I have the same dryer as the one in this video

I'm doing a Sporty mock-up and thinking similar. Need seat to perknup at back like the Trumpy but not too much.

What is that for?

Il mio continua a intasarsi il tubo aspiratore erba x che?

Fun tip you if you hold the button you can stop people locking there car's but you have to be within 50 metres

Dime

Lavadora

Me puede ayudar

Hola

Is this larger than a main gas flame? looks quite significant. How is the ring attachment for stability ?

*Fantastic*, found my error code E71 on my John Lewis JLWD1612 washer dryer. Broken wires to the temperature sensor ntc on the air duct at the front,. Was warned that this might happen by repair man. Two blue wires , they break where they are held on the duct housing . Thank you sooooo much

Great video. I suggest you do your cleaning at least once or twice a week, chickens can get very sick with the ammonia from their poop. Ammonia plus moisture and you will find respiratory problems with your hens

september 2022...still working fine🙂

what version of diagbox and Operating system are you using? Can't get mine to work properly with a mk1 c%

Yes, do the promised door video please!

Please link the automatic door closer you installed.

Take it off, you don't need it!

EHo

I wouldn’t cut the front…two mounting bolts, leave those to be your pivot attachment point. But your on the right track and have a good idea

Mango!

👋😁💖

Woofer :)

How many chickens do you keep in the coop? You may have mentioned in the video but I skipped through quickly, just trying to get an idea of the size.

It’s May 2021 now, it’s been absolutely fault free since attaching the heat sinks and with small fans blowing in from above.

I just bought the coop and find your video quite useful. I think about removing the perch or putting a piece of wood underneath it. Too sad you haven't made a video for the door yet.

Please do a video on the automatic coop door opener.

Awesome arrangement! What purpose is the box manifold rather than simple mount horizontal into ceiling?

Nice look at all the chips! Looks like they could all use heat sinks and a fan. My two onkyo’s have crapped out because the dsp and vsp chips overhearing

Filmed by me! :))

If the coop is cleaned regularly then there shouldn't be poop everywhere

There shouldn't really he poop in the nesting boxes

How do you decouple the Subs from the home?

So do you blow your roof...??

I couldn't understand anything

Speak UP!!!! Can't hear you, just another silent video ... errrr....

I bet you can attach a piece of plywood on the bottom of the perch blocking off that area they poop on the left nesting box

We need the demo

My tractor has one of these pumps mine was really bad all of individual pumps were stuck and every think else was stuck as well but it works now first step with tip ex mark the pumps drive plate and coupler and drive plate of the engine then remove the pump then with a sharp nife mark the rack each side of the rack forks no leveing no gaps loosen the rack forks then remove the diafram then the cold start by undoing the nut top right in pic then remove rack then clean everything with engine cleaner then soke the pump in wd40 for a day then with a flat screw driver put it in the pump that's stuck and twist if doesn't move turn the pump over half a turn and try again when it's free free off the individual throttle levers with plyers don't snap them off if they don't want to move keep sokeing in wd 40 until they do you should be abull to move them with you're little finger then reassemble then where the injection pipes fit on the pump remove the very top bit in side is a valve that will be stuck as well spill port valve I think it's called there is a vid on KZbin about that same as the injectors as well they will be stuck as well good luck I hope this helps

Rack was jammed to the left, so she wouldn’t start at all. The issue was a jammed piston in its cylinder. I rebuilt it and sanded down the rusted bottoms so it won’t jam again.

Is the rack free? Looks pretty gunked up. Try the Nuffield tractor forum for help.

Any updates?

What subs and amps did you end up using in there?

Here's a vid I made of this receiver through a heat imaging camera - kzbin.info/www/bejne/eWe0l6Cjf9-KodU