17 жыл бұрын
Пікірлер
@BuckAugust 9 жыл бұрын
Beautiful to watch
@PacoOtis 9 жыл бұрын
Wow! Very nice work! However, if you would even think about wearing some protective gloves it just might make your career a bit better. Surely you can be safe and still be the excellent artist you are. Best of luck!
@WhatIsThisVid 9 жыл бұрын
+Joseph Stokes Actually wearing gloves while operating a lathe is a big safety hazard, and if they get caught in the spinning mass it will quite possibly rip your hand off still in the glove or if your lucky just a finger. So he is being quite safe, you can view some videos of why you shouldn't wear gloves on a lathe on this very site
@BuyMyDreamHotel 9 жыл бұрын
+Joseph Stokes Joseph this is a very common comment. Some metal spinners advise against gloves because they fear their arm can be pulled in in the leather glove catches - there appears to be no consensus of opinion but its not safe to assume that an experienced spinner is being slack on safety because you see him not wearing gloves it might be a deliberate and calculated decision. I have been spinning for only one year but I do not choose to wear gloves as I am wary of them catching - as far as safety is concerned I choose to trim the otherwise ragged edge as smooth as possible as early as I can so that if I do touch it by accident it wont cut as badly. Many machine operators prefer not to wear gloves for similar reasons - in many cases leather would offer very little protection against more than a bad scratch and there is a risk of infection if leather particles get embedded into a raggedy cut. You think it through and make the best decision you can on the information you have to hand but the casual observer may of course conclude think its laziness or forgetfulness.
@LafeWood 8 жыл бұрын
+Joseph Stokes Actually wearing gloves while operating almost anything with spinning parts is UNSAFE, for the same reason that wearing a tie or loose sleeves would be a bad idea. Better to cut your fingers than have your arm wrapped up in the lathe because your glove got caught on something! I'm not trying to pick on you, I just don't want to see anyone get hurt.
@thomashanson6607 9 жыл бұрын
I remember my father making rocket nose cones like this in the 60's, Big lathe. I was in awe.
@Meuseraner 9 жыл бұрын
hard work
@craigwilliams1835 10 жыл бұрын
Hi, I'm looking for a few one-off pieces to be spun and the cost for tooling is huge with all the large CNC spinning manufacturers, could anyone point me in the right direction of finding a hand spinner who does commission work?
@woodbrassandglass 11 жыл бұрын
what is the thickness of metal you recommend for your parts?
@danielhoffman2299 11 жыл бұрын
sorry I didn't read your work hardening comment before I asked the question..
@danielhoffman2299 11 жыл бұрын
Wow what an art... I would love to try some simple stuff on my small engine lathe but it looks dangerous and complicated...I have been a sheet metal worker for thirty years and still have all my fingers... That being said, any pointers for a true beginner..also how do you deal with work hardening while you form the parts. ?
@bobbobby62 11 жыл бұрын
I have been a spinner for a few years,but this was quality demo,thanks,keep on spinning!
@mark5161st 11 жыл бұрын
i worked for koch metal spinning in buffalo,ny.we made a lot of aircraft parts.i did not see anyone using the "spoon" tool to spin in these video's yet but i did see there are different ways people prefer.like my boss said"spinning is like an art" and i agree.i did more of the machining aspect so i don't know hands on.great stuff
@srussert28 11 жыл бұрын
I have a 2 1/2" sphere with a 1 1/4" hiole in the end that I need to have made. Is this a similar method to how that would be done.
@MrCelestinoclemente 11 жыл бұрын
Hi, I have a metal and a wooden lathes, I would like to ask you is, which one shall I have a go? Or does the spinning art requires a proper lathe?
@beardedwoodpecker 11 жыл бұрын
Great video , thank you for sharing your workmanship with us
@sigung01 11 жыл бұрын
I thought this video couldn't get any better until the music cut in. Whatever that music is, it's brilliant, as is the metal spinning.
@pipinghotpiper 12 жыл бұрын
Hi, I live in Peterborough Cambridgeshire and I am desperate to learn soem metal spinning technique a for the purpose of making mounts for bagpipes and small pipes. I would love to get about a month with someone who knows what they are doing. I am a professional competiting Bagpiper and also a carpenter and woodturner. They don't have to live near me as I will travel to learn. can anyone help me please. many thanks in advance, James
@JOEGGGJOE 12 жыл бұрын
wow. that was great. good job.
@Nthefastlane 12 жыл бұрын
That's really neat!
@madwilliamflint 12 жыл бұрын
neat! I've had a home machine shop for a couple years, doing minor hobby work. But I'd somehow I'd never actually heard of metal spinning.
@ArnoldsDesign 12 жыл бұрын
I have a box of wrinkled annealed 1100 alloy aluminum parts so far. I've tried spinning annealed c260 cartridge brass too, but it work hardens on me very quickly, so I know where you're coming from.
@stillbashingmetal 12 жыл бұрын
Try annealing the metal. You may have to "pickle" it as well. Look up annealing and pickling sheet metal on google.Been too long since I've done it to give any precise help, but maybe this will send you in the right direction.
@tamrakarsagun 12 жыл бұрын
What types of metals can be used for spinnin
@MilPlanes1 12 жыл бұрын
Wow! Good skills buddy. I can watch this sort of thing all day long.
@vambreace 12 жыл бұрын
WWOOWW!... what i can say beautiful i never seen that work before!. that is the artist work!!!!. thanks for share!!!!!!!!
@andylarkin100 12 жыл бұрын
Hello, I am attempting to spin a trumpet bell (where the sound comes out) out of a .020" sheet brass disk. Can you offer any advice on lathe speed, pressure or feel? I can only get a few inches before the disk wrinkles inward. Thanks!
@recommendme 12 жыл бұрын
is this a similar process as making the end of a trumbone... i saw it on "how its made" and they did something similar.. its reallly cool...
@spleno1 13 жыл бұрын
Damn buddy, thats pretty cool.
@herVonStrumpel 13 жыл бұрын
what kind of steel do you use for this? or aint it steel?
@dontbe 13 жыл бұрын
Where do you get the blank disks?
@sledsandtrucks 13 жыл бұрын
That has to be one of the coolest things I have seen in a while. I may have to give this a try.
@MatsNorway 13 жыл бұрын
What is the end of the tool made of? We tried to do this but i think we need bronse or something soft as a tool.
@Bobbyl007 13 жыл бұрын
Now I want to make room in hte shop and start looking for another machine. LOL.
@owenaero 13 жыл бұрын
exelent
@FrenkMI 13 жыл бұрын
GREAT VIDEO!!!! My father, 68 year old now, it has been a "metal spinner" since the 1978!!! Now he's retired from almost 3 years, but I remember very well this manual work!! Movements, sounds, tools, everything!! It miss only the smell of the lubricant!! :-) BTW my father has heavily modified one of the two turner putting some "half-automatic" parts to reduce the body stress
@splodeyfrog 13 жыл бұрын
Gonna make a cone for my Dobro now!
@montey1017 13 жыл бұрын
cool...and...well...I have to say it...awesome accent
@LowCostCncRetrofits 13 жыл бұрын
Yeah thats clever alright !
@annabelsoothill 13 жыл бұрын
Excellent, thanks for putting this on!
@malayrojak 13 жыл бұрын
Can someone please tell me the name of the music/artist that starts playingat 2:31? Cheers!
@keni4412 13 жыл бұрын
wow, what a great work Mr!! We call like this technology HERASIBORI in Japan good job any way,
@BrianMDPhD 13 жыл бұрын
Oh wow now that is an art form. Don't see much skilled labor like that anymore..
@drjazzisme 14 жыл бұрын
@Aczernek hi.i think you can see how he makes the thickness uniform by scraping/cutting the ridges down,thats when you see shavings flying off.and having done woodturning for a hobby i know he's a very skijjed person.woul love to have a go though,that aeroplane spinner is just magic.
@calholli 14 жыл бұрын
cool.. I didn't have any idea what you were saying until you started the work.. very nice!! .. I always wondered how so many things are seamless.. now I know.
@DORUKOZKAN 14 жыл бұрын
wow thats hella cool !
@shinyfuzzy 14 жыл бұрын
@nikhilphillips i dont see why they couldnt be made like that
@Leebm29 14 жыл бұрын
very impressive
@checazzovolete 14 жыл бұрын
bellissimo lavoro artigianale
@cosast54 14 жыл бұрын
English accent but cant localize
@corderopilot 14 жыл бұрын
just awesome!
@aaanry 14 жыл бұрын
excellent work! Thank you!
@nikhilphillips 14 жыл бұрын
AMAZING WORK! but dont you need to wear some sort of safety gear while doing that? you could get seriously injured! i'm wondering if two stroke expansion chambers can be made like that. well can they?!