Sloved? ;-)

Thank you. Your video helped me to clean rust out of my starter and it works perfectly now. Thanks 🎉

As of 7-15-24 this vendor on eBay has the Atwood gas vavles in stock (24 7 partsinc (40011). Hope this helps some of y'all I know what a pain it is to try to find this gas valve.

your video is not that good. all I see pretty much is your hand covering what your working on

Thanks for the tip! I saved my neighbors fishing trip!

Merci beaucoup ! Je ne vous connais pas ,, papa et fille . Félicitations à vous deux 😀👍🏽

Do you punch holes in the bottom of the bag?

Thank you for this video. It led me to my sudden increase in oil use. Here it is 2 years after your post and O'reilys sold me a bad one for my 2005 2.5 Altima. I replaced it and it hasn't used a drop since. I contacted Corporate and they never said they were sorry or that they plan to do anything. I will never buy from O'Reilys again

Information was presented very well. Very good video . This really helped me fix my Daughter’s Altima.

sometimes check the cam shaft sensor see if any oil is around it u don't have to replace it but just get the ring that goes on that sensor and replace it slight fix js another way to see if ur oil is running low

I so glad you sloved it. I burned a 40lb motor because it was consuming all my oil. I need that for my igloo.

hi... my old blue knob burnt yesterday but the unit still works.. do you know why it burned and do I need to worry about it?.. ty

Why wouldn't you show the removal of the starter everybody on here wants to know how to take it out including me and how did you get it back in?

The whole point of looking at the video for the starter is to see how you uninstall and then install the starter!!!

My 2018 nissan altama used a quart every 100 miles replaced valve cover and pvc valce now it uses no oil thanks for info

Hey guy could you possibly take a photo of where the rings actually lie you had your hands all in the way can’t tell what your doing

that valve is $200.00 on Amazon now !

late to the party, but does that mean we cant freely rotate it over once we get everything together? since the tensioner is used via oil pressure. ive rotated it and the cams and crank always make there way in time. just want a clarification. because sometimes theres slack at the top and sometimes theres not. thanks

Good video. How many km before rebuild and why?

Can you send me the Amazon site you purchased the gas valve, thanks Tommy

On my Nissan Factory service manual the it states 75ft-lbs, then loosen all the way, then 26-32ft-lbs, then 75°, and another 75° For the cylinder head bolts. I wonder if that was revised at some point. Mines a 2003 Sentra SE-R

Do it leak water

Gas valve not in stock now

Dude let me tell you I just went through a mission getting the two screws out because on searayss you don't have space to get to the bracket screws so I just pulled the guts to rebuild it for a 305 helped me out working the selonoid

Have this exact water heater/value and set up. Hard to find video that doesn't have the RV - electrical water heater stuff. Thanks for all the explaination and details. Time for me to do like you have and start with the Pilot assembly. Great video and details!

My Pilot light stays on. But it will not turn the big flame on when I turn it to on!?! How do I fix that? Thanks!

Did anyone had rattling?

Great job, thanks.

Excellent video

So, the short version to the story is the cat(s) destroyed your engine. After the rebuild, you discovered & isolated the cause here. Is it plausible at all for a failure to keep the engine tuned (good spark plugs) and the associated misfires…to be a contributing factor to the cat’s degradation and eventual failure? *In the majority of cases, by the time the problem gets this bad-have the misfires, back-pressure and debris already ruined the bottom end of the engine?

Nothing less than a baseball bat upside the head !!!

Can I swap an Alpha One v6 in place of a pre-Alpha MC-1 4 cyl.? Note: The spline shaft on the Alpha One is longer(need to swap out for shorter shaft).

Is there any way to tell year of Alpha One Gen 1 from the stamped outdrive serial number? My S/N is 0C685074.

I have an aftermarket valve cover $45, it's worked great for the last 5 years. Cheap & easy to install. Nissan parts are nothing but 🐂💩.

Awesome video! Thanks

What if i hit the reset and it won't do anything?

Followed your lead and my older Atwood now works again. Good job!

I’m sorry I can’t tell what you are taking off and I don’t know how, so you aren’t helping and I missed the part how you got the motor to stay up

Great video!!

Dude thanks for this situation solved

great video, just bought an old RV with this assembly and found your video. excellent walk thru, look forward to tackling this

Holy cow can hardly hear you woth bird in background….

How much was it burning before

Did you have to remove the heat exchanger to remove the starter?

Back again. The Atwood Gas Control Valve shown is no longer produced. Dometic bought Atwood and canceled all production forcing people to buy a new Dometic water heater. Sigh. However, IF you are able to find a Robertshaw 110-503 (Robertshaw Uniline, Brownsville, TX 951-734-2600), it will indeed fit. They can direct you to a reseller or maybe you can order directly from them if you have a business. I have also seen adverts for the 110-503 from Grainger (most expensive - but still much less than a new water heater). You will need a 1/2" reducer bushing to use your same inlet fitting. The only other simple mod needed is to enlarge the hole for the inlet gas line so it will easily mate with the fitting in the 110-503. I did this with a rat tail file in about 5 minutes. Hope this helps.

*100% best **Generater.Systems** I have used. A test for hurricane prep here in Louisiana: three AC units, 5000, 5000 & 8000, 3 fridges, 2 device power setups, 4 flat screens....AND I had 40% of the power meter to spare.*

Nicely done! Thank you for taking the time to create this. It is most helpful! Best to you.

Quick question regarding the old valve... the temp lever which way is hotter vs colder?

The smart way to fix it would be to fix the water leak first!

That was perfect.