Hello, what spacer size do you send with the dual disk clutch? And how do I order a replacement ?

2:22 what do you mean push this off the end and it’s going to leak and you have to do it all over again? Does that mean if it’s not correct at first then you have to buy a new CSC?

❤

Been through 800 hp and 1200 hp mcloud clutch ..dissatisfied

OK so I was totally wrong .. I have set up many manual clutch linkage throw out bearings and you don't want them toughing the clutch fingers while the clutch is fully engaged.

If the Throw out bearing is touching the clutch fingers while the clutch is fully engaged, that throw out bearing is not going to last very long. The Silver Metal part is the Bearing .. The Green boot that has a spring inside, I would assume also has a slave cylinder inside the rubber boot. The whole thing is not a bearing.. It's a slave Cylinder and clutch throw out bearing assembly .

I saw another vid that recommended the sprung bearing be .200 air gap when fully compressed as well.

Do you grease the input shaft before you fit the bearing over the shaft ? Or does the input shaft never touch the bearing sleeve ?

I should had watched this video before all those videos! Very simple!

need a wrap😅

I can tell you first hand that a lighter flywheel WILL affect a daily driver the car will stall easier from a stand The heavier the car the more its effected

#1 tip, use the Velvet Hammer.

☠️☠️☠️☠️

love the whiz quiz cup for demo purposes, haha.

Hello sir! I hope you are well. I have seen the videos of your channel. Your video is very good but your video optimization is very poor 1. SEO Score is very low 2. No Title - Description - Tag SEO friendly 3. No Share Social Media Platform and many problems on your KZbin Channel Immediately need SEO for your KZbin channel I am waiting for your response. Thank you.

Hello sir! I hope you are well. I have seen the videos of your channel. Your video is very good but your video optimization is very poor 1. SEO Score is very low 2. No Title - Description - Tag SEO friendly 3. No Share Social Media Platform and many problems on your KZbin Channel Immediately need SEO for your KZbin channel I am waiting for your response. Thank you.

I can be the first one to install a triple ceramic in a fully build Wil Cooksey, hook me up and I'll add the install featuring a super low number ultra rare C6 Z06

I would not be mad if you sent me a triple ceramic for my Wil Cooksey LS7 I just built, having some issues with slipping now. My tuner at JC Speed said your clutch is the one to have and since I'm in Charlotte North Carolina I'll come get it to save on the shipping.

your video quality is very good

if my top floating plate look like slightly bent/curve.. can be resurface?

Cant wait to install my twin disc in my 2014 Mustang!

Awesome this is great news! I just had my mantic installed for my 2021 Mach 1 with a qa1 carbon fiber DS and Ford Performance Half Shafts. It also has a Steeda suspension and procharger stage 2 setup. I was worried about chatter because I kept hearing about it from forums. I will be picking my car up next week and can’t wait to drive it! Thank you Mantic!!

Is awesome! I highly recommend it!

Ops! we'll make that mistake a little tire

Hello, What effect the clutch pedal force? pressure plate spring or Clutch Master Cylinder or Slave Cylinder?

Yes! I’m motivated to build something that needs a real clutch like yours! This is so funny

I see neither velvet, nor hammer, where did you hide them?

Very nice and professional installation. Mike is definitely happy. Thanks for sharing.

Can't wait to get a mantic clutch bolted up in my next project

Best clutch company there is, hands down. 🇺🇸💪

That thing fucks 🍻

We need Geoff to do a podcast

Forgive me for a dumb question, how can i assure i've given it 1/2" of preload?

Yeah the CSC concept is kind of foreign to me as well. I've been fighting a high RPM lockout issue on my 2010 Mustang GT since I got it. I've done all the upgrades to fix the issue, yet it's still there. And now it's progressed to the point of the trans itself is now acting up (grinding going into 3rd gear). The clutch still grabs hard and I have yet to feel it slip but apparently the slave is just not pushing the fingers far enough. Never in my life have I changed a clutch that wasn't slipping but I guess that is the issue. To make matters worse, the OEM service manual (Ford OEM manual, not Haynes or anything) for my car says NOTHING about this process of to get the travel correct. Thank you for the video, this pretty much summed up and solved my issue and I'll be clutch / trans swapping shortly and I'll more than likely be getting a Mantic clutch if its available for this car.

2019 Mustang GT, MT82. Have Eric Bain's Bluefire Motorsport doing 61mm twin turbo build on it. Looking at 800-900rwhp. Little dig racing, but mostly roll stuff. Stock MT82. Recommendation please for your clutch please. Thank you.

It still seems weird to me that the throw out bearing is always pressed against the pressure plate fingers even when fully disengaged. I just replaced the clutch in my F-150 and the whole concept seemed so wrong

Why would you leave the cylinder with the bearing facing up like that and the line at the bottom? Air bubbles go up not down. That method looks like it would be great at trapping a lot of air.

I feel like someone owes me money for watching that.

Ok how is that something to be proud off 800hp take 11 sec to get down the strip 😂😂 with an upgraded clutch kit what does it do? Nothing

😔 p̶r̶o̶m̶o̶s̶m̶

How about a two piece flywheel that uncouples the outer three inches, via electro magnetism, slipper clutch concept? Creating a street/low mass "dual flywheel" effect, for usage. Where the magnetism could also aid the clutch grip.

These things are awesome! If you want the best this is it! Just had mine rebuilt and splined for my Tremec Magnum XL swap. I can't wait to get her back together!

We're trying to bleed a hydraulic clutch on a 1991 Cheverly gmc

Why does some installation warns not to push bearing prior to installation, what damage can it cause? Also can pulling vacuum from the master cylinder reservoir cause the bearing to retract and cause damage?

Does this mean that Mantic Clutch USA will be at SEMA 2022?

!

Sweet

How much does that unit weight?

Is your clutch very soft after doing replacing the clutch and slave cylinder. I got mine back from the mechanic and it feels like i am stepping on marshmallows

Yes!!!!