Thank you so much!!!! You’re video helped me so much, you are the best 💚

Thank you so so much! This was very helpful and I got my glowforge all cleaned :)

Prying the timing bet off the wheel is not a good idea. It will eventually lead to stretching the belt. It is better to use an Allen wrench (2.5 or 3mm) to loosen the wheel and let it slide toward the left to remove tension and allow the belt to fall off. Reverse to put the belt on.

Fantastic

Hello, do you know if I can connect the inline fan to a fume extractor? I don't have the option to vent outside & the fume extractor I have isn't strong enough by itself to extract all the fumes.

I can tell right now that I will be looking at this again. Hopefully I will get the hang of it soon. It's very simple after all.

Hello, love your videos they are alway so helpful!! I'm really struggling with making my glowforge recognize what parts need to be cut and which need to be engraved. But everytime I upload my svg files that I've converted to svg from Silhouette Business edition my glowforge only recognizing them to cut. and I know I can just change it in the glowforge software but some of my files i'd like to sell and I'd prefer them to be color coded so it is clear to whomever purchases my files what the design was meant to look like without confusion for them.

This is my first time cleaning because I’ve been scared to do it with Christmas orders. My print head is covered in Mdf dust. How could I clean that?

Thank you! I also watch this with every cleaning.

thank you so much for this clear video. I have had my glowforge for many years and my husband always has to put the belt back on because I couldn't figure it out. Your video made it so easy!!!

Thank You! Is there any difference between cleaning the Pro and the other Glowforges?

Amazing!

I probably missed something. When you did the name you have it in the red outline. I get that for where you want to cut or engrave. But when I do the subtract. I lose the red around the city and state. Any ideas?

Hi Lisa! Great video! Thank you! ImagR and Glowforge Pro newbie here. Getting married on Saturday and wanting to put engagement pics on 1/8 proof grade acrylic for a lighted table signs and have a couple of questions. 1) I like the results of the "see on material" views after using the software and reducing the gamma on settings but hat DPI, LPI and glowforge settings should I set for speed, power etc? 2) To mask or not to mask? 3) Which CO2 setting is best or should I select another? 4) Why did downloaded .png print the square and not just the cropped circle below? (Imag-r question). Thank you in advance for your speedy replies. It's crunch time! John

Thank you for the tutorial! I used it and it worked for me on my cameo.

Thank you for this tutorial! You made it so much easier for me!

I've done everything identically to you, any tips on why when I saved it as an svg in Silhouette Studio and then uploaded to GF the MOM letters are just outlined? I made them the color black. I'd like for them to be engraved, but it looks like it's just going to engrave the outline of the letters...? Thanks!

hello!! thank you for making this video! what if I am trying to fit two pieces that aren't square (i.e. abstract circle) how does kerf come into play with those types of shapes?

Finally tried it engraved settings and YES it worked so well

Brilliant video, easy to follow, nice clear instructions - my stakes look great - thank you!

I am still having the dotted lines when uploading to GF. Where did you upload the LLAMA from, your library or your downloads? I am not sure what I am doing wrong. I am uploading from downloads already as SVG (purchased in Sih design store) and then I trace, delete the old one and then do your steps. Still dotted when I upload =( I am not getting the error that says it will be dotted but it still loads dotted.

Just a handy tip if you don't have an adapter that fits your hose perfectly. I see a lot of 3D printed ones that address this problem and I see a lot of videos of people using ugly aluminum tape by the pound. Don't tape it AFTER you connect, tape the male adapter end BEFORE with blue painters tape. The simple answer to most of these misfitting hose to coupler is just build up about 1/4" of blue painters tape on the male end of any duct adapter, now slide the hose over the tape and, poof, perfect fit. In many case, don't worry about the clamps, just put enough blue tape on the adapter to it fits super snug, but if you want to clamp, you have this nice semi solid seal of the blue tape. All this talk about gaping of the hose when you clamp is taken care of.

Great video and I was able to get the Glowforge squeaky clean. However, I had trouble putting the belt back on. Everyone in our family tried getting the belt back on following the official Glowforge instructions, and we were all unable to replace the belt. Finally found another video that shows you can get the belt back on by loosening the right wheel with an allen wrench, replacing the belt, and then tightening the right wheel again. That step can save a lot of headaches if you just can't get the belt back on after cleaning the fan. Otherwise, your video was great and gave me the confidence I needed to clean my Glowforge.

Thank you!

Thanks a lot! very usefull. bless

Hi. Thank you for sharing all of these. I find it very helpful. What thickness of the mdf board that you used? Do you have a recommendation for this?

Amazing video! Thanks so much. It was very helpful and answered a bunch of my questions.

Fabulous video! I really appreciate the detailed explanation. This has made me feel so much more comfortable with cleaning my GF. Can you please tell me - you mention to be careful of print head when removing and re-inserting the crumb tray. Is there a reason why not to remove the print head first?

Can you add color to the back of the keychain

BEST Glowforge cleaning video ever! Amazing details and instructions. Thank you!!!

Thank you soooooo much!!!

You do a wonderful job teaching! Thank you so much.

It looks like Google changed its interface, everything is different, can you update for the new version?

Awesome video! Great and simple idea.. Thanks! Have you ever done an actual photo on something like this?

This video was a lifesaver for me. I’m new to this craft and was having such a hard time figuring out how to make all of the different layers work properly. Thank you so much!

Hello thank you so much for this video. I created a great ornament of my grandson recently by "HAPPENSTANCE" and could never create it again. I have a few request but I don't remember what to do. I have a question tho, does this apply to pictures that have a lot of background images as well?

no need to use chemicals to clean. Free and clear baby wipes works amazing! :)

how do you get your crumb tray so clean?!

Great video! Can’t wait to try it out. I have a question though….I received my Pro in April of this year (2021) and my top speed for engraving is listed as 1000. In this video your top speed was (Beta) 4000. Maybe they decided not to release this upgrade to the general user?

Hello I tried it and it worked thanks

Thank you finally a clear explanation. Your the best

Until today I am not decided to buy a Glowforge but after I saw some of your video tutorial i bought a Glowforge Pro right now!!! Thanks!!!

Thank you for posting this Glowforge video! I appreciate your help! Stay healthy and safe! Tricia

Where is that blue thing for removing the lens?

You Rock !!! thanks for putting out this video , quick question so are we suppose to keep track of the usage for every cut so we know when 4j0 hours is ?

But what about cutting?

Is the I Love Glitter font the only one that you can use to do the attached heart? Or is there another hack for using with other fonts to get the attached heart?

Have you tried to invert it so that you cut out the spaces but leave the roads?

Another great tutorial! Thank you! Binge watching all your videos….getting nothing done today! Lol