Any vehicle with a clutch fan I just replace it with the water pump

I have a 2009, the 2 passanger venta barely blow cold air, but blow the same as de pilot... Any ideas?

Do have a installation video? Thanks

The video is right

💪👍👍💙🏇🏇🏇

Thanks 😊 so much for ur video I’ll check my truck 🛻 tomorrow take care friend ✌️😻

If you need rear tailing arm bushings and you also plan to keep the vehicle for a while (low miles, no rust, etc.) do yourself a favor and get the poly bushings. I've found that the bushings in both the front a-arms and all the rear ones that are parts store replacements rarely last more than two or three years. The only issue is, removing the old bushings is a PITA. There are multiple ways to do this, and I'm really not sure which is the safest as far as preserving the structural integrity of the ctl. arms. The first and probably easiest is to set the tailing arm(s) in your fire pit in front of a butane torch flame for a while until the rubber burns away and the outer metal ring will just fall out. Not sure how much heat the control arms can take or if that will weaken them, but I wouldn't let them get glowing red and once the rubber starts to burn away it should keep burning and fall out pretty quickly without more heat applied. The second is to remove the center of the bushing and cut through the rubber (or around it so it can be removed which helps) and into the outer metal race being VERY careful not to go too far and compromise your ctl. arm. Then use an old chisel or screwdriver to hammer in and peel it out starting where you scored it.

This is incorrect.

I had a question. When I decelerated my rear end wobbies from left to right could it be the control arms.I have a 2001 qx4. So far what what was replaced is the front and rear struts.

Good info. Thanks for taking the time.

Wow I have the same problem! On my way to fix it now. Thank you! :-)

Use Hayden fan clutch

My truck began heating when using ac or when idling today after 15 years of use. Glad to see this component test is super easy. Thank you for the video.

Wrong in so many levels.

Only video I saw removing from top. This is absolutely the way to go. Thank you, Omar!!

This is quite the job so many thing to remove to get at those struts

I’m gonna do my lowers can’t wait to stop the death wobble Did you have to use new hardware? If so where did you find it ?

Why are clutch fans needed?

Thank you

Super helpful thanks

Just did this. Easy peasy thanks to this video. Awesome job!

What size Allen wrench was it

Do you know what brand of starter you put in?

My qx4 drives fine till I hit 1 little bump then it will start violently shaking. Does that sound like this?

Todo errado esse teste

what did u camera die so u said fuck it...have fun?

Put a lighter to the spring and watch it lock up

Ur advertising the wrong thing,,, DELETE UR VIDEO BUDDY, the fan clutch is supposed to lock up when going at extreme rpms not by hand, bu hand it only loosens because there is not heat, with heat on the spring it will lock up, go ahead and put fire on the spring in front and watch the clutch lock up,, u guys make people go buy parts that they dont need, ur fan clutch is fine, if u spin it when its cold and it doesnt spin the first few times than its a good fan clutch

Thats incorrect

U didn't finish

I have a 2004 qx4 steering wheel is making noise when turning not loud. Steerling wheel fluid is good. Maybe rack & pinion replacement? What are your thoughts

Did it fix it?

Horrible video

Thankfully for this super helpful

Bro u did nothing to show what u did to replace it , waste of time thanks I want a refund of 3mins or so

This helped me so much and moderately easy. Thank you!

You started off great then just left me hanging...

Thanks SOOOOOO MUCH BRAH'MANE,HAD a HELLUVA. EXPERIENCE

I appreciate the top side removal instructions. I could use the lift at work, but of all my tools are at home. BTW...Have you watched the video for the $10 fix for these starters? The bendix is loose because of a broken ignition lever inside. Dealers and most parts stores don't carry it, but it can be purchaed online. Hyundai part is 36131-2g100-fff. Thanks again!

A lot of people on forums say to do the job with the Jacks on the frame rails. Is it better to use the Jack stands on the axle like you?

Remove that bracket or you won’t get it back in lost 3 hours messing with it took ten bracket out went right in

Appreciate this man.

Interesting clothing to wear to work on a car

Great start, don’t even know how to remove struts. Shade tree mechanic.

whats the part number to fix this

This is happening with my 08 right now. What was the fix on this?

hola tengo el código p0012 que puede ser ?

Hey thanks brother! Mine 2010 was doing the same thing, the bendix was not engaging! But got a new starter, and Bam 💥 all good thanks again saved me 400$

Thanks Brother, Heck i thought is was gonna be way more involed, my starter was also doing the same thing the bendix would not engage tus it just would spin, thanks man...

Will do compadre!! 👍