Hi can bad swivel bearings cause my wheel to Angel over when turning full lock
@troopytech9467Ай бұрын
Definitely can if collapsing
@bicycleengineeringАй бұрын
@troopytech9467 ok thanks
@unpaved7040Ай бұрын
Any tips on how to tell when the housing bearing needs replacing?
@troopytech9467Ай бұрын
@@unpaved7040 drop the tie rods and turn the swivel left to right. If it’s notchy it’s time
@rodkuhn45Ай бұрын
👌
@rodkuhn45Ай бұрын
Sounds Right to me Cobber.
@naokotsuji31502 ай бұрын
good job mate
@nickwildsmith65377 ай бұрын
Great video Mr Dangerfield, thanks
@hosseinmasoumi24128 ай бұрын
In this model, the balance bar of the car is removed ????
@federicooddone19979 ай бұрын
Legend!
@mikewilliams639011 ай бұрын
Hey mate, what happened with the channel? Decided not to create new content in the end?
@freddyflores564011 ай бұрын
Great job! how often you do this job?
@shane8782 Жыл бұрын
hey Mate what type of headlights are you running
@troopytech9467 Жыл бұрын
Stedi carbon We have them on our store www.cms4x4.com.au/products/stedi-7-inch-carbon-black-led-headlight
@Brandoba Жыл бұрын
Do you know if I bought a hdj79 radiator bash plate it would fit to the hzj75 ?? Thanks mate
@troopytech9467 Жыл бұрын
Sure will
@Ambrolite Жыл бұрын
Is that Scomo's ginger cousin?
@noelburke1905 Жыл бұрын
Hi your video was great but I had a major fail the ball bearings fell out and bits of metal everywhere. My axil was OK do I replace the pice that fits into the cv joint or will it be OK
Ripper video cob bloody well done, what’s the rough time per corner?
@mthebone Жыл бұрын
This was the best video on how to replace/repair the swivel hub components. Thanks to you, I felt confident to do it myself and succeeded replacing the CV joint and bearings on my 78. Thanks Heaps.
@adamromanak7605 Жыл бұрын
Thanks for this video, even though I'll be working on a Patrol there are tips you've mentioned here that has taught me a lot.
@patricknjuguna2645 Жыл бұрын
Hallo sir how can i get the knuckle of landcruse 79
@troopytech9467 Жыл бұрын
Do you need a knuckle assy?
@patricknjuguna2645 Жыл бұрын
Yes sir at affordable prices so that I may able to sell here in Kenya
@aguyandhistroopy Жыл бұрын
Had one of them years ago, didn’t like being knocked around in the back of the troopy. Still have the dual stove in the garage somewhere, but now run the single freestanding cookers x2.
@troopytech9467 Жыл бұрын
All good units! I still use the petrol stove as I find it hard to beat especially in really cold temps. Im getting back into the petrol lantern just for the nostalgia and see how it fares in the new case
@sshahzadjaan9394 Жыл бұрын
اسلام علیکم شهزادبلوچ
@trevortrevo7583 Жыл бұрын
I like it a lot man thanks
@powerpoint5988 Жыл бұрын
Yea wicked death wobbles coming your way with that shimming method
@troopytech9467 Жыл бұрын
Haven’t had a problem ever. Out of all the views and comments you’re the first to bring that one up. Works for me.
@carlbickle94672 жыл бұрын
Christ alive..the noise levels!!!aaarrgghhh!!!!up...down...up..down..sort it out.
@troopytech94672 жыл бұрын
Only some people have this issue. Must have been a platform problem.
@andrewheadland93412 жыл бұрын
The blog would have been heaps better if we could hear what you were saying, the sound quality is crap
@robertomolina80682 жыл бұрын
Great video I have a 1999 105 series cruiser 6cyl petrol. Im wanting to instal a bigger radiator kit ( fan, clutch etc ) What do you recommend?
@shaungranger21662 жыл бұрын
For beginners the only sketchy part is the last bit with the locking mechanism for diff lock
@zeMasterRuseman2 жыл бұрын
exact same as an 80 series
@letmelickbud2 жыл бұрын
Thanks …. First time to change fuel filter in 25 years of ownership
@seanlawrence10062 жыл бұрын
Just the video I needed. Bought that upgrade along with belt kit yesterday. Cheers bloke, great video.
@noobishly662 жыл бұрын
is it worthwhile cleaning all the buildup off the swivel hubs when doing a general clean up of the underbody, or does it help water ingress?
@troopytech94672 жыл бұрын
Just a thing I do
@coopercruse58672 жыл бұрын
You dont have to remove the top swivel hub bearing pin it just swivels of .
@troopytech94672 жыл бұрын
Just a good thing for people to see
@coopercruse58672 жыл бұрын
@@troopytech9467 Fair enough.
@Suzykid0072 жыл бұрын
Thanks for doing this video Its Great
@jdmgm67653 жыл бұрын
quick question the lower steering arm stud is there any alternative way to tight the stud with double nut?
@troopytech94672 жыл бұрын
Stud removal and installation kit
@Gudetamaimmi3 жыл бұрын
Awesome video mate! At least i know i have been doing my bearing races right all this time too lol
@411lofty3 жыл бұрын
Mate do you have a wiring drawing for freewheel hub LJ-78
@peteoburrito9203 жыл бұрын
Thanks legend
@russtaylor49593 жыл бұрын
Great video !
@matthewtunbridge18083 жыл бұрын
You have no idea how useful this video has been, great work mate! Gave me the confidence to work on my own car.
@abdulmtandi23413 жыл бұрын
Great job bro ...i want to know how to lock a hub nut front .and how tight should it be ?
@troopytech94672 жыл бұрын
58nm
@timohare85753 жыл бұрын
thanks for the tip - what size thread is the nipple?
@PUUMBA4x43 жыл бұрын
Awesome vid mate. Watched a dew of your vids and im spewing u dont make them anymore. Doing this tomorrow wish me luck. Do u put ur lockers in to stop when the cv slides into the diff for dropping
@stephenfuller37483 жыл бұрын
Hey mate we're about did you get radiator hoses from thanks Steve
@troopytech94673 жыл бұрын
shop.cms4x4.com.au/
@michaelnugara13 жыл бұрын
Awesome vid mate. Where have you got your workshop located. Thanks for sharing
@PUUMBA4x43 жыл бұрын
Cms4x4 on fb mate
@jackfoster33023 жыл бұрын
What grease ya use mate?
@kezg6163 жыл бұрын
Did you share more of your secrets in a latter video of how to replace the bearings not just the repack?.. if so please share the link. Thanks,, !! Great video and l love your style
@outbacknomad99393 жыл бұрын
Good stuff .yer im a 79s owner knowledge is good
@FrothinOz3 жыл бұрын
Cheers for the informative video mate learnt heaps, doin us Aussies proud
@karlosxzy3 жыл бұрын
Would be great to redo a few of these videos with better aspect ratio and higher resolution. Instructions are good, but better quality video and closer angles would help heaps. Thanks legend
@phalanx38033 жыл бұрын
so sitting around 90℃ is is OK? if so i am gonna need to by pass my AC cutout.
@troopytech94673 жыл бұрын
Ac cutout is 104c ish
@phalanx38033 жыл бұрын
@@troopytech9467 mine's cutting out around 85
@phalanx38033 жыл бұрын
@@troopytech9467 video was definitely helpful I've been around a 1HZs my whole life but not a turboed one and I just got one second hand and the previous owner never did a radiator upgrade so I did had me confused cos my gauge was saying my engine was close to overheating but my egt's are cooler than before 350 ish they used to be just over 400 with the previous radiotor.