Shoud have talked without the shield

You think paint stay in the fluid lines that would be bad .i cleaned a gravity fed gun thinking all had to do was let paint run through but afterwords i looked in fluid passage way and there was still paint in it

no thinning required??

Marty trained a couple guys and I at the Sherwin Williams training center in Illinois the last couple days. He knows his stuff...

Wonder if regular air compresser tank will work?

I was super please when I used this kit on my 16 year old truck. It really works.

The Munsell color system has five hues. Can you take out purple and it still be the Munsell Color System?

OR, just just a damned paint tray. OR, just use a one inch foam roller in a cup. there are so many stupid things that happen when you use a foam roller this way....the man in the white bunny suit attempts to address the "ridges" that created with this dumb angled roller method...instead a company like eastwood prefers to show you how to make rolling epoxy and very awful way to do it that will require a LOT of work later to get all that stepped ridge out...Might as well just dump epoxy and spread it with a brick. This is a very dumb way to roll epoxy. No one should be shown to do it this way. Awful...stupid...and wrong.

Dont forget adhesion promotor on raw plastic

I teach, among other courses, high school body and paint. This was great teaching. Such an efficient way. Well done. I will use what you have laid out here for sure. The other video on the three dimensions of color was equal in quality. Thank you.

Them pot liners are an absolute waste of time and money

I did this the following day and it was only air dried. I had a fender that looked like Niagra falls. The clear was finish one. I dunno if I got lucky, but it's doable in a pinch if you need the car out the door.

I want to use your products

Have you measured the clear coat thickness with a digital paint depth meter? I’m curious to know how much clear is left compared to the surrounding areas ?

And if it's just clear coat you don't need the Bondo wet sand and clear it again

That's a good trick I've used it before my question is why are you mixing the bondi with the spreader shouldn't you be using a paint stick so you don't get your spreader messed up with some Bondo and some hardener trying to spread it on and getting the wrong mixture and then it won't stand off mix your Bondo with a paint stick it saves you a lot of grief

I pooped today.

Awww time for a update vid please!

Here in brasil i just use s.w products ... its the best.

Used this on my 2003 VW Cabrio headlights! Unbelievable....like new! Brilliant! Highly recommend. Spent a good deal of time on steps 1 & 2 as suggested. For under $30 Cdn over Amazon it is remarkable!!!!!

am looking for rotary hand spraying gun for latex , Can you help ?

I'm using this paint I like it water base

I have been using E2A933 after media blasting for over 5 years. It adheres to the profiled substrate like no other. I know when I use 933 I will not have a problem with adhesion. This is the best DTM I have ever used. I will reference your video to my customers, very informative. Thank you, Joe DBTX

what is the name of the filler your using can you give us a link

First of all, a good painter shouldn't causes a run. well, ok, no one is perfect. Sh** happens, and when it does, don't fake it by removing the clear coat and replace it with polish. Redo if it is taking you more time. You screwed the job, you fix it right, don't screw your customer.

Marty is like a painter scientist

There can't be enough clear left after doing this. It should be flow coated at the least. If the painter is running clear this badly, he shouldn't be painting.

Great job..I've done this method and no I didn't spray gallons of clear. I also didn't start with this gentlemans starting grit.

I was hoping that one of these videos would tell me how to connect the compressor to the pressure pot for painting. It looks like the spray gun has 2 inputs, 1 for the air and 1 for the paint. I only have one line coming off of the compressor, so do I get a splitter and split the pressure between the two or do I have to get a second compressor to feed the pressure pot while the first one feeds the gun? I asked the store where I purchased the pot and they are somewhat less than responsive!

Wish I knew this last week

Scraping a razor blade over the run is faster, easier, and less material.

Using that DA sander is not a good idea for Harry homeowner. As mentioned by others, start with a fresh razor blade and scrape the bulk of the run off first. Then you can move to 400-600 grit on a block. I am shocked that he didn't cut thru on this job. Must have had a lot of clear on that panel.

We have been doing this for years with lacquer primer Or application with brushes

Excellent!

availble in India .

How would one go about removing water drops that dripped on to the clear while spraying the clear coat ?

do you have availble India ?

This is a very helpful video to help you set up and clean a pressure pot paint system, thank you for sharing

Masking tape on both sides of run with 1000 grit works excellent.

That’s a diabolical run on that panel it would be quicker to repaint obviously that panel been around sometime for the lacquer to be rock hard no way would you attempt to repair that run under normal circumstances lacquer will be to soft could be misleading to a d i y enthusiastic enjoyed watching

Ask the experts at Sherwin?? Next time your rep is sharing his expertise on ANY product or piece of equipment, invite them into the field to show it to you using best practices. Unfortunately their expertise starts and stops with the fine tuned skill of regurgitating what they’ve been told at the innumerable trainings and conventions. Which btw, are incredibly well thought out. Right down to the VERY INTENTIONAL omission of any hands on product training or competitor side by side comparison. But after they’ve told several hundred times the start to really believe it..... kinda brilliant in a way, but very misleading for anyone looking for actual information.

Holly Smokes! I just became a pro painter.

Paint paddle with 1200 grit wet or dry sand paper wrapped around it. Stay on top of the run when standing. Then go to 2000 grit and buff. Idk who shoots a fender vertical, indtead of horizontal, there would be less of a chance of running.

don t want to see power point but how it really work test

i hope whoever sprays the same material you used, will use the same airflow masking system you wore. You barely sprayed any material but you had on a hazmat suit for virus contaminations. Are your products that dangerous that painters should use more caution?

So the filler is a buffer to the low spots?

Where can I get the 2 litre disposable pot liners ? I can find them anywhere

And now we go from 1200 to.......oh fuck I've gone through 🤣🤣🤣

Amazing work🙏💝🇮🇳🌹

But why didn't you show the outcome