď
@kmarko Жыл бұрын
ne, nemá
@jenik1337 Жыл бұрын
Ahoj, slyším Čecha (: jak si poradi s tim uzkym koridorem kde je 5cm mezi kabely? ...mam taky uzky prujezd jakoby na druhou zonu zahrady a zajima me jestli se tam dostane..dekuju
@kmarko Жыл бұрын
no problem... v pohodě..
@segipraks Жыл бұрын
ok
@segipraks Жыл бұрын
ok
@tsktr2197 Жыл бұрын
Dankeschön du hast es sehr gut erklärt. Viel Glück mit deiner Arbeit. 
@MoPoTime Жыл бұрын
Useless
@carmelobonavita Жыл бұрын
good morning, if I have not misunderstood at 0.25 m you say that the optimal distance for a clean edge is 23 cm and not 26 cm as the manufacturer says. Did I get it right?
@Fernandestres Жыл бұрын
Have two clients with the same problem. Gonna try that first. Thanks for the tip. Cheers from Portugal.
@Nurtured_by_nature Жыл бұрын
Pls guys I’m looking for a part but don’t know the name 🙈… if someone could identify what this round thing at 12:40 is… pls & thanks in advance
@gotobedandtickler Жыл бұрын
It's a electric vibrating damper pod... If you hold it to your ear with the two wires going to a 12v battery, it will be possible to hear the vibrations.
@Edward-rw3kq Жыл бұрын
Have I gone deaf???? I said.....have I gone deaf????
@frantiseksobotka5441 Жыл бұрын
Sap
@zoezebra4013 Жыл бұрын
this is not a replace, this is only showing location
@kmarko Жыл бұрын
yes, but I think the change is very simple. just pull up more
@zoezebra4013 Жыл бұрын
@@kmarko thanks, but the problem is I have never done it in my life so I wished you showed the whole procedure, i.e. do I need to drain fuel somehow first, disconnect tubes etc etc.
@brkix Жыл бұрын
Thanx for the video tho...have to do this to wifes car.
@brkix Жыл бұрын
I wish the idiot who designed this have a year long diarhea...
@felixrapha5701 Жыл бұрын
What size of socket is it at 16:14 please ?
@kmarko Жыл бұрын
21 mm
@felixrapha5701 Жыл бұрын
@@kmarko thanks
@elninodelavega77 Жыл бұрын
Sympa la chandelle, c est quoi comme marque ? 😂😂😔
@fredrandall5420 Жыл бұрын
like a silent movie need to talk through it, apart from that very informative
@MrMadeinthe80s2 жыл бұрын
Only price Ive found on this was for the nicer model and its listed at $550. Thats a steal. Too bad I cant find anywhere in the US to buy one. Looks like a Husqvarna clone.