Merci beaucoup

This has been a very informative video for me. I need to get a hold of the 2 screws that hold the give to the hook. How can I obtain those screws?

Hi 🦾 first class

Nice video, thanks for posting

Thankyou !!

Great tutorial !!

I have a machine that the feet will move but the needle bar will not.

Great video! Especially hook placement

how SLOW does it go...you never went lower than 700 UGH!

Very much appreciated. Keep 'em coming, Neil. Thank you.

Where did you bought the sewing machine and how much

My 40 plus year old Juki LU-562 won't change stitch length - when pushing the button it will not hold in the groove. I feel when it passes it. Is it possible it worn out???

Hi, thanks for the video, very helpful! When I try to change the stitch length on my singer 300w, I can only turn the hand wheel about half an inch even with both buttons depressed. Any idea what’s up with that or why I can’t adjust the stitch length? Thanks

Buenos dias cual es la diferencia entre 562 y 563? Gracias

Hi this was very useful! would you mind doing a video on all the parts of this series machine abd how to use it? i’m in need of desperate help! Thank you so much

Hi I want to put a direct drive servo on my Juki 1541s do I need a special direct drive servo or can I use a thousand watt one I bought on eBay?

Thank you for taking the time to post your video...... I was able to fix a problem following your instructions.

You did a good clear job of explaining timing adjustment. I always say hook point to neeldle clearance is no light between them without them touching each other. I think it would be good if next you would have explained adjusting the needle guard. With these tight tolerances, any side needle deflection and good bye hook point. Just for added thought, most of these machines are old. Cup screws get worn as well as other parts and normally they have been worked on by many people of different skill levels. If you've owned a machine a long time then you know its condition. If you've recently acquired it, best to go through it. These are tools for doing real work. Don't want any downtime.

Hello there guys! I have a direct drive motor on my Juki 8700H heavy duty model it’s 1000watt eBay direct drive I installed myself overpowered for that machine I’m sure. I would like to put that motor on my Juki 1541s but the Juki 1541 shaft is bigger and I would need the proper shaft collar for the 1541 not sure what size that shaft is or what that shaft collar is called or how to order one I could use some pro advice for that. Also they claim those motors are for light duty machines and maybe medium duty it is 1000watt though would you say that would work for the application I want to use it for? Main reason is I would like to get rid of belt altogether I have a regular 750 watt servo on it now. Thank you for any advice you could help me with and sorry if I rambled lol

Thank you so much for this video super informative

Question, at the end about the walking foot…I’m wanting to raise the rear foot a little when it’s in the down position. It dents the leather as I feed it through and I think if I can raise that rear foot it’ll resolve that issue. How do I raise that?

My new 0303 D machine stitch length was on 5. However, the dile - knob was very tight. I didn't use forse, instead, I unscrewed the knob mechanism which apeared fine. Problem is the stitch length is stuck on a long stitch about 7mm long no matter what number I set the dile-knob on. Can you help please?

Thank you so much!!! I really appreciate your detailed explanation and close up video! You’ve saved me loads of time and repair bills!

Hi there, thank you so much for the video, I just purchased a ikonix KS 335A which looks just like yours. I'm running Nylon 69 as this was recommended, but the thread keeps on unraveling and birdnesting on the bottom, any help would be greatly appreciated. Thank you 😊

Cómo montar artillería máquina triple arrastre singer 211

كم الثمن يود شحن الاسكندريه

Great job what I was looking for. Ty

Hi thank you for your video, very useful. My stitch button isn’t entering the groove of the eccentric mechanism.. the mechanism seams to be off a little to the right. How can I fix that? Thank you in advance

Great video!!! Very helpful, thank you.

Outstanding! I wish this had been available ten years ago, when I bought my LU563. I haven't used it for a while, and it was not being very cooperative. Thanks to your video, I think she's purrin', again.

Where can one find the coils of that machine, thank you

Do you have a parts list to convert a 562 to a 563?

Great video, it's been a big help. I didn't notice you mentioning anything about the oil level in the reservoir for the hook assembly at all though. And isn't there any way to oil the mainsheet bushing by the hand wheel?

Great video. Thanks for sharing your knowledge with us. I just bought a used Juki LU562, and I hope to use these techniques to make my machine sew as it should.

You might be able to help. Ive tried to remove the bobbin carrier. I've removed the 3 screws but the bobbin won't lift out. I think there might be thread caught between it and it wont rotate.

Absolutely amazing thank you

Hello neil. Could you please do a video on how to set the stitch width and do a trouble shooting video. The amount of movement for my widest stitch and narrowest stitch is only 1/16” wheel movement. And it doesn’t seem right. There’s way too much room that’s not being used at all. It’s a singer 221u566a also. If I hold the button down and turn the wheel, it doesn’t have very much adjustment that’s usable. And my stitch should be able to go much wider. Thank you in advance.

Do you know where i can find a tutorial to change out the presser foot bar on the juki Lu-562

Sir , I have a Paff 335, very recently I had a problem of tagging . When I pull down the tagging bar feeddog is not moving reverse. Please help me to solve that problem. Thank you in advance.

You just taught me things I didn't know I needed to know :) Very informative video, thank you sir!

Thanks for the helpful video! I bought a "non working" 111W155 to do my own upholstery on a car restoration project. About 6 hours ago I did not have a clue how these worked. I will keep the story short by getting to the punch line, which is there are two sliding cover plates on each side of the needle/foot area, which at first glance look identical, but turns out they are not. I am sure you are chuckling right now because you know what the important difference is. The upside is I needed to get familiar with the machine anyway and made all the little adjustments in your video, and after 6 hours of frustration it made me laugh too, when I realized that all I needed to do was switch those two plates around because one of them has a recess in the bottom of it so the thread can pass over the top of the bobbin case.

You mention at the end, lining the plunger up top with the button on the bottom up. Mine appear to be off now, what do you do to line them up? I was trying to increase my stick length for the first time and I think I goofed it.

Just what I needed. Thanks!

Why does my machine cut thread when it goes through takeup spring?

Could you please make a separate video on just the bobbin release finger? how to time and adjust the finger itself would be amazing.

You are The Man Neil. Thanks

Hey Good Morning! I hope you will be fine, Kindly make a descriptive video on Juki DNU-241. It should all setting of machine included. Thanks

Thank you sir. Great video .

Fantastic video. Can I ask how I slow the machine down. Minimal petal press and it takes off full speed. I have slacked the belt and taken the take up on the clutch lever and pitman arm to the petal like you showed in the video. The machine runs too fast

Hi! I have the same sewing machine just different brand but exactly the same set up. I am having problem with the thread coming out of the take up spring all the time (that spring after the tension before looping to the lever) when I try to stitch on fabric. Have you experience something like that and if so, how do you fix it? I Would greatly appreciate any help. Thanks in advance.